* alias defined in patch 0007 is part of armada-372x.dtsi, so unnecessary in 37xx
* u-boot patch to dts shouldn't disable emmc or overwrite sdhci1
* update u-boot
* Rockchip64 Linux-5.10y - drivers for Motorcomm YT8531
renamed the previous "net-phy-Add-driver-for-Motorcomm-YT85xx-PHYs.patch" to "net-phy-Add-driver-for-Motorcomm-1-YT85xx-PHYs.patch" to fix patch order and added a new patch "net-phy-Add-driver-for-Motorcomm-2-YT8531-PHYs.patch"
The new YT8531 patch is sourced from from Lean's OpenWrt source rockchip/patches-5.10/601-net-phy-Add-driver-for-Motorcomm-YT8531-PHYs.patch.
It is intended to extend a patch identical to Armbian's "net-phy-Add-driver-for-Motorcomm-YT85xx-PHYs.patch" and is used without alteration.
* Add new board OrangePi R1 LTS (rk3328)
Includes uBoot and support for Linux-5.10y
* Rockchip64 Linux-5.15y drivers for YT8531 and other Motorcomm chips
YT8010, YT8510, YT8511, YT8512, YT8521. The driver patch set is sourced from Xunlong-OrangePi OpenWRT and is used as is, with only a name and makefile change.
A single patch set uses the same underlying source code as the Armbian Linux-5.10y set, but uses inbuilt logic to apply tweaks that depend on the Linux kernel version.
The patch is renamed similarly to the 5.10 patch set, net-phy-Add-driver-for-Motorcomm-T85xx+PHYs.patch to imply code base continuity with the previous similar Armbian patch sets.
* Rockchip64 Linux-5.15y support for Orange Pi R1 Plus LTS
Includes DTS and makefile changes. A driver for net phy YT8531C is in a separate commit
* change orangepi-r1plus-lts.csc to orangepi-r1plus-lts.conf
board is now supported
* - add patch also to 5.16.y
- fix wrong patch permission
* Fix Makefile patch
Co-authored-by: Igor Pecovnik <igor.pecovnik@gmail.com>
Radxa Zero 2 is a small form factor SBC based on the Amlogic A311D
chipset that ships in a number of eMMC configurations:
- Amlogic A311D (Quad A73 + Dual A53) CPU
- 4GB LPDDR4 RAM
- 32/64/128GB eMMC
- Mali G52-MP4 GPU
- HDMI 2.1 output (micro)
- BCM4345 WiFi (2.4/5GHz a/b/g/n/ac) and BT 5.0
- 1x USB 2.0 port - Type C (OTG)
- 1x USB 3.0 port - Type C (Host)
- 1x micro SD Card slot
- 40 Pin GPIO header
Signed-off-by: Yuntian Zhang <yt@radxa.com>
* Bump Meson64 u-boot to 2022.01
Tested VIM boards
* Move Jethub related patches under common meson64 patch collection
* Move jethub patch to per board and remove unneded settings
* Sync kernel config with radxa and remove packaging patch
* Merge the rockchip64 legacy config as well
* Lower priority of EFI partitioning against DOS partitioning which is used by Armbian
Co-authored-by: Catalin Toda <catalinii@yahoo.com>
* JetHome: Update u-boot patches: fix emmc work on JetHub D1
* JetHome: update kernel patches with last updates for JetHub devices.
* JetHome: Update Bluetooth init script to more stable start.
* Switched rockchip64 u-boot to v2021.07
* Switched OrangePi R1 Plus to include mainline's R2S device tree
* Added unsingned signed comparison patch from Paolo to fix rk3328 reboots
* Bugfix - Bananapi PRO seems to work fine with latest u-boot
Done many reboots and it didn't break. The same has to be tested with other A20 boards
* Set Allwinner 32bit hw to most recent u-boot 2021.07
* Let's move all to 2021.07 and test ...
