Initial creation of new system manager driver.
Add supports for the SOCFPGA System Manager Register block which
aggregates different peripheral function into one area.
On 64 bit ARM parts, the system manager only can be accessed during
EL3 mode, this driver model provide user the high level access
to system register and abstract user from low level access.
The base address of system manager can be retrieved
using DT framework through the System Manager driver.
Signed-off-by: Tien Fong Chee <tien.fong.chee@altera.com>
Signed-off-by: Boon Khai Ng <boon.khai.ng@altera.com>
Branch contains bringup of Acer Iconia Tab A500 (codename picasso), a
Tegra 2 Android device with decent Linux kernel support. Ondevice tests
and U-Boot test suit all passed.
Defining CONFIG_MT8512 is unnecessary as now board for mediatek
target can be changed in config.
Use CONFIG_TARGET_MT8512 to replace CONFIG_MT8512.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Not all MediaTek platforms needs u-boot-mtk.bin.
This patch will let u-boot generates u-boot-mtk.bin only if
CONFIG_MTK_BROM_HEADER_INFO is not empty.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Tom Rini <trini@konsulko.com> says:
This small series separates "bloblist" and "standard passage" to allow
for these similar concepts to explore solutions to problems without
introduces breaking changes to the other.
Link: https://lore.kernel.org/r/20250220000223.1044376-1-raymond.mao@linaro.org
Refactor the xferlist to remove the relocating when bloblist passed
from the boot args.
Refactor bloblist init to use incoming standard passage by default
if a valid transfer list exists in the boot args.
For bloblist relocation, use the actual total size if it has a smaller
BLOBLIST_SIZE_RELOC.
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Suggested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The device tree for rk3036 combined is now
available in the /dts/upstream directory.
Use imply OF_UPSTREAM to migrate all rk3036 boards.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Most Rockchip SoCs use 0x0 as DRAM base address, however some SoCs use
0x60000000 and RK3576 use 0x40000000 as DRAM base address.
CFG_SYS_SDRAM_BASE is defined with correct address for each SoC and
U-Boot proper use this to set correct gd->ram_base in setup_dest_addr().
SPL never assign any value to gd->ram_base and instead use the default,
0x0. Set correct gd->ram_base in dram_init() to ensure its correctness
in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
U-Boot only works correctly when it uses RAM below the 4G address
boundary on Rockchip SoCs. Limit usable gd->ram_top to max 4G.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Allow the first bank to extend beyond 4 GiB when the blob of space for
peripheral is located before start of DRAM, e.g. when start of DRAM
is 0x40000000 and continue beyond the 4 GiB mark.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In the GRF header file, some instances of UART2 pinmux are prefixed with
"GRF_UART2DBG" while others have "GRF_UART2DGB".
Since UART2 is the default console UART and used for debugging, it is
more likely the name should be UART2DBG.
Fix the ones that are wrong.
Fixes: a2c08df3813b ("pinctrl: add driver for rk3399")
Fixes: fa72de10452c ("rockchip: arm64: rk3399: move grf register definitions to grf_rk3399.h")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Paul Kocialkowski <paulk@sys-base.io>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
These power rails must be on very early for the U-Boos TPL banner to be
show over debug UART.
This reverts commit 4576e65a5d6b10fd207c3a44061676ce0220d794.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
These power rails must be on very early for the U-Boos SPL banner to be
show over debug UART.
This reverts commit af518a1dfe637cb4dc486d7a832585e4a48bc970.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The PCS exists only in GMAC1 and relates to SGMII interface and
is used to control the SGMII PHY.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
[trini: Adjust slightly for white space and to move 'start' to within if
block]
-----BEGIN PGP SIGNATURE-----
iQFNBAABCgA3FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmezAjIZHGV1Z2VuLmhy
aXN0ZXZAbGluYXJvLm9yZwAKCRAesx4CDqwvyINKB/0ZT5kVOSlRBYOewxacnN3a
2znMr+c/VbXq+lPkT8rk6QREBKdqa8u3S3puJMepqrw8Zc32hJhJjGgeFkmUU7vf
0U/QcFO7I0ROZfD0tDA2IiH5hlRqu73PsRb2jSzxHSBmlXtFN9njBwaI4GO5Gm7j
2Sey5xSiN7DGp2Te1qey01q5Mlr8iFuqUAKQvlZ4/ZkJkclUxsHV4aURSI5PPvBq
QEaWTMtZp541Bt+6C6JSoNVSNUgSXFCzWK3P8YuJFbdYUJfJyXA2cSwXAXSJ7Mjx
vpgsdwkI4kB6sRZ0ZGgd//dpN8PrzqbXFfRfcYKHCFPQznl8JW9Hdbiqxxn9Dbol
=/zXG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2025.07-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2025.07 cycle:
This feature set includes improvements on the atmel-quadspi driver, a
fix for the nand driver, and improvements on the pinctrl driver to be
able to use the Linux DT (also sync on the DT side as well).
