Use PHASE_ as the symbol to select a particular XPL build. This means
that SPL_TPL_ is no-longer set.
Update the comment in bootstage to refer to this symbol, instead of
SPL_
Signed-off-by: Simon Glass <sjg@chromium.org>
When supporting partition reset for SoC such as i.MX95 , the Linux
Kernel may have configured the tuning, while after force reset by
wdog or else, uboot CMD0 will never pass unless config RSTT to reset
tuning logic.
Since RSTA and RSTT are independent, so need both to be reseted in the
controller.
Acked-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The memory of priv and plat are leaked if max_bus_width is wrong.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The plat->cfg is wrongly memset to 0, so the host_caps value configured
in fsl_esdhc_initialize is reset. Remove the unnecessary memset since
plat is allocated via calloc.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
According to SD and MMC spec, 74 clocks must be sent to device after
power stable. This is need in reinit ops for DM MMC or init ops for
non-DM MMC after power cycle.
So set the INTIA to send 80 clocks in esdhc_init_common and move
its calling from probe to reinit.
However, on 8MQ EVK and 8QXP MEK with some brands of SD cards, sending
80 clocks may not work well.
The root cause is related with power up time. According to spec, after
power stable, host shall supply at least 74 SD clocks to the SD card with
the maximum of 1ms. However, the power ram up time is related with the
characteristic of SD card. At the moment of sending 74 SD clocks, the
power probably not ram up to the operating level on the problematic
cards. Then cause the cards not ready.
This patch changes to send SD clock with 1ms duration to replace 80
SD clocks (0.2ms at 400Khz clock).
This way meets the spec requirement as well, and adds the margin for
power ram up time to be compatible with the problematic SD cards.
This is also aligned with implementation which has FORCE clock
always on.
Reviewed-and-tested-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With partition reset supported for i.MX8QM/QXP/95 and etc, when linux
mmc runtime suspended, the mmc clks are gated off. While at same time
system controller reset Cortex-A cores because of various reasons(
WDOG timeout and etc), with SPL run again, only enable PER clk is not
enough, also need to enable AHB/IPG clk, here use clk bulk API to enable
all the clocks.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Allow MMC init when clock support is not enabled in a particular phase.
Refactor the setting of priv->emmc_clk so it is a bit clearer.
Signed-off-by: Simon Glass <sjg@chromium.org>
In case the cyclic framework is enabled, poll the card detect of already
initialized cards and deinitialize them in case they are removed. Since
the card initialization is a longer process and card initialization is
done on first access to an uninitialized card anyway, avoid initializing
newly detected uninitialized cards in the cyclic callback.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are lot of device_is_compatible() present in the driver.
Remove them and replace with a variables "SDHCI_COMPATIBLE_SDHCI_89A"
and "SDHCI_COMPATIBLE_VERSAL_NET_EMMC" with match data.
This change saves the space and reduce the execution time.
Signed-off-by: Padmarao Begari <padmarao.begari@amd.com>
Link: https://lore.kernel.org/r/20240913093157.2343476-1-padmarao.begari@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The JH7110 SoC uses a GPIO for card detect.
* In the of_to_plat function check if a cd-gpios definition exists and
request the GPIO.
* In the getcd function return the GPIO value in this case.
Reported-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
After resetting the host controller, program in the POR val for this
register just like the Linux driver does.
This seems to help with initialization when running U-Boot as the primary
bootloader on some boards.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Per JESD84-B51 P47, host need to change frequency to <=52MHz
after setting HS_TIMING to 0x1, and host need to set the
8-bit DDR buswidth. Currently setting the frequency to 26MHz
and trying to switch 8-bit DDR buswidth resulting timeouts.
mmc dev 1 0
Select HS400 failed -110
switch to partitions #0, OK
mmc1(part 0) is current device
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Cadence SDMMC v6 controller has a lot of changes on initialize
compared to v4 controller. PHY is needed by v6 controller.