* meson64: bump u-boot to 2021.07, rework patches
- as always based on chewitt's tree, with differences:
- squashed versions of HC4+SATA, Radxa Zero, DT tree sync patches
- so that DTB/config/code changes related to the same feature/board are grouped
- removed documentation changes and Makefile reordering patches
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* meson64: ODROID HC4/N2: simplify/remove board vs family hacks; better SPI support
- thanks to mainline 2021.07 u-boot and it's HC4 config we can remove the conditionals
- boards now define the u-boot vars instead of conditionals in family
- on the HC4, build u-boot twice: one for SD (old C4 config) and one for HC4 (new SATA/SPI config)
- reason is that the HC4 version does not work very well unless it is actually booted from SPI
- meson64_common: don't override UBOOT_TARGET_MAP if board-defined
- but the default UBOOT_TARGET_MAP is still defined if the board didn't
- (sneakily) add lm-sensors fancontrol to the HC4's board packages
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* Add support for Radxa Zero
u-boot: new patch based on v2021.04
kernel: use patches sent to kernel list by chewitt
Tested with minimal build and cinnamon desktop:
- SD/eMMC, ok
- USB3, works in USB 2 mode
- HDMI, ok
- WiFi/BT, ok
Signed-off-by: Jack Ma <jack@radxa.com>
* Add build targets
* Cleanup and set min speed to 666000
* Change to WIP target
Support status undetermined
Co-authored-by: Jack Ma <jack@radxa.com>
* [ Rockchip64 ] Add Tinker Board 2
Using Mainline ATF/U-boot/Kernel
What works:
- USB (NOT TYPE C)
- PCIe
- LED's
- Ethernet
- HDMI
TODO:
- Type-C (fusb302 stuff)
- Type-C DP
- Regulators for big cores and GPU (sitting at default values now, no DVFS)
- Formware/driver for RTL8822CE
U-boot spits out some trash right after handing off control from SPL to U-Boot,
but doesn't impact boot. Needs looked at.
* [ rockchip64 ] remove unrelated changes to 369ab2decdc5a3c49973d8eeb783c95558dcc41a
* [ rockchip64 ] fix merge mess from symlinks step 1
* [ rockchip64 ] fix merge mess from symlinks step 2
* [ rockchip64 ] fix merge mess from symlinks step 3
* [ rockchip64 ] add asus driver for FAN53200 regulator
* Rename tinkerboard.conf to tinkerboard.wip
set as WIP for merge to trunk. Not ready for images just yet.
* revert rename to wip
wrong tinkerboard
* Rename tinkerboard-2.conf to tinkerboard-2.wip
prepare for merge to trunk. Not ready for images
* Tinker Board 2 GPU and Type-C
Support USB3 over type-C connector. display Port is still non-functional, framework in device tree however
Enable GPU
* Tinkerboard 2 DTS tweaks
Added this round:
Type-C DP now works
thermal sensors enabled (oops)
* Tinker Board 2 update config
-Adds wifi support for the RTL8822
* Updated kernel/u-boot for MCIMX7SABRE board
Supporing 'current' and 'legacy' branches for MCIMX7SABRE board
current branch:
u-boot: imx_v2020.04_5.4.70_2.3.0
kernel: imx_5.4.70_2.3.0
legacy branch:
u-boot: imx_v2018.03_4.14.98_2.0.0_ga
kernel: imx_4.14.98_2.0.0_ga
* Update kernel config with few additional options like zram, bonding, ... just a few to keep minimum consistency over kernels.
* Fixed u-boot script and kernel config for i.MX7D
Fixed bug in u-boot script preventing to use armbianEnv.txt
Configured SDMA as module to fix loading SDMA firmware
Co-authored-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* remove obsolete and broken patch for pine64so u-boot
This prevents the image from being built.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* sunxi: fix pine64so phy-mode and add yt8511 support
Pine A64-LTS board should have RGMII-TXID mode instead of RGMII-ID (the
Realtek PHY chip's RXID is sometimes broken).
In addition, new Pine A64-LTS v2 board will use YT8511 instead of
RTL8211E, which still works under RGMII-TXID mode.
Backport YT8511 driver and phy-mode change from linux-next.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Co-authored-by: Igor Pečovnik <igorpecovnik@users.noreply.github.com>
* Updated kernel/u-boot for MCIMX7SABRE board
Supporing 'current' and 'legacy' branches for MCIMX7SABRE board
current branch:
u-boot: imx_v2020.04_5.4.70_2.3.0
kernel: imx_5.4.70_2.3.0
legacy branch:
u-boot: imx_v2018.03_4.14.98_2.0.0_ga
kernel: imx_4.14.98_2.0.0_ga
* Update kernel config with few additional options like zram, bonding, ... just a few to keep minimum consistency over kernels.
Co-authored-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* Remove unnecessary patch
- this patch works when compiling and installing manually.
- the dtb with the changes is taken from the kernel and not from u-boot, therefore this patch does not work.
* Add enable-audio-codec-bpim2ultra-kernel.patch
- Add patch to enable audio codec in bpi-m2-ultra with h3 compatible
- Built and tested on Armbian Buster with Kernel 5.11.x (edge)
* Bump imx6 edge to 5.12.y
* Bump odroid xu4 edge to 5.12.y
* Bump Jetson nano edge to 5.12.y
* WIP: Bump sunxi to 5.12.y
- create a copy of patches and make a new link
- wireless patches needs adjutement to 5.12
- some patches are still failing
* Adjust wireless patches to build on 5.12.y
* Remove template wireless patch
* Move Espressobin edge to 5.12.y
* Bump mvebu to 5.12
- patch 92-mvebu-gpio-remove-hardcoded-timer-assignment.patch was disabled @heisath
- adjusted wireless driver for 8723ds
* Adjust sunxi / sunxi64 edge to compile
* Fix kernel config for Jetson nano edge
* bump meson64 to 5.12.y
* bump rockchip edge to 5.12.y
* Bump rockchip64 to 5.12.y
* Bump rk322x edge to 5.12.y
@paolosabatino
* Cleanup im6, re-add 5.10.y patches since one is missing in 5.12.y
* Update odroidxu4 edge links
* rk322x: moved rk322x-edge to kernel 5.12, fix overlay compilation, retouched included kernel modules
* Cleanup: remove deprecated config
Co-authored-by: Paolo Sabatino <paolo.sabatino@gmail.com>
* Remove unnecessary patch
- this patch works when compiling and installing manually.
