We should avoid overwhelming users with non-essential messages.
'Register NbrPorts' is a debug message for EHCI. Do the same for XHCI.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Marek Vasut <marek.vasut@mailbox.org>
CONFIG_USB_EHCI_PCI cannot work without CONFIG_PCI.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Marek Vasut <marek.vasut@mailbox.org>
All instances of the U_BOOT_DRIVER must use a unique name or they will
lead to link time failures due to name space conflicts when both are
present. Most of the XHCI drivers follow pattern of xhci_xxx in their
name, but a few used "usb_xhci". Change these to follow the pattern of
the rest of the XHCI glue drivers.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Since the EHCI USB driver is shared across i.MX91, i.MX93, i.MX94, and
i.MX95, the condition check is updated to use IMX9.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Marek Vasut <marek.vasut@mailbox.org>
A variety of Qualcomm features/fixes for this cycle, notably with a few
new platforms gaining support:
* Initial support for SDM670 (similar to SDM845), SM6350, and SM7150
platforms is added
* USB and UART issues on MSM8916 are addressed (improving stability/
reliability)
* Firmware loading is implemented for the GENI serial engine, this is
used on some platforms to load firmware for i2c/spi/uart to work
Some additional patches like binman support for building MBN files still
need some additional work.
CI: 8ef6ac07b3/pipelines
The UCLASS_USB device is removed and rebound each time you run "usb stop"
followed by "usb start", or when you switch between USB device and USB host
mode. Unfortunately, this causes issues with the current ehci-msm driver:
In ehci_usb_remove() we call generic_shutdown_phy(), but at that point the
ULPI PHY we registered in ehci_usb_of_bind() was already removed again by
the DM core.
Fix this by adding a UCLASS_NOP driver that keeps the PHY driver bound
permanently, and then just re-probe the actual USB part.
Reported-by: Jianfeng Zhu <JianfengA.Zhu@sony.com>
Closes: https://lore.kernel.org/u-boot/OSQPR04MB774067EBEEADD714EFE18C2A90882@OSQPR04MB7740.apcprd04.prod.outlook.com/
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Acked-by: Caleb Connolly <caleb.connolly@linaro.org>
Tested-by: Sam Day <me@samcday.com>
Link: https://patch.msgid.link/20250407-ehci-msm-fixes-v1-6-f8b30eb05d07@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
ehci_unregister() already clears the CMD_RUN bit with more careful checks.
It also ensures that we only do this in case we were actually in USB host
(rather than USB device) mode. It's not clear what the extra register
writes in the Qualcomm-specific ehci-msm driver are supposed to do, so just
drop them.
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Acked-by: Caleb Connolly <caleb.connolly@linaro.org>
Tested-by: Sam Day <me@samcday.com>
Link: https://patch.msgid.link/20250407-ehci-msm-fixes-v1-5-f8b30eb05d07@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
The enable order for the clocks does not matter much, we just need to
enable all the USB clocks. Use the clk bulk helpers to simplify the code.
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Acked-by: Caleb Connolly <caleb.connolly@linaro.org>
Tested-by: Sam Day <me@samcday.com>
Link: https://patch.msgid.link/20250407-ehci-msm-fixes-v1-4-f8b30eb05d07@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
We need the USB clocks to do accesses like
wait_for_bit_le32(&ehci->usbcmd, CMD_RESET, ...)
so we should disable them only after all of them are done.
At the moment this works only because the clock driver doesn't actually
disabling these clocks in U-Boot.
Fixes: 9b3a9f896e66 ("ehci: msm: bring up iface + core clocks")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Acked-by: Caleb Connolly <caleb.connolly@linaro.org>
Tested-by: Sam Day <me@samcday.com>
Link: https://patch.msgid.link/20250407-ehci-msm-fixes-v1-3-f8b30eb05d07@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
These are unused.
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Acked-by: Caleb Connolly <caleb.connolly@linaro.org>
Tested-by: Sam Day <me@samcday.com>
Link: https://patch.msgid.link/20250407-ehci-msm-fixes-v1-2-f8b30eb05d07@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
dev_read_addr_ptr() returns a null pointer on error, not FDT_ADDR_T_NONE.