The Acer Iconia A500 is a tablet computer designed, developed and
marketed by Acer Inc. It is powered by 1 GHz Nvidia Tegra 2 processor
and 1GB DDR2 RAM. The A500 is sold with 64 GB, although both 16 GB
and 32 GB models are available.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Add empty weak assembler function armv8_switch_to_el2_prep() which is
jumped to just before U-Boot determines which EL it is running in and
decides which path to take to boot the Linux kernel.
This weak function is meant to be used by architecture specific code
to implement jump to a firmware blob, which then returns right past
this weak function and continues execution of U-Boot code which then
boots the Linux kernel. One example of such use case is when U-Boot
jump tp TFA BL31, which switches from EL3 to EL2 and then returns to
U-Boot code newly running in EL2 and starts the Linux kernel.
The weak function is called with caches already disabled and DM shut
down. Any preparatory work or even loading of more data must be done
in board_prep_linux(), this hook is meant only for the final jump to
the firmware and return to U-Boot before booting Linux.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Judith Mendez <jm@ti.com> says:
Some K3 devices like am62x and am64x have a M4 processor in the MCU
voltage domain. This patch series introduces remoteproc M4 driver which
will be used to load firmware into and start the M4 remote core.
This series also adds support for R5F cores on am64x SoCs in patch 2 and
sets up environment to load FW in remote cores in patch 3,4,5.
This patch series also enables remoteproc drivers by default as per what
remoteproc sybsystem is supported per SoC, thus all remoteproc options
are now deleted in configs/* since they are no longer required.
This patch series was tested on am64x EVM, am62x SK, am62ax SK,
am62px SK boards.
Any additional tested by's are welcome since I was not able to
test any additional boards.
Tested by running the following commands in u-boot prompt:
=> setenv dorprocboot 1
=> run boot_rprocs
Link: https://lore.kernel.org/r/20250210202944.1071931-1-jm@ti.com
Add remoteproc config options to enable remoteproc drivers by
default as per what remotproc subsystem is supported on each
SoC.
Signed-off-by: Judith Mendez <jm@ti.com>
PLLD2 is a simple clock (controlled by 2 registers) and appears starting
from T30. Primary use of PLLD2 is as main HDMI clock parent.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
PLLD2 is a simple clock (controlled by 2 registers) and appears starting
from T30. Primary use of PLLD2 is as main HDMI clock parent.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The GPIO banks are added as sub nodes or child nodes under the
pinctrl node (as per Linux ABI) and the reg property which points
to an array of controllers physical base address is removed
to align with the Linux devicetree.
Signed-off-by: Charan Pedumuru <charan.pedumuru@microchip.com>
Signed-off-by: Manikandan Muralidharan <manikandan.m@microchip.com>
Add the missing properties for the pinctrl node and for its
corresponding GPIO bank nodes to align with the Linux DT.
Signed-off-by: Manikandan Muralidharan <manikandan.m@microchip.com>
Reviewed-by: Eugen Hristev <eugen.hristev@linaro.org>
Move pinmux nodes defined under the pinctrl node from sam9x60 SoC
DT to its board specific DTS files.
Signed-off-by: Manikandan Muralidharan <manikandan.m@microchip.com>
Reviewed-by: Eugen Hristev <eugen.hristev@linaro.org>
Define the pinctrl nodes with its label to align with the Linux DT.
Without this change the pinmux nodes are grouped under an additional
'pinctrl' child node which is not identified by the pinctrl driver
when the GPIO banks are made as child nodes of pinctrl node.
Signed-off-by: Balamanikandan Gunasundar <balamanikandan.gunasundar@microchip.com>
Signed-off-by: Manikandan Muralidharan <manikandan.m@microchip.com>
Reviewed-by: Eugen Hristev <eugen.hristev@linaro.org>
Add Advanced Interrupt Controller node and define it as interrupt
parent in sam9x60 SoC DT.
Signed-off-by: Manikandan Muralidharan <manikandan.m@microchip.com>
Reviewed-by: Eugen Hristev <eugen.hristev@linaro.org>
u-boot-dfu-20250211:
CI:
- https://source.denx.de/u-boot/custodians/u-boot-dfu/-/pipelines/24556
Android:
- Handle boot images with missing DTB
Usb gadget:
- Fix nullptr in g_dnl when serial# is unset
- Add missing schedule() in f_mass_storage gadget
- Add support for STih407 in dwc3-generic
- Fix usb clocks on STih407
- Migrate STih407 to DM_USB_GADGET
On STi platforms, all clocks are enabled by BOOTROM, so CONFIG_CLK is
not set as no clock driver for STI exists.
As ehci-generic and ohci-generic drivers are used on platforms where
CONFIG_CLK is set, clk_get_bulk() returns-ENOSYS in case of
stih410-b2260.
To avoid this error, add fixed clocks for ehci and ohci nodes for
stih410-b2260 to fix the following errors:
Bus usb@9a03c00: ohci_generic usb@9a03c00: Failed to get clocks (ret=-19)
Port not available.
