* Remove deprecated Odroid XU4 legacy 4.14.y branch
* Clean deprecated kernels from meson64 family
- legacy kernel 4.9 was removed
- current 5.10 was replaced with 5.19
- edge remains on 5.19 until someone bumps it to 6
- patches between 5.11 and 5.18 were removed, 5.10 will be kept for awhile
* Update configs
* RockPI-S board has no video I/O
* udev rule to fix MAC address of iface based on UUID
Deals with WiFi chip lacking any EEPROM to store its unique Ethernet MAC address
Generic mechanism -- could be utilized for other boards having similar issues
* Handy Device Tree overlays for the RockPI S
Use armbian-add-overlay to install these
Reduce CPU voltage for the RK3308 B-S
Option to overclock RK3308 B-S to 1.3Ghz
Increase SDIO clock rate from 1Mhz to 10Mhz
This increases WiFi throughput from 300K bytes/s to 2.4M bytes/s
* corrected comment
* No longer repeat standard opp's in this dts
Require that the standard bs dts already be installed
* User README for adding RockPI-S board variant specific dts overlays
* "enabled" --> "okay"
* added mention of sdnand.dts, fixed typo
* added p2p0 to interfaces whose MAC address should be "fixed"
* RK3308 CPU serial number in nvmem replaces UUID for derivation of fixed MAC addr
Restored use of install utility
* Use RK3308 specific CPU serial number
rather than rootfs UUID
* remove generic fixMACaddress
* Install fixMACaddr file-by-file via install utility
* Drive SDIO bus signals faster
setting RK3308_SOC_CON0_VCCIO3 reduces signal rise/fall times to WiFi SDIO chip
from 30ns to 5ns.
This odd fix forward ported from legacy kernel.
Allows Rock Pi-S WiFi to operate at full speed.
* Set RK3308 I/O voltage domains before SDIO initializes
This patch moves responibility form the io-domain to the pinctrl driver because
the io-domain driver is probed after the SDIO devices are discovered.
This was causing multiple SDIO I/O failures during boot.
A new pinctrl property is added:
io-1v8-domains
is a u32 interpreted as a bit mask where each set bit corresponds to
a 1.8V I/O domain (as opposed to the default of 3.3V for I/O)
The mask is writted to the RK3308_SOC_CON0 GRF register
(once) when the pinctrl driver starts
The default mask is 0x10 where only I/O domain 4 runs at 1.8V
This is necessary for the RockPI-S to run the SDIO clock at high (50Mhz) speed
* align whitespace
* factored rk3308bs overlays out up sdio speedup patch
* factored dts for RK3308 iodomains and pinctrl patches out of speedup patch
* remains of sdio speedup patch merely add iodomains support for rk3308
* factored rockpis dts modification out from rk3308 io voltage domains
replaced rk3308 support from iodomains with
new io-voltage-domains property added to pinctrl
io-voltage-domains specific to rk3308 for now, others SOCs may be added later.
* add sequence numbering to names of rk3308 patches
* corrected tab alignment
* Add ssv6051p wifi driver for rockchip64 current and edge kernel
* also reorders and tidies device tree overlays for rk3318-box
* increase ssv6051 sdio bus to 50MHz in the driver
* Bump sunxi kernels
* sunxi-5.19: Remove pre-applied patch, adapt for series
* sunxi-5.15: Adapt patches to the series, remove previously applied
* Bump it again
Co-authored-by: The-going <48602507+The-going@users.noreply.github.com>
G12/GXL boards with memory of 1GB or lower are unable to boot because the CMA memory pool is set to high. Leaving CMA at the default and providing an overlay for those who need or want the CMA higher, makes more sense than not supporting all possible memory options provided by said SoC(s).
* meson: bump version
bump edge to thirdparty linux-5.18-rc7
bump current to linux-5.15
change legacy back to LTS linux-5.10
* Upgrade kernel config
* meson: edge and current: Enable NTFS3 driver
