PCA9450 PMIC supports reading the reset status from the PWRON_STAT
register. Bits 7-4 give indication of the PMIC reset cause:
- PWRON (BIT7) - Power ON triggered by PMIC_ON_REQ input line,
- WDOGB (BIT6) - Boot after cold reset by WDOGB pin (watchdog reset),
- SW_RST (BIT5) - Boot after cold reset initiated by the software,
- PMIC_RST (BIT4) - Boot after PMIC_RST_B input line trigger.
Add support for reading reset status via the sysreset framework in a
convenient printable format.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Paul Geurts <paul.geurts@prodrive-technologies.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The family of PCA9450 PMICs have the ability to perform system resets.
Restarting via PMIC is preferred method of restarting the system as all
the peripherals are brought to a know state after a power-cycle. The
PCA9450 features a cold restart procedure which is initiated by an I2C
command 0x14 to the SW_RST register.
Support in Linux for restarting via PCA9450 PMIC has been added by
Linux commit 6157e62b07d9 ("regulator: pca9450: Add restart handler").
Now add support for it also in the U-Boot via sysreset framework.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Paul Geurts <paul.geurts@prodrive-technologies.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The code in tps65910_regulator.c treats the field supply in struct
tps65910_regulator_pdata as an int and even tests the value for being
negative so change it from a u32 to int so that the code all works as
expected.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The commends in include/power/pmic.h say that once SPL_DM_PMIC exists we
should update things. This has been true for some time, so let us update
this to have the legacy portions in their own header, which should not
be directly included. This cleans up the logic within the file too
slightly.
Signed-off-by: Tom Rini <trini@konsulko.com>
The RK806 PMIC has a bitfield for configuring the restart/reset behavior
(which I assume Rockchip calls "function") whenever the PMIC is reset
either programmatically (c.f. DEV_RST in the datasheet) or via PWRCTRL
or RESETB pins.
For RK806, the following values are possible for RST_FUN:
0b00 means "Restart PMU"
0b01 means "Reset all the power off reset registers, forcing
the state to switch to ACTIVE mode"
0b10 means "Reset all the power off reset registers, forcing
the state to switch to ACTIVE mode, and simultaneously
pull down the RESETB PIN for 5mS before releasing"
0b11 means the same as for 0b10 just above.
This adds the appropriate logic in the driver to parse the new
rockchip,reset-mode DT property to pass this information. It just
happens that the values in the binding match the values to write in the
bitfield so no mapping is necessary.
For backward compatibility reasons, if the property is missing we set it
to 0b10 (i.e. BIT(7)) like before this commit was merged instead of
leaving it untouched like in the kernel driver.
Note that this does nothing useful for U-Boot at the moment as the ways
to reset the device (e.g. via `reset` command) doesn't interact with the
RK8xx PMIC and simply does a CPU reset.
Considering the upstream Linux kernel left this register untouched until
(assumed) v6.17[1], this is useful for cases in which the U-Boot
bootloader has this patch (and running with a DT with
rockchip,reset-mode property set) and running an upstream kernel before
(assumed) v6.17, or alternatively later without the property in the
kernel DT.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git/commit/?id=87b48d86b77686013f5c2a8866ed299312b671db
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
MAX8907 PMIC has embedded poweroff function used by some device to initiane
device power off. Implement it as optional sysreset driver guarded by
kconfig option and system-power-controller device tree property.
Tested-by: Ion Agorria <ion@agorria.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Added a new regulator driver for the MAXIM MAX8907 PMIC, providing
essential regulator functionalities and incorporated the necessary binding
framework within the core PMIC driver.
Tested-by: Ion Agorria <ion@agorria.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The CPCAP is a Motorola/ST-Ericsson creation, a multifunctional IC whose
main purpose was power control. It was used in a wide variety of Motorola
products, both Tegra and OMAP based. The most notable devices using this
PMIC are the Motorola Droid 4, Atrix 4G, and Droid X2.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
As per TRM[0] Section 8.7.1 "TPS6594-Q1 Registers", LDOx_Vout
bit 6-1, define the NVM voltage settings.
Along side table 8-4 of above TRM, shows voltage to value mapping.
Driver wrongly using bits 5-1 to calculate voltage, and to convert
voltage to value driver was using buck's calculation.
So fix those calculation.