Signed-off-by: Kuan Lim Lee <kuanlim.lee@starfivetech.com>
Co-developed-by: Alex Soo <yuklin.soo@starfivetech.com>
Signed-off-by: Wei Liang Lim <weiliang.lim@starfivetech.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tim Harvey <tharvey@gateworks.com> says:
Modern eMMC v4+ devices have multiple hardware partitions per the JEDEC
specification described as:
Boot Area Partition 1
Boot Area Partition 2
RPMB Partition
General Purpose Partition 1
General Purpose Partition 2
General Purpose Partition 3
General Purpose Partition 4
User Data Area
These are referenced by fields in the PARTITION_CONFIG register
(Extended CSD Register 179) which is defined as:
bit 7: reserved
bit 6: BOOT_ACK
0x0: No boot acknowledge sent (default
0x1: Boot acknowledge sent during boot operation Bit
bit 5:3: BOOT_PARTITION_ENABLE
0x0: Device not boot enabled (default)
0x1: Boot Area partition 1 enabled for boot
0x2: Boot Area partition 2 enabled for boot
0x3-0x6: Reserved
0x7: User area enabled for boot
bit 2:0 PARTITION_ACCESS
0x0: No access to boot partition (default)
0x1: Boot Area partition 1
0x2: Boot Area partition 2
0x3: Replay Protected Memory Block (RPMB)
0x4: Access to General Purpose partition 1
0x5: Access to General Purpose partition 2
0x6: Access to General Purpose partition 3
0x7: Access to General Purpose partition 4
Note that setting PARTITION_ACCESS to 0x0 results in selecting the User
Data Area partition.
You can see above that the two fields BOOT_PARTITION_ENABLE and
PARTITION_ACCESS do not use the same enumerated values.
U-Boot uses a set of macros to access fields of the PARTITION_CONFIG
register:
EXT_CSD_BOOT_ACK_ENABLE (1 << 6)
EXT_CSD_BOOT_PARTITION_ENABLE (1 << 3)
EXT_CSD_PARTITION_ACCESS_ENABLE (1 << 0)
EXT_CSD_PARTITION_ACCESS_DISABLE (0 << 0)
EXT_CSD_BOOT_ACK(x) (x << 6)
EXT_CSD_BOOT_PART_NUM(x) (x << 3)
EXT_CSD_PARTITION_ACCESS(x) (x << 0)
EXT_CSD_EXTRACT_BOOT_ACK(x) (((x) >> 6) & 0x1)
EXT_CSD_EXTRACT_BOOT_PART(x) (((x) >> 3) & 0x7)
EXT_CSD_EXTRACT_PARTITION_ACCESS(x) ((x) & 0x7)
There are various places in U-Boot where the BOOT_PARTITION_ENABLE field
is accessed via EXT_CSD_EXTRACT_PARTITION_ACCESS and converted to a
hardware partition consistent with the definition of the
PARTITION_ACCESS field used by the various mmc_switch incarnations.
To add some sanity to the distinction between BOOT_PARTITION_ENABLE
(used to specify the active device on power-cycle) and PARTITION_ACCESS
(used to switch between hardware partitions) create two enumerated types
and use them wherever struct mmc * part_config is used or the above
macros are used.
Additionally provide arrays of the field names and allow those to be
used in the 'mmc partconf' command and in board support files.
The first patch adds enumerated types and makes use of them which
represents no compiled code change.
The 2nd patch adds the array of names and uses them in the 'mmc
partconf' command.
The 3rd patch uses the array of hardware partition names in a board
support file to show what emmc hardware partition U-Boot is being loaded
from.
eMMC v4+ devices have hardware partitions that are accessed via the
PARTITION_CONFIG (Extended CSD Register 179) PARTITION_ACCESS
and BOOT_PARTITION_ENABLE fields defined as:
bit 5:3: BOOT_PARTITION_ENABLE
0x0: Device not boot enabled (default)
0x1: Boot Area partition 1 enabled for boot
0x2: Boot Area partition 2 enabled for boot
0x3-0x6: Reserved
0x7: User area enabled for boot
bit 2:0 PARTITION_ACCESS
0x0: No access to boot partition (default)
0x1: Boot Area partition 1
0x2: Boot Area partition 2
0x3: Replay Protected Memory Block (RPMB)
0x4: Access to General Purpose partition 1
0x5: Access to General Purpose partition 2
0x6: Access to General Purpose partition 3
0x7: Access to General Purpose partition 4
Add char arrays to provide names for these values.
Use these names which displaying or setting the PARTITION_CONFIG
register via the 'mmc partconf' command.
Before:
u-boot=> mmc partconf 2 1 1 0 && mmc partconf 2
EXT_CSD[179], PARTITION_CONFIG:
BOOT_ACK: 0x1
BOOT_PARTITION_ENABLE: 0x2
PARTITION_ACCESS: 0x0
After:
u-boot=> mmc partconf 2 1 1 0 && mmc partconf 2
EXT_CSD[179], PARTITION_CONFIG:
BOOT_ACK: 0x1
BOOT_PARTITION_ENABLE: 0x1 (boot0)
PARTITION_ACCESS: 0x0 (user)
u-boot=> mmc partconf 2 1 boot1 0 && mmc partconf 2
EXT_CSD[179], PARTITION_CONFIG:
BOOT_ACK: 0x1
BOOT_PARTITION_ENABLE: 0x2 (boot1)
PARTITION_ACCESS: 0x0 (user)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use the log subsystem instead of dev, to avoid including function names
in the code.