Fixes: 2be1130a9305 ("usb: ehci-msm: Use dev interface to get device address")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Acked-by: Caleb Connolly <caleb.connolly@linaro.org>
Tested-by: Sam Day <me@samcday.com>
Link: https://patch.msgid.link/20250407-ehci-msm-fixes-v1-1-f8b30eb05d07@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
The variable node is assigned to the return value of a function that
returns an int. It is tested for being negative and then passed as an
argument to a function that takes an int. So 'node' should not be
declared as unsigned. Correct it.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
When a variable needs a null check before it is dreferenced ensure that
this is done even in the case of assignment on declaration. This was not
happening for lurb_priv so correct it.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
THe variable node is assigned to the return value of a function that
returns an int. It is tested for being negative and then passed as an
argument to a function that takes an int. So 'node' should not be
declared as unsigned. Correct it.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut@mailbox.org>
A few of the USB host drivers cannot build without access to some
platform specific header files. Express those requirements in Kconfig as
well.
Reviewed-by: Marek Vasut <marek.vasut@mailbox.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable support for Exynos850 SoC in DWC3 host glue layer driver.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut@mailbox.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
When the usb node is defined dr_mode="otg" ehci_usb_phy_mode() is called
to determine the mode from status registers.
The IMX95RM does not currently define the USBNC STATUS register but it is
assumed to be an omission as the first three registers are defined.
It has been expirimentally verified that the USBNC_PHY_STATUS register
at offset 0x23C bit4 (USBNC_PHYSTATUS_ID_DIG) reads 0 when USB_ID is GND
and 1 when floating.
Use is_imx9() as this driver works for i.MX91, i.MX93 and i.MX95 and all
of these determine the role based on the USBNC_PHY_STATUS register.
Fixes: 801b5fafd35d "(usb: ehci-mx6: Add i.MX95 support")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Updates all instances of uint8_t, uint16_t, and uint32_t to u8, u16, and
u32 respectively, ensuring consistent use of kernel-preferred types and
resolving checkpatch.pl warnings.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Junhui Liu <junhui.liu@pigmoral.tech>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20250110-dwc2-dev-v4-8-987f4fd6f8b2@pigmoral.tech
Signed-off-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
This patch merges flush and reset logic for both host and gadget code
into a common set of functions, reducing duplication. It also adds support
for the updated reset logic to compatible with core version since v4.20a.
This patch mainly refers to the patch in the kernel.
link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=65dc2e725286106f99c6f6b78e3d9c52c15f3a9c
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Junhui Liu <junhui.liu@pigmoral.tech>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20250110-dwc2-dev-v4-7-987f4fd6f8b2@pigmoral.tech
Signed-off-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Some macros are shared between host and gadget code, causing duplicated
definitions. Move DWC2 macro definitions from host and gadget code into a
common header to reduce duplication.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Junhui Liu <junhui.liu@pigmoral.tech>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20250110-dwc2-dev-v4-6-987f4fd6f8b2@pigmoral.tech
Signed-off-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Update the DWC2 macros to match those used in the Linux kernel, making
it easier to synchronize updates with kernel. Also removed some unused
macros to cleanup the code.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Junhui Liu <junhui.liu@pigmoral.tech>
Link: https://lore.kernel.org/r/20250110-dwc2-dev-v4-5-987f4fd6f8b2@pigmoral.tech
Signed-off-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Use FIELD_PREP, FIELD_GET, BIT, and GENMASK macros to standardize bit
manipulation across the DWC2 code, improving readability and
maintainability without altering functionality.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Junhui Liu <junhui.liu@pigmoral.tech>
Link: https://lore.kernel.org/r/20250110-dwc2-dev-v4-4-987f4fd6f8b2@pigmoral.tech
Signed-off-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
The loop used to calculate HBstLen for extern DMA mode does not produce
the correct result according to the datasheet [1]. Replacing that loop
with a direct calculation using LOG2 to correctly assign the burst length
in the GAHBCFG register for external DMA mode.
[1] https://rockchip.fr/RK312X%20TRM/chapter-26-usb-otg-2-0.pdf#page=24
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Junhui Liu <junhui.liu@pigmoral.tech>
Link: https://lore.kernel.org/r/20250110-dwc2-dev-v4-3-987f4fd6f8b2@pigmoral.tech
Signed-off-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
The ULPI_UTMI_SEL bit in the DWC2 driver was set incorrectly. According
to the datasheet [1], this bit should be set to 0 for UTMI interface and 1
for ULPI interface. The existing code had this logic reversed,
causing the interface selection to be incorrect.
This commit corrects the ULPI_UTMI_SEL bit setting to match the
datasheet's description. Referencing the kernel's code [2] also confirms
this fix.
[1] https://rockchip.fr/RK312X%20TRM/chapter-26-usb-otg-2-0.pdf#page=30
[2] https://github.com/torvalds/linux/blob/v6.13-rc3/drivers/usb/dwc2/core.c#L1106
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Junhui Liu <junhui.liu@pigmoral.tech>
Link: https://lore.kernel.org/r/20250110-dwc2-dev-v4-2-987f4fd6f8b2@pigmoral.tech
Signed-off-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
The same registers are accessed in both the otg and gatet drivers of
dwc2, and these registers are repeatedly defined in these two parts.
