meson_gpio_get() always assumes gpio is configured to input mode. This
is incorrect and breaks `gpio toggle` command:
gpio: pin aobus-banks2 (gpio 2) value is 0
Warning: value of pin is still 1
Fix it by adding the logic to handle both input and output mode.
Fixes: 2009a8d03fe5 ("pinctrl: meson: add GPIO support")
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250617-meson_ppinctrl-v3-1-218d9321a8d2@outlook.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Define the daisy register offset for i.MX94 at 0x608 within the iomuxc
register space. This enables correct pad selection for daisy chain
configuration on i.MX94 platforms.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
It's common that UARTs are bound and probed before U-Boot relocation, in
which case the UART's pincontroller and pinconfig must be probed first.
Let's apply DM_FLAG_PRE_RELOC to the driver, allow it to bind before
relocation.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
In rzg2l_pinconf_set and rzg2l_get_pin_muxing if the call to
rzg2l_selector_decode fails then the variable pin may not have been
assigned to. Remove the use of pin from the error message. Also update
the error message to show the invalid selector used instead of port
which will be the error code returned.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Paul Barker <paul@pbarker.dev>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
In zynqmp_pinconf_set if param is PIN_CFG_IOSTANDARD or
PIN_CONFIG_POWER_SOURCE and zynqmp_pm_pinctrl_get_config returns an
error then value will not be assigned to when its value is tested to be
not equal to arg. Add code to only test value not equal to arg if ret is
false.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Link: https://lore.kernel.org/r/20250807-pinctrl_misc-v1-4-eeb564a1b032@linaro.org
Signed-off-by: Michal Simek <michal.simek@amd.com>
In zynqmp_pinctrl_prepare_func_groups if called with func->ngroups == 0
then ret will not be assigned to before its value is returned on exit.
Initialise ret to ensure it is always valid.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Link: https://lore.kernel.org/r/20250807-pinctrl_misc-v1-3-eeb564a1b032@linaro.org
Signed-off-by: Michal Simek <michal.simek@amd.com>
In s5pxx18_pinctrl_set_state testing count to be negative will always
fail as count is unsigned despite receiving the return value of a
function that returns an int. Change count and idx to be of type int to
allow the test to work as expected and remove the need for any implicit
casts. Also change pin to be u32 which is what all called functions
expect.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In stmfx_read_reg there is duplicated code to detect ret < 0 and return
ret if so. Remove one version of it.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In single_read there is a switch block with a default label. All cases
in the switch block, including the default, return directly. So any code
following the switch block is unreachable. Remove the unreachable code.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
A few pinctrl drivers cannot build without access to some platform
specific header files. Express those requirements in Kconfig as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
The driver specifies 154 pins so should have a maximum selector of 153
to ensure that the index into the array special_pins_names does not
overflow.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Link: https://lore.kernel.org/r/20250807-pinctrl_qcom-v1-2-42fac6707fd5@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
In sa8775p_get_pin_name the limit check for the index into
msm_special_pins_data allows for more elements than exist. Add code to
ensure the array index remains in bounds.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Link: https://lore.kernel.org/r/20250807-pinctrl_qcom-v1-1-42fac6707fd5@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
The name of the pin function was changed last minute in the DT, from
emac0 to gmac0.
Adjust the name we use in the pinctrl driver accordingly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The Linux pinctrl-sx150 was originally written as a GPIO driver
and fully rewritten by me as a Pinctrl driver and extended by
other contributors.
Fixup the Copyright header style and correctly report the
Copyright headers from the Linux driver.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The new DT pinctrl binding would allow us to read the pinmux values from
the DT, but it is actually easier to just continue with hardcoding the
mux values in the driver, and matching them against the "function" name.
Add the values for the primary and secondary pin controller on the A523.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The logic was updated without modifying the comment above it
Fixes: 72b8c6d1ebf ("pinctrl: don't fall back to pinctrl_select_state_simple()")
Signed-off-by: Philip Molloy <philip.molloy@analog.com>
The SoC pads of TH1520 are separated into three groups (AP 1, AP 2 and
AON) controlled by independent pin controllers. This patch ports their
driver from Linux kernel with most code for setting pinconf and pinmux
kept as is.
The dt-binding of TH1520 pin controller uses a schema where pins to
configure are specfied as strings and looked up at runtime, which the
generic pinctrl helpers of U-Boot cannot parse, thus a customized
set_state() callback is implemented to parse pinconfig nodes and setup
the configuration.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Acked-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The commit e8a9521e649f
("vf500/vf610: synchronise device trees with linux")
has synchronized U-Boot's DTS with v5.19 Linux kernel.
It turned out that in Linux's upstream iomuxc node description the
'fsl,mux_mask' was missing, so the U-Boot's pinctrl driver for NXP's
Vybrid SoC was not working properly.
As by default the mux mask was set to 0, for example the vf610 based
boards (like BK4) were bricked, due to misconfiguration of gpio at
early boot stage.
The fix for all NXP eligible boards is to define .mux_mask field for
soc specific *pinctrl_soc_info structure and use it directly in pinctrl
MMIO driver, without the need to read the "fsl,mux_mask" property from
device tree.
This change brings the NXP's pinctrl driver in U-Boot closer to Linux
upstream one.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com> #for i.MX8ULP
implement a driver to use semtech pinctrl and
gpio expander, this driver is adapted from a
existent linux driver that is written by
Gregory Bean <gbean@codeaurora.org>.