The CONFIG_LOGF_FUNC option can be used to enable the function name.
Update 'enhanced size' to use hex since this is the U-Boot default and
more natural for the large numbers involved.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
The code makes quite a few uses of __func__ which puts the function
name into the resulting SPL image. Use the log subsystem instead, to
reduce size.
The CONFIG_LOGF_FUNC option can be used to enable the function name.
Use lower-case hex for the status output in sdhci_transfer_data(), to
match sdhci_send_command()
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Fix most of checkpatch warnings and other obvious style issues.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Reduce U-Boot footprint by reusing dev->name as a driver's displayed
name. This changes boot device name (and "mmc info" output) from "EXYNOS
DWMMC" to something like "mmc@12100000".
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
add_dwmci() is already calling dwmci_setup_cfg() internally, there is no
needed to call dwmci_setup_cfg() again in case when add_dwmci() is used
(for non-DM cases). Fix it by calling dwmci_setup_cfg() only in DM
cases, when add_dwmci() wasn't called. Also, this assignment:
host->mmc = &plat->mmc;
is wrong in non-DM case when add_dwmci() was called, as it's creating
mmc object internally. Fix that by pulling that assignment into DM case,
when add_dwmci() isn't called.
While at it, add also this missing assignment:
host->mmc->dev = dev;
Fixes: 3537ee879e ("mmc: exynos_dw_mmc: support the Driver mode for Exynos")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
There is no logical sense to split the initialization code between
multiple functions. Pull both do_dwmci_init() and
exynos_dwmci_core_init() into exynos_dwmmc_probe() to make the code more
simple and obvious.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add the compatible entry and corresponding chip data for Exynos7
compatible chips, which covers modern ARM64 based Exynos chips. They
have some differences w.r.t. old ARM32 Exynos chips:
- CLKSEL register offset is different
- 64-bit IDMAC descriptor and 64-bit IDMAC registers are used
(implemented in dw_mmc core driver)
In terms of the driver implementation, the CIU clock is obtained via CCF
framework (as opposed to ad-hoc clock driver implementation for ARM32
chips).
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
By now exynos_dw_mmc driver was relying on the correct CIU clock
frequency being set on driver init. But dw_mmc core is actually trying
to change CIU clock rate dynamically, on init and in set_ios() callback,
which it's requesting via host->get_mmc_clk() callback (the name is
misleading: although it's called "get_mmc_clk()", it can actually
request both get and set operations). Implement setting the requested
rate for CIU clock in Exynos driver to achieve the correct dw_mmc core
driver operation at all times. DDR mode requires the clock to be twice
as fast (when 8 bit bus is used), so handle this too, to make DDR
function properly.
This change makes the eMMC throughput on E850-96 board twice as fast.
That's because "clock-frequency" is set to 800 MHz in E850-96 device
tree, but for DDR52 mode it should be 416 MHz (and TRM states it should
be 400 MHz for DDR50/8bit mode). The dw_mmc core is requesting 52 MHz
bus_hz for DDR52 mode, and DDR+8bit mode means it should be x2 fast, so:
f_ciu = 2 * ciu_div * f_bus = 2 * 4 * 52e6 = 416 MHz,
where f_ciu - freq of clock fed to DW MMC block from CMU (SDCLKIN), Hz
f_bus - freq of clock fed to the card (CCLKIN), Hz
ciu_div - value of internal divider (in DW MMC block).
Another way to work that around would be overriding the
"clock-frequency" property in corresponding dts. But setting the clock
frequency dynamically as it's done here looks much neater.
This implementation follows what's done in Linux kernel dw_mmc-exynos
driver in .set_ios() callback for MMC_TIMING_MMC_DDR52 case.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
DDR timing values should be defined in "samsung,dw-mshc-ddr-timing" dts
property, and used when DDR MMC mode is selected. Read that value from
dts and use it. If it's not available, use SDR timing values instead.
This change is following upstream Linux kernel implementation.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
host->quirks field is only used internally in exynos_dw_mmc.c driver.