Extract register definitions into a common header file to reduce
redundancy and make the code more maintainable.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Junhui Liu <junhui.liu@pigmoral.tech>
Link: https://lore.kernel.org/r/20250110-dwc2-dev-v4-1-987f4fd6f8b2@pigmoral.tech
Signed-off-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
The way we enable ULPI support today isn't something that should work.
The "optional" keyword in a choice statement is not a documented
feature. To make this work in a supported way, make USB_ULPI something
we ask about if USB_HOST is set. Next, we move the choice of what
viewer to use to be after the framework portion and to depend on that.
We then borrow a few words from the top-level README to make the help
text here clearer. Finally we make the Qualcomm driver select ULPI as
it's required and we make the tegra driver not duplicate a check that
Kconfig now handles for us.
Signed-off-by: Tom Rini <trini@konsulko.com>
Use the uthread framework to initialize and scan USB buses in parallel
for better performance. The console output is slightly modified with a
final per-bus report of the number of devices found, common to UTHREAD
and !UTHREAD. The USB tests are updated accordingly.
Tested on two platforms:
1. arm64 QEMU on a somewhat contrived example (4 USB buses, each with
one audio device, one keyboard, one mouse and one tablet)
$ make qemu_arm64_defconfig
$ make -j$(nproc) CROSS_COMPILE="ccache aarch64-linux-gnu-"
$ qemu-system-aarch64 -M virt -nographic -cpu max -bios u-boot.bin \
$(for i in {1..4}; do echo -device qemu-xhci,id=xhci$i \
-device\ usb-{audio,kbd,mouse,tablet},bus=xhci$i.0; \
done)
2. i.MX93 EVK (imx93_11x11_evk_defconfig) with two USB hubs, each with
one webcam and one ethernet adapter, resulting in the following device
tree:
USB device tree:
1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Hub (480 Mb/s, 100mA)
| GenesysLogic USB2.1 Hub
|
+-3 Vendor specific (480 Mb/s, 350mA)
| Realtek USB 10/100/1000 LAN 001000001
|
+-4 (480 Mb/s, 500mA)
HD Pro Webcam C920 8F7CD51F
1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Hub (480 Mb/s, 100mA)
| USB 2.0 Hub
|
+-3 Vendor specific (480 Mb/s, 200mA)
| Realtek USB 10/100/1000 LAN 000001
|
+-4 (480 Mb/s, 500mA)
Generic OnLan-CS30 201801010008
Note that i.MX was tested on top of the downstream repository [1] since
USB doesn't work in the upstream master branch.
[1] https://github.com/nxp-imx/uboot-imx/tree/lf-6.6.52-2.2.0
commit 6c4545203d12 ("LF-13928 update key for capsule")
The time spent in usb_init() ("usb start" command) is reported on
the console. Here are the results:
| CONFIG_UTHREAD=n | CONFIG_UTHREAD=y
--------+------------------+-----------------
QEMU | 5628 ms | 2212 ms
i.MX93 | 4591 ms | 2441 ms
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
To prepare for the introduction of threads in the USB initialization
sequence, move code out of usb_init() into a new helper function:
usb_init_bus() and count the number of USB controllers initialized
successfully by using the DM device_active() function.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Tom Rini <trini@konsulko.com> says:
This series switches to always using $(PHASE_) in Makefiles when
building rather than $(PHASE_) or $(XPL_). It also starts on documenting
this part of the build, but as a follow-up we need to rename
doc/develop/spl.rst and expand on explaining things a bit.
Link: https://lore.kernel.org/r/20250401225851.1125678-1-trini@konsulko.com
It is confusing to have both "$(PHASE_)" and "$(XPL_)" be used in our
Makefiles as part of the macros to determine when to do something in our
Makefiles based on what phase of the build we are in. For consistency,
bring this down to a single macro and use "$(PHASE_)" only.
Signed-off-by: Tom Rini <trini@konsulko.com>
The USB XHCI code uses an implicit switch/case fallthrough to share code
for handling full speed and low speed transfers.
Add our "fallthrough;" statement-like macro before the second label in
the XHCI code, to avoid a warning when GCC's -Wimplicit-fallthrough
warning option is enabled.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The USB OCHI code uses an implicit switch/case fallthrough after checking
for valid descriptor IDs.