Bus usb@9a03e00: ehci_generic usb@9a03e00: Failed to get clocks (ret=-19)
Port not available.
Bus usb@9a83c00: ohci_generic usb@9a83c00: Failed to get clocks (ret=-19)
Port not available.
Bus usb@9a83e00: ehci_generic usb@9a83e00: Failed to get clocks (ret=-19)
Port not available.
scanning bus dwc3@9900000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20250130163547.512990-2-patrice.chotard@foss.st.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Judith Mendez <jm@ti.com> says:
This patch series enables ESM reset configuration in board_init_f
for am62x and am62px devices.
This is necessary in order for error events to reset the system.
This patches are tested using watchdog to reset the system via ESM.
Link: https://lore.kernel.org/r/20250129234403.574766-1-jm@ti.com
On AM62A and AM62P devices, it is possible to route Main ESM error
events to MCU ESM. MCU ESM high error output can trigger the reset
logic to reset the device. So, for these devices we have Main ESM and
MCU ESM nodes in the device tree. Add functions to probe these nodes
if CONFIG_ESM_K3 is enabled.
Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
Signed-off-by: Judith Mendez <jm@ti.com>
This patch enables switch auto-detction for mt7981 as some new mt7981
boards will use AN8855 ethernet switch.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Add bootph-all properties to I2C0 nodes to ensure the bus and EEPROM
are accessible across all stages. This enables reading the SoM
configuration at any point during the boot process.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Tested-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
The change from pinctrl to pio was missing in mt7986-u-boot.dtsi and will
cause build failure. Now fix it.
Fixes: f1775996ba9 (mediatek: mt7986: move gpio-controller up and rename pinctrl to pio)
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Heiko Schocher <hs@denx.de> says:
In linux we have the option to create the name of a led
optionally through the following properties:
- function
- color
- function-enumerator
This series adds support for parsing this properties if there
is no label property.
Link: https://lore.kernel.org/r/20250128135246.74838-1-hs@denx.de
[trini: Document name parameter in led.h]
in linux we have the option to create the name of a led
optionally through the following properties:
- function
- color
- function-enumerator
This patch adds support for parsing this properties if there
is no label property.
The led name is created in led_post_bind() and we need some
storage place for it. Currently this patch prevents to use
malloc() instead it stores the name in new member :
char name[LED_MAX_NAME_SIZE];
of struct led_uc_plat. While at it append led tests for the
new feature.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Kconfig should not display the STATIC_MACH_TYPE option when
SUPPORT_PASSING_ATAGS is not selected. For example, when using most
platforms with menuconfig, it shows the STATIC_MACH_TYPE option causing
confusion. As we know, this should not occur when SUPPORT_PASSING_ATAGS
is not selected
[trini: Reword commit message]
Signed-off-by: Liya Huang <1425075683@qq.com>
ARMv7-M architecture uses NVIC instead of GIC.
NVIC is an interrupt controller specially designed for
ARM Cortex-M series processors.
Signed-off-by: Liya Huang <1425075683@qq.com>
CONFIG_XILINX_OF_BOARD_DTB_ADDR holds DTB address which U-Boot is checking.
Currently address in binman match default value but macro can be used
directly.
Also sync node name (s/hash-1/hash/) and sync location to have the same
order load/hash/image.
All binman DTSes are compiled that's why also guard
CONFIG_XILINX_OF_BOARD_DTB_ADDR which depends on OF_BOARD || OF_SEPARATE
which is a problem for mini configurations which are using OF_EMBED.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/a22c9671b965b222bfd419f5bfaee012929f3d88.1738659214.git.michal.simek@amd.com
Add ethernet aliases to CC (Carrier card) description to create a
connection which is used by fdt_fixup_ethernet() for updating
local-mac-address in DT.
On Kria SOM MAC address is read from i2c eeprom at start and based on it
environment variables are created. Without creating aliases U-Boot is not
able to inject local-mac-address DT property and OS won't get the same MAC
address unless another i2c read is happening in OS.
Also aliases are using string not phandle that's why full path has to be
provided but that shouldn't be a big issue because location of ethernet
controller is fixed.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/6d360e71a0530d201578e27a6997dbd472772e39.1737466907.git.michal.simek@amd.com
Output images are generated via Binman only if SPL is enabled, as
there is no consumer for them otherwise. An #ifdef check ensures that
when SPL is enabled, Binman generates the U-Boot ITB. If SPL is disabled,
ITB generation is skipped since the ITB format is supported only by SPL.
Without SPL, generating such an image is unnecessary, as it would not be
used
The second reason is that when a DTB is passed, the current logic cannot
handle it without an additional step in U-Boot to parse an appended FIT
image and enable board-specific code to select the correct DTB config.
The MULTI_DTB_FIT configuration should be used if support for multiple
DTBs is required, but SPL is not being used.
Signed-off-by: Prasad Kummari <prasad.kummari@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/7cba738ae36dacf7d1b0cfbaf13e0c9b3a0df225.1737462296.git.michal.simek@amd.com