To avoid cluttering the scope of struct dwmci_host, move quirks field
into Exynos driver's chip data, where it can be statically defined.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Instead of using non-standard "bus_hz" dts property, read common
"clock-frequency" property used in upstream Linux kernel. It's safe to
do so, as "clock-frequency" property was already added to corresponding
nodes in all affected Exynos device tree files.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Instead of using non-standard "samsung,bus-width" dts property, read
common "bus-width" property used in upstream Linux kernel. It's safe to
do so, as "bus-width" property was already added to corresponding nodes
in all affected Exynos device tree files.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Some chips like Exynos4412 have fixed internal CIU clock divider.
Instead of reading it from non-standard "div" dts property, store its
value in the driver internally, in static chip data associated with
corresponding compatible. This makes it possible to avoid using
host->div for storing it, so the latter can be removed safely. Also
create a helper function called exynos_dwmmc_get_ciu_div() for getting
the current div value: in case the fixed div is provided in the chip
data it will be used, otherwise the current div value is being read from
CLKSEL register.
The insights for this change were taken from dw_mmc-exynos.c driver in
Linux kernel.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
CLKSEL register offset may vary between different Exynos chips, e.g. on
ARM64 vs ARM32 chips. Provide a way to specify its offset value for each
compatible instead of hard-coding its value in read/write calls.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The obsolete "samsung,timing" dts property is now split into
"samsung,dw-mshc-ciu-div" (for holding the internal DW MMC divider
value) and "samsung,dw-mshc-sdr-timing" (for actual timing values) in
upstream Linux kernel. Rework the driver to make use of new properties
instead of the old one. All affected dts files were already updated
accordingly.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Update the driver to use livetree API instead of FDT one.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
exynos_dwmci_get_config() is called from the probe function and used to
read data from device tree. Make use of .of_to_plat driver callback
instead, and convert exynos_dwmci_get_config() to match its signature.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
New Exynos chips should implement clock drivers using CCF framework. In
that case corresponding CCF functions can be used to get/set the clock
rates. Moreover, already existing get_mmc_clk() and set_mmc_clk() calls
are only implemented for CONFIG_CPU_V7A (i.e. ARM32 chips). In case of
ARM64 chips that config option is not defined, so build will crash on
linking stage, with errors like these:
ld: drivers/mmc/exynos_dw_mmc.o:
in function `exynos_dwmci_get_sclk':
undefined reference to `get_mmc_clk'
ld: drivers/mmc/exynos_dw_mmc.o:
in function `exynos_dwmci_set_sclk':
undefined reference to `set_mmc_clk'
Fix that issue by using CCF clocks API on ARM64 platforms for getting
and setting the source clock (sclk = SDCLKIN = CIU) rate. To implement
this, first extract the existing ARM32 clock control code into helper
functions with more generic signatures to abstract getting/setting the
sclk rate. Then add CCF clock support to those functions for ARM64
platforms.
Fixes: a082a2dde0 ("EXYNOS5: DWMMC: Added FDT support for DWMMC")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Pinmux configuration on ARM64 platforms must be performed during startup
in pinctrl driver using info from device tree. exynos_pinmux_config()
and pinmux_decode_periph_id() are only available on ARM32 platforms, so
don't call those functions on ARM64 platforms. Instead of the latter
function, use "non-removable" property from device tree to derive the
dev_index value.
This fixes next linking errors on ARM64 platforms:
ld: drivers/mmc/exynos_dw_mmc.o:
in function `exynos_dwmci_get_config':
undefined reference to `pinmux_decode_periph_id'
ld: drivers/mmc/exynos_dw_mmc.o:
in function `do_dwmci_init':
undefined reference to `exynos_pinmux_config'
Fixes: a082a2dde0 ("EXYNOS5: DWMMC: Added FDT support for DWMMC")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
In case of CONFIG_DM_MMC, host->priv actually holds (struct udevice *),
and not (struct dwmci_exynos_priv_data *). This makes *priv pointer
invalid and may lead to Synchronous Abort during its dereference later
in exynos_dwmci_board_init(). Fix it by extracting
exynos_dwmmc_get_priv() helper from exynos_dwmci_clksel() and using it
for getting the private data in exynos_dwmci_board_init()
Fixes: 3537ee879e ("mmc: exynos_dw_mmc: support the Driver mode for Exynos")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Getting the base address with outdated fdtdec_get_addr() API and further
casting it to (void *) leads to next build warning on ARM64 platforms:
In function 'exynos_dwmci_get_config':
warning: cast to pointer from integer of different size
[-Wint-to-pointer-cast]
host->ioaddr = (void *)base;
Use livetree API instead (dev_read_addr_ptr()), which handles this
correctly.