Signed-off-by: Anis Chali <chalianis1@gmail.com>
There's no need to modify private data from the controller, so let's
make that struct const.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There's no need to modify private data from the controller, so let's
make that struct const.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There's no need to modify private data from the controller, so let's
make that struct const.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There's no need to modify private data from the controller, so let's
make that struct const.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There's no need to modify private data from the controller, so let's
make that struct const.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There's no need to modify private data from the controller, so let's
make that struct const.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There's no need to modify private data from the controller, so let's
make that struct const.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There's no need to modify private data from the controller, so let's
make that struct const.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There's no need to modify private data from the controller, so let's
make that struct const.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There's no need to modify private data from the controller, so let's
make that struct const.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There's no need to modify private data from the controller, so let's
make that struct const.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There's no need to modify private data from the controller, so let's
make that struct const.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The logic in the core reads the nr_pins of the controller and uses it as
the index of the first pin in the bank (pin_base) it currently parses.
It then increments the number of pins in the controller before going to
the next bank.
This works "fine" for controllers where nr_pins isn't defined in their
rockchip_pin_ctrl struct as it defaults to 0. However, when it is
already set, it'll make the index pin of each bank offset by the number
in nr_pins declared in the struct at initialization, and it'll keep
growing while adding banks, which means the total number of pins in the
controller will be misrepresented.
Additionally, U-Boot proper may probe this driver twice (pre-reloc and
true proper) and not reset nr_pins of the controller in-between meaning
the second probe will have an offset of the actual correct nr_pins.
Instead, let's just store locally the number of pins in the controller
and make sure it's reset between probes.
Finally, this stops modifying a const struct which will soon be
triggering a CPU abort at runtime.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch adds SCMI pin control protocol support to make the pin
controller driver based on SCMI, such as
drivers/pinctrl/nxp/pinctrl-imx-scmi.c, can be bound to the SCMI agent
device whose protocol id is 0x19.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
This patch provides a pinctrl driver based on SCMI pin control protocol.
Currently, only the PINCTRL_CONFIG_SET command is implemented.
Signed-off-by: Ranjani Vaidyanathan <Ranjani.Vaidyanathan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Caleb Connolly <caleb.connolly@linaro.org> says:
Introduce a new event to signal that the live tree has been built,
allowing boards to perform fixups on the tree before devices are bound.
Crucially this allows for devices to be enabled or disabled, but also
allows for properties that are parsed during the bind stage to be
modified (such as dr_mode for dwc3).
With this in place, mach-snapdragon is switched over to use the event
and some hacky U-Boot specific DT overrides (which had to be undone
prior to booting an image) are removed in favour of fixing up the
livetree (which is not passed on to further boot stages).
Finally, some minor fixes are made for the QCM2290 RB1 board, the sdcard
is enabled and it now uses USB host mode in U-Boot like it's bigger
sibling the RB2.
Link: https://lore.kernel.org/r/20250411-livetree-fixup-v2-0-1236823377bb@linaro.org
There are 134 pins not 133, oops! This fixes the sdcard on the RB1 as
the pins now all get configured correctly.
Fixes: 0ecb8cfcb930 ("pinctrl: qcom: add qcm2290 pinctrl driver")
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Add support for the rk3576 variant of pinctrl.
Signed-off-by: Steven Liu <steven.liu@rock-chips.com>
[adapted to mainline u-boot]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add pinctrl driver for RK3528.
Imported from vendor U-Boot linux-6.1-stan-rkr5 tag with adjustments
to use regmap_update_bits().
Signed-off-by: Steven Liu <steven.liu@rock-chips.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
UART-A can be exposed through uSD, this was tested on Transformer T20
but should work on all Ventana-based boards.
TX is exported on SDD pingroup corresponding to uSD CLK pin
RX is exported on SDB which is CMD pin in uSD slot
Signed-off-by: Artur Kowalski <arturkow2000@gmail.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Applies same logic to general Tegra pincontrol driver as is done to Tegra20
by commit:
a35bf832d70 ("pinctrl: tegra20: detect unknown/invalid pin/func
configurations")
Suggested-by: Artur Kowalski <arturkow2000@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Tegra20 driver doesn't know about some pin configurations and even about
some pins. In case when pin configuration is unknown the pin would be
muxed to whatever is under function 0, in case when pin itself is
unknown, it could cause out-of-bounds array access in pinmux_set_func
and pinmux_set_pullupdown.
Signed-off-by: Artur Kowalski <arturkow2000@gmail.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Tom Rini <trini@konsulko.com> says:
This series switches to always using $(PHASE_) in Makefiles when
building rather than $(PHASE_) or $(XPL_). It also starts on documenting
this part of the build, but as a follow-up we need to rename
doc/develop/spl.rst and expand on explaining things a bit.
Link: https://lore.kernel.org/r/20250401225851.1125678-1-trini@konsulko.com
It is confusing to have both "$(PHASE_)" and "$(XPL_)" be used in our
Makefiles as part of the macros to determine when to do something in our
Makefiles based on what phase of the build we are in. For consistency,
bring this down to a single macro and use "$(PHASE_)" only.
Signed-off-by: Tom Rini <trini@konsulko.com>
Some Qualcomm boards feature reserved ranges of pins which are protected
by firmware. Attempting to read or write any registers associated with
these pins results the board resetting.
Add support for parsing these ranges from devicetree and ensure that the
pinctrl and GPIO drivers don't try to interact with these pins.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250410-topic-sm8x50-pinctrl-reserved-ranges-v2-1-654488392b9a@linaro.org
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
