When FEC network card works as the prime one in u-boot, and is in
active status, kernel might crash during booting up stage, especially
working with grub. Because the DMA of FEC is still in active status, and
copy data into memory if there is network data received. In this case, if
kernel allocated a part of memory that has overlay with the memory
used by DMA, kernel memory may be destroyed and cause kernel crashes.
Because before kernel boots up really, u-boot dm_remove_devices_flags()
can call the remove callback of FEC driver with DM_FLAG_ACTIVE_DMA
flag. In fecmxc_remove(), phy power is disabled, so there is no data
received. In this way, it makes sure that there is no DMA action, so
that avoid kernel crashing occurs.
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Currently if a gigabit-capable PHY is connected to FEC via RMII or MII, it
will advertise 1000FULL and 1000HALF to a link partner.
Different problems may arise here:
- usually with (R)MII between MAC and PHY the PHY's connection to magnetics
would have only 2 pairs routed as well, otherwise a PHY can negotiate 1000
speed and there will be no traffic possible;
- but even if there is no way to negotiate 1000 speed in HW (only 2 signal
pairs routed), it may take a lot of time for PHY to figure this out; in
case of AD1300 it takes 17-20 seconds, which is waay longer than default
4s PHY_ANEG_TIMEOUT.
Use phy_set_supported() in such cases to disable gigabit advertised
options.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
probing on capricorn board (imx8qxp based) brings:
Can't find FEC0 clk rate: -19
Cause is that when probing fec_mxc driver, fec_mii_setspeed()
is called which calls fec_get_clk_rate().
fec_mii_setspeed() calls fec_get_clk_rate with NULL pointer
for udev and so as in IMX8QXP case CLK_CCF is enabled
udev gets searched with:
uclass_get_device_by_seq(UCLASS_ETH, idx, &dev);
but we do not have yet a UCLASS_ETH ! as we just probing it!
Prevent this by passing udev to fec_get_clk_rate()
Signed-off-by: Heiko Schocher <hs@denx.de>
After FEC is halted by calling fec_halt callback, we should not continue
receiving packet. Otherwise it will process previous pending interrupts
on EIR register and uses wrong rbd index as this has been reset to 0.
The GRA interrupt which is triggered by issuing graceful stop command to
FEC transmitter in fec_halt is processed in this case. It causes wrong
receive buffer descriptors be used by FEC in next time.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX93 FEC ENET port supports two mode: RGMII and RMII. For RGMII,
there is an internal /2 divider, so the freq needs to set with (*2),
otherwise the speed will not reach 1G and cause communication error
in some network environments. For RMII, the clk path is
ccm -> enet tx_clk pin -> pad loop back to enet, no /2 divider.
So fix for RGMII mode with freq multiplied by 2.
Fixes: 09de565f76 ("net: fec_mxc: support i.MX93")
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The fec_mxc_init() function currently always returns 0. This does not
allow the callers to detect when for instance the PHY initialization
failed due to the port being unconnected. Fix that by returning the
status of fec_open().
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d, reversing
changes made to 2ee6f3a5f7.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Change to regulator_set_enable_if_allowed to avoid enable failure,
in case same phy supply shared by multiple FEC controllers.
Signed-off-by: Ye Li <ye.li@nxp.com>
Implement common board_interface_eth_init() and call it from the FEC
driver to configure IOMUXC GPR[1] register according to the PHY mode
obtained from DT. This supports all three interface modes supported by
the i.MX8M Mini/Nano/Plus FEC and supersedes the current board-side
configuration of the same IOMUX GPR[1] duplicated in the board files.
Signed-off-by: Marek Vasut <marex@denx.de>
The FEC ref clock frequency on i.MX8M Mini/Nano/Plus was so far configured
via ad-hoc board code. Replace that with DM clock clk_set_rate() instead.
This way, the driver claims all its required clock and sets the ref clock
rate, without any need of architecture specific register fiddling.
Signed-off-by: Marek Vasut <marex@denx.de>
This converts 6 usages of this option to the non-SPL form, since there is
no SPL_IMX_MODULE_FUSE defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for DM_MDIO by registering a UCLASS_MDIO driver and
attempting to use it. This is necessary if wanting to use a DSA
driver for example hanging off of the FEC MAC.
Care is taken to fallback to non DM_MDIO mii bus as several boards define
DM_MDIO without having the proper device-tree configuration necessary
such as an mdio subnode, a phy-mode prop, and either a valid phy-handle
prop or fixed-phy subnode which will cause dm_eth_phy_connect() to fail.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
At this point, the remaining places where we have a symbol that is
defined as CONFIG_... are in fairly odd locations. While as much dead
code has been removed as possible, some of these locations are simply
less obvious at first. In other cases, this code is used, but was
defined in such a way as to have been missed by earlier checks. Perform
a rename of all such remaining symbols to be CFG_... rather than
CONFIG_...