Fixes: a082a2dde0 ("EXYNOS5: DWMMC: Added FDT support for DWMMC")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Fix most of checkpatch warnings and other obvious style issues.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Replace fifoth_val property with its fifo-depth counterpart in all DW
MMC drivers. fifo-depth is a common property used in upstream Linux
kernel. The FIFOTH register value will be calculated using fifo-depth
value in DW MMC core (dw_mmc.c). This change reduces code duplication in
platform drivers, and pulls common FIFOTH register value calculation
into core dw_mmc driver where it belongs.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Some DW MMC blocks (e.g. those on modern Exynos chips) support 64-bit
DMA addressing mode. 64-bit DW MMC variants differ from their 32-bit
counterparts:
- the register layout is a bit different (because there are additional
IDMAC registers present for storing upper part of 64-bit addresses)
- DMA descriptor structure is bigger and different from 32-bit one
Introduce all necessary changes to enable support for 64-bit DMA capable
DW MMC blocks. Next changes were made:
1. Check which DMA address mode is supported in current IP-core
version. HCON register (bit 27) indicates whether it's 32-bit or
64-bit addressing. Add boolean .dma_64bit_address field to struct
dwmci_host and store the result there. dwmci_init_dma() function is
introduced for doing so, which is called on driver's init.
2. Add 64-bit DMA descriptor (struct dwmci_idmac64) and use it in
dwmci_prepare_desc() in case if .dma_64bit_address field is true.
A new dwmci_set_idma_desc64() function was added for populating that
descriptor.
3. Add registers for 64-bit DMA capable blocks. To make the access to
IDMAC registers universal between 32-bit / 64-bit cases, a new
struct dwmci_idmac_regs (and corresponding host->regs field) was
introduced, which abstracts the hardware by being set to
appropriate offset constants on init. All direct calls to IDMAC
registers were correspondingly replaced by accessing host->regs.
4. Allocate and use 64-bit DMA descriptors buffer in case when IDMAC
is 64-bit capable. Extract all the code (except for the IDMAC
descriptors buffer allocation) from dwmci_send_cmd() to
dwmci_send_cmd_common(), so that it's possible to keep IDMAC
buffer (either 32-bit or 64-bit) on stack during send_cmd routine.
The insights for this implementation were taken from Linux kernel DW MMC
driver.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Prepare for adding 64-bit IDMAC descriptors by renaming current 32-bit
descriptor and its fields accordingly. While at it, make use of
virt_to_phys() to make it more obvious in which places the physical
addresses have to be used.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Make dwmci_prepare_data() function easier to read by extracting the
preparation of IDMAC descriptor into a dedicated function.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Make dwmci_send_cmd() easier to read by moving the DMA transfer handling
code into a dedicated function.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
FIFO data transfer is implemented as quite a massive chunk of code.
Extract it into a dedicated function to make dwmci_data_transfer()
easier to read and reduce the indentation level of the code.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Extract the clock divider update into dwmci_update_div() function. It's
a procedure recommended in TRM, so it's better to keep it in a dedicated
function to make the code clearer.
While at it also extract the clock control code into a separate routine
to avoid code duplication in dwmci_setup_bus().
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Move FIFO threshold initialization into a separate function to make
dwmci_init() more readable.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Waiting for data busy is a logically separate operation and should be
implemented as a separate routine. Follow Linux kernel example and
extract it from dwmci_send_cmd(). This way it doesn't clutter
dwmci_send_cmd() function, and can be reused later in other cases.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
struct idmac is only used in dw_mmc.c, so move it there from dwmmc.h to
avoid cluttering the interface in the header.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Hosts capable of 8-bit can also do 4 bits, fix use of 4-bit mode when
8-bit mode is supported.
This fixes use of 1-bit mode with SD NAND on ROCK Pi S using the DT in
v6.11-rc1 that chage to use 8-bit bus to also support eMMC. With this
4-bit mode is used with SD NAND and 8-bit mode with eMMC, same as in
Linux kernel.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The ARASAN MMC controller on Keystone 3 class of devices need the SDCD
line to be connected for proper functioning.
In cases where this can't be connected, add a quirk to force the
controller into test mode and set the TESTCD bit. Use the flag
"ti,fails-without-test-cd", to implement this above quirk when required.
Additionally, this quirk also avoids waiting for the controller debounce
time.
This commit is similar to linux kernel commit c7666240ec76
("drivers: mmc: sdhci_am654: Add the quirk to set TESTCD bit").