[0]: https://www.ti.com/lit/ds/symlink/tps6594-q1.pdf
Fixes: 5d7dbd22cf7d ("power: regulator: tps65941: use function callbacks for conversion ops")
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Replace magic numbers in buckval2votl() & buckvolt2val() with macros to
help with clarity and correlate what the numbers correspond to in the
TPS65219 datasheet.
Signed-off-by: Shree Ramamoorthy <s-ramamoorthy@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add PCA9452 PMIC/Regulator support.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The MP5416 PMIC's LDO set-value formula is incorrect. This patch fixes
it by using the correct formula.
Signed-off-by: Sidharth Prabukumar <sidharth.prabukumar@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Both regulators_enable_boot_on/off() are unused and superseded by
regulator uclass regulator_post_probe(). Remove both functions.
Signed-off-by: Marek Vasut <marex@denx.de>
1. Use runtime voltage selection for LD/OD/ND mode.
2. According to latest PE/TE report, the voltages of VDD_SOC for
LD and ND mode need add 50mv margin, so LD voltage is 0.75v->0.8v,
ND voltage is 0.8v->0.85v.
3. Use TOFF_DEB to differentiate new trimmed pmic and old pmic
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Re-use the TPS65941 PMIC driver for TPS65224 PMIC.
Add additional macros of TPS65224 to aid in the driver
re-use.
Signed-off-by: Bhargav Raviprakash <bhargav.r@ltts.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This adds support for RK806, only the SPI variant has been tested.
The communication "protocol" over SPI is the following:
- write three bytes:
- 1 byte: [0:3] length of the payload, [6] Enable CRC, [7] Write
- 1 byte: LSB register address
- 1 byte: MSB register address
- write/read length of payload
The CRC is always disabled for now.
The RK806 technically supports I2C as well, and this should be able to
support it without any change, but it wasn't tested.
The DT node name prefix for the buck converters has changed in the
Device Tree and is now dcdc-reg. The logic for buck converters is
however manageable within the current logic inside the rk8xx regulator
driver. The same cannot be said for the NLDO and PLDO.
Because pmic_bind_children() parses the DT nodes and extracts the LDO
index from the DT node name, NLDO and PLDO will have overlapping
indices. Therefore, we need a separate logic from the already-existing
ldo callbacks. Let's reuse as much as possible though.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Those two functions had their last user removed in commit f9c68a566c4d
("rockchip: phycore_rk3288: remove phycore_init() function") part of
v2023.01 release, so let's do some cleanup here.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
These headers follow the pattern:
| #if CONFIG_IS_ENABLED(FANCY_FEATURE)
| void foo(void);
| #else
| static inline void foo(void) { return -ENOSYS; }
| #endif
In the #else path ENOSYS is used, however linux/errno.h is not included.
If errno.h has not been included already the compiler errors out even
if the inline function is not referenced.
Make those headers self contained.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
MAXIM Semiconductor's PMIC, MAX77663 has 8 GPIO pins and 3 GPIO-like
pins. It also supports interrupts from these pins.
Add GPIO driver for these pins to control via GPIO APIs.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
PALMAS PMIC family has embedded poweroff function used by some
device to initiane device power off. Implement it as sysreset
driver.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
TPS65910/TPS65911 PMICs have embedded power control functions
used by some device to initiane device power off. Implement it as
sysreset driver.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
TPS80031/TPS80032 PMICs have embedded power control functions
used by some device to initiane device power off. Implement it as
sysreset driver.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
MAX77663 PMIC has embedded poweroff function used by some
device to initiane device power off. Implement it as sysreset
driver.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Add support to bind the regulators/child nodes with the pmic.
Also adds the pmic i2c based read/write functions to access pmic
registers.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support to bind the regulators/child nodes with the pmic.
Also adds the pmic i2c based read/write functions to access pmic
registers.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support to bind the regulators/child nodes with the pmic.
Also adds the pmic i2c based read/write functions to access pmic
registers.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
With the commit 4fcba5d556b4 ("regulator: implement basic reference
counter"), keeping regulator enablement in balance become more important.
Calling regulator_autoset multiple times on a fixed regulator increase
the enable count for each call, resulting in an unbalanced enable count.
Introduce a AUTOSET_DONE flag and use it to mark that autoset has run
for the regulator. Return -EALREADY on any subsequent call to autoset.
This fixes so that the enable count is only ever increased by one per
regulator for autoset.