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This option is only used on one platform currently. However, with PHYLIB
enabled, which this platform also does, this option is not checked and
the functional use case is handled. Remove this code.
Signed-off-by: Tom Rini <trini@konsulko.com>
When gpio_request_by_name allocates a gpio output it by default will
de-assert the gpio which for phy-reset will take the PHY out of reset.
As this occurs before fec_gpio_reset is called to assert the reset
line it can cause undesired affects if reset timings are not properly
met.
Configure the gpio with GPIOD_IS_OUT_ACTIVE so that reset is kept active
(reset asserted) to avoid this.
Cc: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm-beacon
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Rename constant PHY_INTERFACE_MODE_NONE to PHY_INTERFACE_MODE_NA to make
it compatible with Linux' naming.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Add helpers ofnode_read_phy_mode() and dev_read_phy_mode() to parse the
"phy-mode" / "phy-connection-type" property. Add corresponding UT test.
Use them treewide.
This allows us to inline the phy_get_interface_by_name() into
ofnode_read_phy_mode(), since the former is not used anymore.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
With all boards now using DM_ETH we determine the value for
CONFIG_FEC_XCV_TYPE at run time, except in the case of the default
fall-back. Set the fallback directly now.
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that all boards have been converted, remove the non-DM_ETH code.
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last ARCH_MX25 platform, remove those
references as well.
Cc: Matthias Weisser <weisserm@arcor.de>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Enabling promiscuous mode is necessary if FEC is the master of a DSA
switch driver where each port has their own MAC address.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
If the FEC is connected to a fixed-link (upstream switch port for
example) the phy_of_node should be set to the fixed-link node
so that speed and other properties can be found properly.
In addition fix a typo in the debug string.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
When using uclass_get_device* to get the FEC device we need to use
device sequence instead of index into UCLASS_ETH. In systems where for
example a I2C based DSA switch exists it will probe before the FEC
master and its ports will be registered first and have the first
indexes yet the FEC's sequence comes from the device-tree alias.
Take for example the imx8mm-venice-gw7901 board which has an i2c based
DSA switch:
u-boot=> net list
eth1 : lan1 00:0d:8d:aa:00:2f
eth2 : lan2 00:0d:8d:aa:00:30
eth3 : lan3 00:0d:8d:aa:00:31
eth4 : lan4 00:0d:8d:aa:00:32
eth0 : ethernet@30be0000 00:0d:8d:aa:00:2e active
Thus in this case uclass_get_device(UCLASS_ETH, 0, &dev) returns lan1
which is wrong but uclass_get_device_seq(UCLASS_ETH, 0, &dev) returns
ethernet@30be000 which is correct.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
If we fail to probe for whatever reason, we cannot unregister/free the
MII bus unless we registered it with fec_get_miibus. This fixes FECs
sharing an MDIO bus from destroying it, preventing the other FEC from
using it.
Fixes: 6a895d039b ("net: Update eQos driver and FEC driver to use eth phy interfaces")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
If a phy is disabled, don't use it. This matches Linux's behavior.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
At present various drivers etc. access the device's 'seq' member directly.
This makes it harder to change the meaning of that member. Change access
to go through a function instead.
The drivers/i2c/lpc32xx_i2c.c file is left unchanged for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Some code was not converted by coccinelle, somehow.
I manually fixed up the remaining, and comments, README docs.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
[trini: Add arch/arm/mach-davinci/include/mach/sdmmc_defs.h and
include/fdt_support.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
As we move towards driver model, it is required to let the FEC driver
know how to properly deal with an Ethernet PHY subnode in the device tree.
For example:
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_microsom_enet_ar8035>;
phy-handle = <&phy>;
phy-mode = "rgmii-id";
phy-reset-duration = <2>;
phy-reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
status = "okay";
mdio {
#address-cells = <1>;
#size-cells = <0>;
phy: ethernet-phy@0 {
reg = <0>;
qca,clk-out-frequency = <125000000>;
};
};
};
Currently the PHY node pointer is incorrectly associated with the
Ethernel controller instead of the PHY node itself.
This causes the PHY properties, such as "qca,clk-out-frequency" in
the example above to not get parsed.
Fix this problem by populating the phy_of_node node.
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Tom Rini <trini@konsulko.com>