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Christian Marangi <ansuelsmth@gmail.com> says:
This is an initial series that have all the initial trivial
fixes required for usage of OF_UPSTREAM for the mediatek SoC
This also contains the pcie-gen3 driver and the required tphy
support driver to make it work.
Subsequent series will follow with conversion of the mtk-clk
to permit usage of OF_UPSTREAM and upstream clk ID.
MT7981, MT7986 and MT7988 migration to upstream clock ID
is complete and working on MT7623.
Series CI tested with PR: https://github.com/u-boot/u-boot/pull/590
Add support for upstream linux clock and map U-Boot property to the one
use in upstream linux where supported.
Also add handling for the use_internal_cd that on upstream is hardcoded
enabled on mt7620.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add missing newline character and also add the return code of
regulator_set_value() to the output.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
common:
- spl: Introduce SoC specific init function
xilinx:
- Enable FF-A and NVMEM
- Rename spl_board_init() to spl_soc_init()
zynqmp:
- DT alignments
- Enable reset from SPL
- Enable USB3 for KD240
- Align multiboot register on Kria for proper reboot
- Allow multiboot environment write even in saved environment
- Move zynqmp commands from board/ to arch/
- Clean up xilinx_zynqmp.h
versal:
- Do not prioritize boot device if driver is not enabled
versal-net:
- Setup location for redundant variables in SPI
versal2:
- Add support for new SOC
mmc:
- Fix tap delay for SD on Versal NET
spi:
- Add SPI_NOR_OCTAL_READ flag for mx66uw2g345gx0 flash part
gpio:
- Cover MODEPIN firmware dependency
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZnBfewAKCRDKSWXLKUoM
Ib/7AJ0cn3q7lMpxbSbRj33oftI8Vy8+owCeN35Nl8TN9l/DHbfusER4uVfnOVw=
=YMIB
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2024.10-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
AMD/Xilinx changes for v2024.10-rc1
common:
- spl: Introduce SoC specific init function
xilinx:
- Enable FF-A and NVMEM
- Rename spl_board_init() to spl_soc_init()
zynqmp:
- DT alignments
- Enable reset from SPL
- Enable USB3 for KD240
- Align multiboot register on Kria for proper reboot
- Allow multiboot environment write even in saved environment
- Move zynqmp commands from board/ to arch/
- Clean up xilinx_zynqmp.h
versal:
- Do not prioritize boot device if driver is not enabled
versal-net:
- Setup location for redundant variables in SPI
versal2:
- Add support for new SOC
mmc:
- Fix tap delay for SD on Versal NET
spi:
- Add SPI_NOR_OCTAL_READ flag for mx66uw2g345gx0 flash part
gpio:
- Cover MODEPIN firmware dependency
I can't see any way how tap delays are setup on Versal NET platform because
xlnx,versal-8.9a compatible string is also used there but driver is not
letting to setup tap delays. Not sure if versal_iclk_phases[] is also valid
for Versal NET but the patch is made to investigate it.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/e535cfc1a59b5146a5c9a3ab389dc770de80440c.1713427490.git.michal.simek@amd.com
At this point in the DM migration, all platforms enable DM. BLK requires
DM. Make BLK "def_bool y" in the cases it had been "default y" to make
this clearer. Now remove the symbol requirement from other places as it
is redundant here.
Signed-off-by: Tom Rini <trini@konsulko.com>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d, reversing
changes made to 2ee6f3a5f7.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The constraints on the MMC_SUPPORTS_TUNING symbol can easily be
expressed in Kconfig (with the addition of SPL_MMC_SUPPORTS_TUNING).
Furthermore, in order to remove <common.h> from the MMC subsystem, the
way this symbol is used today needs to be changed in order to continue
functioning.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently, only the receive delay is configured while the transmit delay
is not set, which may result in errors when writing to the file. This issue
can be resolved by setting PHY_TX_SRC_INVERT to SDHCI_PHY_TX_RX_DLY.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Judith Mendez <jm@ti.com> says:
The following patch series includes a MMC tuning algorithm
fix according to the following published paper [0].
This seris also includes fixes for OTAP/ITAP delay values
in j721e_4bit_sdhci_set_ios_post and for HS400 mode.
For DDR52 mode, also set ENDLL=1 and call am654_sdhci_setup_dll()
instead of am654_sdhci_setup_delay_chain() according to
device datasheet[1].
