mirror of
https://source.denx.de/u-boot/u-boot.git
synced 2025-11-03 18:01:41 +01:00
9ac0e7b37a
UniPhier 32-bit SoCs use CONFIG_SPL_OF_CONTROL. So, many nodes must be marked as dm-pre-reloc to prevent fdtgrep from stripping them off. Sprinkling U-Boot-specific properties all over the place is painful because DT files are synced with Linux from time to time. Split u-boot,dm-pre-reloc out to uniphier-v7-u-boot.dtsi, which is appended to UniPhier V7 DTS before the build. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
123 lines
3.0 KiB
Plaintext
123 lines
3.0 KiB
Plaintext
if ARCH_UNIPHIER
|
|
|
|
config SYS_CONFIG_NAME
|
|
default "uniphier"
|
|
|
|
config ARCH_UNIPHIER_32BIT
|
|
bool
|
|
select CPU_V7
|
|
select CPU_V7_HAS_NONSEC
|
|
select ARMV7_NONSEC
|
|
select ARCH_SUPPORT_PSCI
|
|
|
|
choice
|
|
prompt "UniPhier SoC select"
|
|
default ARCH_UNIPHIER_V7_MULTI
|
|
|
|
config ARCH_UNIPHIER_LD4_SLD8
|
|
bool "UniPhier LD4/sLD8 SoCs"
|
|
select ARCH_UNIPHIER_32BIT
|
|
|
|
config ARCH_UNIPHIER_V7_MULTI
|
|
bool "UniPhier Pro4/Pro5/PXs2/LD6b SoCs"
|
|
select ARCH_UNIPHIER_32BIT
|
|
|
|
config ARCH_UNIPHIER_V8_MULTI
|
|
bool "UniPhier V8 SoCs"
|
|
depends on !SPL
|
|
select ARM64
|
|
select CMD_UNZIP
|
|
|
|
endchoice
|
|
|
|
config ARCH_UNIPHIER_LD4
|
|
bool "Enable UniPhier LD4 SoC support"
|
|
depends on ARCH_UNIPHIER_LD4_SLD8
|
|
default y
|
|
|
|
config ARCH_UNIPHIER_SLD8
|
|
bool "Enable UniPhier sLD8 SoC support"
|
|
depends on ARCH_UNIPHIER_LD4_SLD8
|
|
default y
|
|
|
|
config ARCH_UNIPHIER_PRO4
|
|
bool "Enable UniPhier Pro4 SoC support"
|
|
depends on ARCH_UNIPHIER_V7_MULTI
|
|
default y
|
|
|
|
config ARCH_UNIPHIER_PRO5
|
|
bool "Enable UniPhier Pro5 SoC support"
|
|
depends on ARCH_UNIPHIER_V7_MULTI
|
|
default y
|
|
|
|
config ARCH_UNIPHIER_PXS2
|
|
bool "Enable UniPhier Pxs2 SoC support"
|
|
depends on ARCH_UNIPHIER_V7_MULTI
|
|
default y
|
|
|
|
config ARCH_UNIPHIER_LD6B
|
|
bool "Enable UniPhier LD6b SoC support"
|
|
depends on ARCH_UNIPHIER_V7_MULTI
|
|
default y
|
|
|
|
config ARCH_UNIPHIER_LD11
|
|
bool "Enable UniPhier LD11 SoC support"
|
|
depends on ARCH_UNIPHIER_V8_MULTI
|
|
default y
|
|
|
|
config ARCH_UNIPHIER_LD20
|
|
bool "Enable UniPhier LD20 SoC support"
|
|
depends on ARCH_UNIPHIER_V8_MULTI
|
|
select OF_BOARD_SETUP
|
|
default y
|
|
|
|
config ARCH_UNIPHIER_PXS3
|
|
bool "Enable UniPhier PXs3 SoC support"
|
|
depends on ARCH_UNIPHIER_V8_MULTI
|
|
default y
|
|
|
|
config CACHE_UNIPHIER
|
|
bool "Enable the UniPhier L2 cache controller"
|
|
depends on ARCH_UNIPHIER_32BIT
|
|
select SYS_CACHE_SHIFT_7
|
|
default y
|
|
help
|
|
This option allows to use the UniPhier System Cache as L2 cache.
|
|
|
|
config MICRO_SUPPORT_CARD
|
|
bool "Use Micro Support Card"
|
|
help
|
|
This option provides support for the expansion board, available
|
|
on some UniPhier reference boards.
|
|
|
|
Say Y to use the on-board UART, Ether, LED devices.
|
|
|
|
config CMD_PINMON
|
|
bool "Enable boot mode pins monitor command"
|
|
default y
|
|
help
|
|
The command "pinmon" shows the state of the boot mode pins.
|
|
The boot mode pins are latched when the system reset is deasserted
|
|
and determine which device the system should load a boot image from.
|
|
|
|
config CMD_DDRPHY_DUMP
|
|
bool "Enable dump command of DDR PHY parameters"
|
|
depends on ARCH_UNIPHIER_LD4 || ARCH_UNIPHIER_PRO4 || \
|
|
ARCH_UNIPHIER_SLD8 || ARCH_UNIPHIER_LD11
|
|
default y
|
|
help
|
|
The command "ddrphy" shows the resulting parameters of DDR PHY
|
|
training; it is useful for the evaluation of DDR PHY training.
|
|
|
|
config CMD_DDRMPHY_DUMP
|
|
bool "Enable dump command of DDR Multi PHY parameters"
|
|
depends on ARCH_UNIPHIER_PXS2 || ARCH_UNIPHIER_LD6B
|
|
default y
|
|
help
|
|
The command "ddrmphy" shows the resulting parameters of DDR Multi PHY
|
|
training; it is useful for the evaluation of DDR Multi PHY training.
|
|
|
|
config SYS_SOC
|
|
default "uniphier-v7" if ARCH_UNIPHIER_LD4_SLD8 || ARCH_UNIPHIER_V7_MULTI
|
|
endif
|