Add our "fallthrough;" statement-like macro before the default branch in
the OHCI code, to avoid a warning when GCC's -Wimplicit-fallthrough
warning option is enabled.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
STi will migrate to dwc3-generic driver, dwc3-sti-glue driver
can be removed.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20250130163547.512990-4-patrice.chotard@foss.st.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
i.MX95 uses the same USB IP as i.MX8MM. It can then reuse the ehci-mx6
driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
With the commit 4fcba5d556b4 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Based on 335799b7252a ("usb: dwc2: Use regulator_set_enable_if_allowed")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
With the commit 4fcba5d556b4 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Based on 335799b7252a ("usb: dwc2: Use regulator_set_enable_if_allowed")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
The correct spelling is R-Car, including the dash, update the usage.
Kconfig strings and comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Patrick Rudolph <patrick.rudolph@9elements.com> says:
Based on the existing work done by Simon Glass this series adds
support for booting aarch64 devices using ACPI only.
As first target QEMU SBSA support is added, which relies on ACPI
only to boot an OS. As secondary target the Raspberry Pi4 was used,
which is broadly available and allows easy testing of the proposed
solution.
The series is split into ACPI cleanups and code movements, adding
Arm specific ACPI tables and finally SoC and mainboard related
changes to boot a Linux on the QEMU SBSA and RPi4. Currently only the
mandatory ACPI tables are supported, allowing to boot into Linux
without errors.
The QEMU SBSA support is feature complete and provides the same
functionality as the EDK2 implementation.
The changes were tested on real hardware as well on QEMU v9.0:
qemu-system-aarch64 -machine sbsa-ref -nographic -cpu cortex-a57 \
-pflash secure-world.rom \
-pflash unsecure-world.rom
qemu-system-aarch64 -machine raspi4b -kernel u-boot.bin -cpu cortex-a72 \
-smp 4 -m 2G -drive file=raspbian.img,format=raw,index=0 \
-dtb bcm2711-rpi-4-b.dtb -nographic
Tested against FWTS V24.03.00.
Known issues:
- The QEMU rpi4 support is currently limited as it doesn't emulate PCI,
USB or ethernet devices!
- The SMP bringup doesn't work on RPi4, but works in QEMU (Possibly
cache related).
- PCI on RPI4 isn't working on real hardware since the pcie_brcmstb
Linux kernel module doesn't support ACPI yet.
Link: https://lore.kernel.org/r/20241023132116.970117-1-patrick.rudolph@9elements.com
Add support for the generic XHCI driver that contains no SoC
specific code. It can be used on platforms that simply work out
of the box, like on emulated platforms.
TEST: Booted on QEMU sbsa machine using the generic xhci driver.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Marek Vasut <marex@denx.de>
On some platforms with low USB throughput, tranfers
of huge files take a long time and watchdog timer can
expire resulting in hardware reset. Avoid this by
petting the watchdog as long as we have pending transfers.
Signed-off-by: Godfrey Mwangi <godmwan@microsoft.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Assorted Tegra enhancements. Merged with the recent XPL_BUILD changes,
resolve some whitespace issues and fix the name of the new apalis-tk1
env file by Tom.
Signed-off-by: Tom Rini <trini@konsulko.com>
Obtain USB phy configuration from phy node if such exists
and is enabled. If no, set default values.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Use PHASE_ as the symbol to select a particular XPL build. This means
that SPL_TPL_ is no-longer set.
Update the comment in bootstage to refer to this symbol, instead of
SPL_
Signed-off-by: Simon Glass <sjg@chromium.org>
Extend generic_setup_phy() parameter list with PHY mode and submode and
call generic_phy_set_mode() in generic_setup_phy(), so the generic PHY
setup function can configure the PHY into correct mode before powering
the PHY up.
Update all call sites of generic_setup_phy() as well, all of which are
USB host related, except for DM test which now behaves as a USB host
test.
Note that if the PHY driver does not implement the .set_mode callback,
generic_phy_set_mode() call returns 0 and does not error out, so this
should not break any existing systems.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Just like drivers/usb/host/ehci-mx6.c, add a default for
drivers/usb/host/ehci-mx5.c.
The motivation for doing this is to remove CFG_MXC_USB_PORTSC
from board config files.
All the mx5 boards, with the exeption of mx51evk, define
CFG_MXC_USB_PORTSC as:
#define CFG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
So move this definition as a default into ehci-mx5.c.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This is only used by devkit3250 which is being removed. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
u-boot-dfu-20240711
Usb gadget:
- A welcome cleanup: epautoconf workaround is dropped to use
.match_ep() instead
- Introduce handle_interrupts() op for USB_GADGET_GENERIC, which
allows a per-driver interrupt handling
Fastboot:
- Fix mssing include when building with TCP only
Replace one type of terrible code formatting with a different
type of terrible code formatting. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Hector Martin <marcan@marcan.st>