[0] https://www.ti.com/lit/an/spract9/spract9.pdf
[1] https://www.ti.com/lit/ds/symlink/am62p.pdf
At HS400 mode the ITAPDLY value is that from High Speed mode
which is incorrect and may cause boot failures.
The ITAPDLY for HS400 speed mode should be the same as ITAPDLY
as HS200 timing after tuning is executed. Add the functionality
to save ITAPDLY from HS200 tuning and save as HS400 ITAPDLY.
Fixes: c964447ea3 ("mmc: am654_sdhci: Add support for input tap delay")
Signed-off-by: Judith Mendez <jm@ti.com>
According to the device datasheet [0], ENDLL=1 for
DDR52 mode, so call am654_sdhci_setup_dll() and write
itapdly after since we do not carry out tuning.
[0] https://www.ti.com/lit/ds/symlink/am62p.pdf
Fixes: c964447ea3 ("mmc: am654_sdhci: Add support for input tap delay")
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Set itap_del_ena if ITAPDLY is found in DT or if the tuning
algorithm was executed and found the optimal ITAPDLY. Add the
functionality to save ITAPDLYENA that can be referenced later
by storing the bit in array itap_del_ena[].
Signed-off-by: Judith Mendez <jm@ti.com>
U-Boot is failing to boot class U1 UHS SD cards due to incorrect
OTAP and ITAP delay select values. Update OTAP and ITAP delay select
values from DT.
Fixes: c7d106b4eb ("mmc: am654_sdhci: Update output tap delay writes")
Signed-off-by: Nitin Yadav <n-yadav@ti.com>
Signed-off-by: Judith Mendez <jm@ti.com>
Currently the sdhci_am654 driver only supports one tuning
algorithm which should be used only when DLL is enabled. The
ITAPDLY is selected from the largest passing window and the
buffer is viewed as a circular buffer.
The new tuning algorithm should be used when the delay chain
is enabled; the ITAPDLY is selected from the largest passing
window and the buffer is not viewed as a circular buffer.
This implementation is based off of the following paper: [1].
Also add support for multiple failing windows.
[1] https://www.ti.com/lit/an/spract9/spract9.pdf
Fixes: a759abf569 ("mmc: am654_sdhci: Add support for software tuning")
Signed-off-by: Judith Mendez <jm@ti.com>
The commit 2cc6cde647 ("mmc: rockchip_sdhci: Limit number of blocks
read in a single command") introduced a limit of number of blocks to
read to fix a Data End Bit Error on RK3568 and RK3588. This had a side
affect of significant slowing down reading FIT from eMMC.
After the commit 6de9d7b2f1 ("rockchip: rk35xx: Enable eMMC HS200 mode
by default") the limit of number of blocks to read workaround is no
longer necessary and at HS200+ a Data End Bit Error is no longer
happening using PIO mode.
Change this limitation to allow reading more than 4 blocks with a single
CMD18 command in PIO mode at HS200+ speed, keep using the 4 blocks
limitation when loadig FIT from eMMC at lower speed than HS200.
Fixes: 2cc6cde647 ("mmc: rockchip_sdhci: Limit number of blocks read in a single command")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Currently fetching files bigger that cause a data transfer greater than
U16_MAX fails.
The reason is that the specification defines the datalength register
as a 16 bit wide register, but in u-boot it is used as if it is an
32 bit register. Therefore values greater than U16_MAX cause an
infinite loop inside u-boot. U-boot expects to get more data from
interface/hardware then it will ever get and therefore inifintely waits
for more data that will never come.
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
According to the SD Host Controller Simplified Specification v4.20,
the multiplier value M is one more than the Clock Multiplier field.
Copied code from Linux project. drivers/mmc/host/sdhci.c line 4405
Signed-off-by: cmachida <curtis.machida@intel.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
The linux commit f722e650d965 ("mmc: core: add support for disabling
HS400 mode via DT") added support for a no-mmc-hs400 prop.
Add support for the no-mmc-hs400 prop to disable HS400 host caps.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
eMMC nodes in linux device tree files typically only contain a mmc-hs400
prop to signal support for both HS400 and HS200. However, U-Boot require
an explicit mmc-hs200 prop to signal support for the HS200 mode.
Fix this by follow linux and imply HS200 cap when HS400 cap is signaled
using a mmc-hs400 prop.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Quentin Schulz <quentin.schulz@theobrma-systems.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Some arm64 platforms may include SDIO host controllers that
only support 32-bit ADMA. While the Linux kernel detects which
size is supported and adjusts the descriptor size used dynamically,
the previous u-boot implementation statically selected between the
two depending on whether DMA_ADDR_T_64BIT was defined. Because the
static selection is already in place and effective for most platforms,
this patch logically separates "64 bit addresses are used for DMA on
this platform" and "64 bit addresses are used by the SDIO host
controller for ADMA" in order to support the small number of platforms
where these statements are not equivalent.