- the dtb with the changes is taken from the kernel and not from u-boot, therefore this patch does not work.
* Add enable-sound-pinecube-kernel.patch
- Add patch to enable audio codec in pinecube with v3s compatible
- Built and tested on Armbian Buster with Kernel 5.11.x (edge)
There are already emmc nodes in rk3288-tinker-s.dts, adding these nodes
to rk3288-tinker.dtsi will cause emmc busy loop on original Tinkerboard.
Signed-off-by: Jack Chen <redchenjs@live.com>
* fix SPL not booting due to signed/unsigned integer comparison
* gpio7 now uses dm-pre-reloc to correctly compile TPL
* adjusted minor thing is defconfig, more room for stacks
* includes patch for efuse for next v2021.04
- Enabled nfc on rk322x-dev and disable on rk322x-current (need further development)
- Tidied up rk322x-current device tree
- enabled nfc rockchip driver enabled in rk322x-dev kernel config
- Enabled EHCI controller in u-boot (added patch for inno-phy, device tree and config bits), better device detection for dwc2 usb otg port
- Removed SPL_FIT_GENERATOR from u-boot configuration, fixed .its file to use binman
- fixed rk322x its file (now includes dtb), reverted u-boot to v2020.10 and changed dev_* into log_debug() calls
* Adjust the RK808 buck step to improve stability
* Adjust vdd_log and enable vdd_center init voltage
For some reason, regulator-init-microvolt property under PMIC does not applied. Set the voltage on board file.
* Explicitly set vdd_log voltage for NanoPi M4V2 - possibly fix stability issues
* Regulator tweaks for NanoPi M4V2
* Add vdd_log to kernel and switch vdd_center back to 900mV
* Switch vdd_center to 0.95
* Make rk80x bucks voltage steps shorter to make the NanoPi M4V2 stable
* Tweak u-boot config for NanoPi M4V2
* Made the rk808 voltage steps configurable and configured 50mV for NanoPi M4V2
* Switched rockchip64/rk3399 to u-boot v2020.10
* Some tweaks for SPI booting on ROCK Pi 4 in u-boot v2020.10
* Adjusted NanoPi M4V2 config for u-boot v2020.10
* Disabled PREBOOT for RockPro64 in u-boot v2020.10
It breaks boot during fdt loading
* Fix issues with booting from SPI flash for RockPro64
* Moved NanoPi R4S patches to board specific folder
* Upgrade Meson64 u-boot to 2020.10
Tested on C1,C2 and C4
* Remove accidentaly added patch
* Remove patches that are not needed anymore and restore / adjust the one that is still needed for Lepotato
* sunxi: kernel: current/dev: enable sun6i-csi and disable LL debug on UART0
The former is useful on some boards, e.g. PineCube.
The latter blocks boards that do not utilize UART0 from booting.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* sunxi: add new family sun8i-v3s
This family is intended for boards with V3/V3s/S3/S3L chips and low
DRAM capacity.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* sunxi: add PineCube board
This board features Sochip S3 SoC (Allwinner V3 die + co-packaged 128MiB
DRAM), and an OmniVision OV5640 camera is shipped with the board.
Add support for it. It could be used as an IP camera then.
Kernel support is only added to current/dev branch, with dev just using
mainline-merged DT and current using backported DT from 5.10-rc.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* sunxi: kernel: current/dev: add V3s OHCI/EHCI nodes
These are needed for USB host on V3s boards to work.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* Move changed rockpis changed patch to board specific and add original one to z28pro
* Delete the patch unneeded for ROCK Pi S
Co-authored-by: Piotr Szczepanik <piter75@gmail.com>
* Enable ums and maskrom u-boot recovery button
* Configure USB MUX before starting download mode
* Blink system status led to notify user the download mode
* Move HDD power staggering to board function
* Configurable u-boot recovery for rockchip64 (ums,rockusb,fastboot,maskrom)
* Switch RockPro64 to configurable u-boot recovery
* Added a hook for board to prepare download mode
* Some fixes to mmc device detection
* Use dedicated led functions and fixups