Fixes: 4fcba5d556b4 ("regulator: implement basic reference counter")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This avoids an error in converting to CONFIG_IS_ENABLED(DM_PMIC).
Many boards SPL code needs these definitions to compile, even if
the functions are not linked.
Signed-off-by: Troy Kisky <troykiskyboundary@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
PCA9451A uses similar BUCKs and LDO regulators as PCA9450B/C but
has LDO2 and LDO3 removed. So reuse pca9450 PMIC and regulator driver
and add new type for PCA9451A.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The highest register on ACT8846 is 0xf5, so set the number of registers
to 0xf6, ensuring that the pmic read/write commands are able to access
all of the supported registers (and many that are not valid, since the
register space is quite sparse).
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The default configuration of the PMIC behavior makes the PMIC
power cycle most regulators on WDOG_B assertion. This power
cycling causes the memory contents of OCRAM to be lost.
Some systems neeeds some memory that survives reset and
reboot, therefore this patch is created.
The implementation is taken almost verbatim from Linux commit
2364a64d0673f ("regulator: pca9450: Make warm reset on WDOG_B assertion")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
For Rockchip boards with the all rk8xx series PMICs (excluding the
rk808), it is sometimes desirable to not boot whenever the device is
plugged in. An example would be for the Odroid Go Advance.
This provides a configurable option to check the PMIC says it was
powered because of a plug-in event. If the value is 1 and this option
is selected, the device shuts down shortly after printing a message
to console stating the reason why it's shutting down. Powering up the
board with the power button is not affected.
This patch parallels the work done in the following patch series:
https://lore.kernel.org/u-boot/20220121133732.2397273-1-andre.przywara@arm.com/
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
- In a number of cases, use CONFIG_ARCH_EXYNOS[45] rather than
CONFIG_EXYNOS[45]
- In other cases, test for CONFIG_ARCH_EXYNOS or CONFIG_ARCH_S5PC1XX
- Migrate specific SoC CONFIG values to Kconfig
- Use CONFIG_TARGET_x rather than CONFIG_x
- Migrate other CONFIG_EXYNOS_x symbols to Kconfig
- Reference CONFIG_EXYNOS_RELOCATE_CODE_BASE directly as EXYNOS_RELOCATE_CODE_BASE
- Rename CONFIG_S5P_PA_SYSRAM to CONFIG_SMP_PEN_ADDR to match the rest
of U-Boot usage.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Depending on backup register value, U-Boot SPL maintains the debug unit
powered-on for debugging purpose; only BUCK1 is required for powering
the debug unit, so revert the setting for all the other power lanes,
except BUCK3 that has to be always on.
To be functional this patch requires a modification in the debugger
,openocd for example, to update the STM32MP15 backup register when it is
required to debug SPL after reset. After deeper analysis this behavior
will be never supported in tools so the associated code, will be never
used and the associated code can be removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add PCA9450 regulator driver. This is complementary driver for the BUCKn
and LDOn regulators provided by the PCA9450 PMIC driver. Currently the
driver permits reading the settngs and configuring the BUCKn and LDOn
regulators.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The TPS65219 I2S PMIC features 3 Buck converters and 4 linear regulators,
2 GPOs, 1 GPIO, and 3 multi-function-pin.
This adds the PMIC driver, loading the regulator sub-nodes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add missing MEMA - MEMD register definitions for PFUZE100.
Based on work from Heiko Schocher <hs@denx.de>.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
This converts the following to Kconfig:
CONFIG_POWER_I2C
CONFIG_POWER_LEGACY
They are handled at the same time due to a dependency between them.
Update the Makefile rule to use legacy power only in U-Boot proper.
Unfortunately a separate rule is needed in SPL to be able to build
legacy power. Add SPL related symbols for both, to allow for SPL-only
usage.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: More SPL related cleanups, reword commit message]
Signed-off-by: Tom Rini <trini@konsulko.com>
This option is used in pre-driver model code and much of it has never
been converted to driver model.
We want to add a new option to enable power support, so we can use a
simple rule in the Makefile. Rename this one, which is really about
a particular implementation of power.
Also update the pmic.h header file so it either includes the legacy
API or the driver model one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
TI J7200 EVM has lp876441 pmic that is similar to tps65941. Add support
for same with existing driver with new compatible.
Signed-off-by: Gowtham Tammana <g-tammana@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20210714205300.17424-2-g-tammana@ti.com