Using 32 bits is opt-in and existing 64 bit platforms should be
unaffected by this change.
Co-developed-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Co-developed-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Greg Malysa <greg.malysa@timesys.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add this hook so that it can be overridden with driver specific
implementations. We also let the original sdhci_adma_write_desc()
accept &desc so that the function can set its new value. Then export
the function so that it could be reused by driver's specific
implementations.
The above is a port of Linux kernel commit 54552e4948cbf
In addition, allow drivers to allocate their own ADMA descriptor
tables if additional space is required.
Finally, fix the assignment of adma_addr to fix compiler warning
on 64-bit platforms that still use 32-bit DMA addressing.
Co-developed-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Co-developed-by: Greg Malysa <greg.malysa@timesys.com>
Signed-off-by: Greg Malysa <greg.malysa@timesys.com>
Signed-off-by: Ian Roberts <ian.roberts@timesys.com>
The addresses were mistakenly swapped. Put them right.
Reported-by: Sumit Garg <sumit.garg@linaro.org>
Fixes: a737d8962cae ("mmc: msm_sdhci: correct vendor_spec_cap0 register for v5")
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
We currently default to the lowest rate but this actually doesn't work
on most platforms. Default to the HS400 speed instead which is most
common on Qualcomm platforms.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
using fdtdec_* functions is incompatible with OF_LIVE and generally
offers a less friendly interface. Update to use dev_read_* functions
instead.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The V4 and V5 controllers have quite varied register layouts. Inherit
the register offsets and naming from the Linux driver. More version
specific offsets can be inherited from Linux as needed.
Fixes: 364c22a ("mmc: msm_sdhci: Add SDCC version 5.0.0 support")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
When building with AARCH64 defconfig, we got warnings, fix them.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The value defaults to 0 and is ignored by dw_mmc code, so the other
users are not affected.
Setting this explicitly fixes some weird reading error found on Hi3798MV200.
Fixes: 8a5dc8140e ("mmc: hi6220_dw_mmc: add compatible for HC2910 support")
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This can avoid hardcoding a clock rate in driver. Also can enable the
clocks and deassert the resets if the pre-bootloader does not do this
for us.
Currently only enabled for Hi3798MV200.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Place the SDR104/HS200/HS400 checks into the mmc_deinit() and always
call it. This simplifies the code and removes ifdeffery. No functional
change is expected.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Do not access SCC when sending commands during tuning operation as that
will disrupt the tuning operation. The tuning operation is adjusting the
SCC settings itself in execute_tuning callback.
When renesas_sdhi_execute_tuning() is called by the MMC core code, a loop
which consists of renesas_sdhi_prepare_tuning(), mmc_send_tuning() and
renesas_sdhi_compare_scc_data() iterates over each SCC tuning tap.
The renesas_sdhi_prepare_tuning() configures the SCC tuning tap number into
hardware, mmc_send_tuning() triggers transfer of tuning block which depends
on the bus mode for which the bus is currently being tuned, this information
is supplied by the MMC core code, and finally renesas_sdhi_compare_scc_data()
tests the received tuning block for validity.
Because renesas_sdhi_prepare_tuning() configures the SCC tuning tap into
the hardware to fit the tuning operation, mmc_send_tuning() which triggers
command transfer using renesas_sdhi_send_cmd() must not manipulate with
the SCC in any way. Currently renesas_sdhi_send_cmd() does unconditionally
call renesas_sdhi_check_scc_error(), which may adjust the SCC tuning tap
position by writing RENESAS_SDHI_SCC_TAPSET, which would overwrite the
required tuning configuration set by renesas_sdhi_prepare_tuning() and
disrupt the tuning operation.
Fix this by skipping the renesas_sdhi_check_scc_error() call in case the
MMC subsystem is in tuning state. This way, the SCC settings are left
unmodified by command transfer during tuning operation.
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Tested-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Set generic mmc->tuning flag when performing tuning to indicate
this condition to drivers. Drivers may use this to bypass various
checks during tuning.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This hs400_tuning is a flag, make it bool. No functional change.
This will be useful in the following patch, which adds another
more generic flag, where the compiler can better use the space
now reserved for the u8 to store more flags in it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
