mirror of
https://source.denx.de/u-boot/u-boot.git
synced 2025-09-19 21:01:51 +02:00
d678a59d2d
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay Ethernet"' I failed to notice that b4 noticed it was based on next and so took that as the base commit and merged that part of next to master. This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35. Reported-by: Jonas Karlman <jonas@kwiboo.se> Signed-off-by: Tom Rini <trini@konsulko.com>
125 lines
3.0 KiB
C
125 lines
3.0 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (C) 2011 by Vladimir Zapolskiy <vz@mleia.com>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <dm.h>
|
|
#include <ns16550.h>
|
|
|
|
#include <asm/arch/clk.h>
|
|
#include <asm/arch/uart.h>
|
|
#include <asm/arch/mux.h>
|
|
#include <asm/io.h>
|
|
|
|
static struct clk_pm_regs *clk = (struct clk_pm_regs *)CLK_PM_BASE;
|
|
static struct uart_ctrl_regs *ctrl = (struct uart_ctrl_regs *)UART_CTRL_BASE;
|
|
static struct mux_regs *mux = (struct mux_regs *)MUX_BASE;
|
|
|
|
void lpc32xx_uart_init(unsigned int uart_id)
|
|
{
|
|
if (uart_id < 1 || uart_id > 7)
|
|
return;
|
|
|
|
/* Disable loopback mode, if it is set by S1L bootloader */
|
|
clrbits_le32(&ctrl->loop, UART_LOOPBACK(uart_id));
|
|
|
|
if (uart_id < 3 || uart_id > 6)
|
|
return;
|
|
|
|
/* Enable UART system clock */
|
|
setbits_le32(&clk->uartclk_ctrl, CLK_UART(uart_id));
|
|
|
|
/* Set UART into autoclock mode */
|
|
clrsetbits_le32(&ctrl->clkmode,
|
|
UART_CLKMODE_MASK(uart_id),
|
|
UART_CLKMODE_AUTO(uart_id));
|
|
|
|
/* Bypass pre-divider of UART clock */
|
|
writel(CLK_UART_X_DIV(1) | CLK_UART_Y_DIV(1),
|
|
&clk->u3clk + (uart_id - 3));
|
|
}
|
|
|
|
#if !CONFIG_IS_ENABLED(OF_CONTROL)
|
|
static const struct ns16550_plat lpc32xx_uart[] = {
|
|
{ .base = UART3_BASE, .reg_shift = 2,
|
|
.clock = CFG_SYS_NS16550_CLK, .fcr = UART_FCR_DEFVAL, },
|
|
{ .base = UART4_BASE, .reg_shift = 2,
|
|
.clock = CFG_SYS_NS16550_CLK, .fcr = UART_FCR_DEFVAL, },
|
|
{ .base = UART5_BASE, .reg_shift = 2,
|
|
.clock = CFG_SYS_NS16550_CLK, .fcr = UART_FCR_DEFVAL, },
|
|
{ .base = UART6_BASE, .reg_shift = 2,
|
|
.clock = CFG_SYS_NS16550_CLK, .fcr = UART_FCR_DEFVAL, },
|
|
};
|
|
|
|
U_BOOT_DRVINFOS(lpc32xx_uarts) = {
|
|
{ "ns16550_serial", &lpc32xx_uart[0], },
|
|
{ "ns16550_serial", &lpc32xx_uart[1], },
|
|
{ "ns16550_serial", &lpc32xx_uart[2], },
|
|
{ "ns16550_serial", &lpc32xx_uart[3], },
|
|
};
|
|
#endif
|
|
|
|
void lpc32xx_dma_init(void)
|
|
{
|
|
/* Enable DMA interface */
|
|
writel(CLK_DMA_ENABLE, &clk->dmaclk_ctrl);
|
|
}
|
|
|
|
void lpc32xx_mac_init(void)
|
|
{
|
|
/* Enable MAC interface */
|
|
writel(CLK_MAC_REG | CLK_MAC_SLAVE | CLK_MAC_MASTER
|
|
#if defined(CONFIG_RMII)
|
|
| CLK_MAC_RMII,
|
|
#else
|
|
| CLK_MAC_MII,
|
|
#endif
|
|
&clk->macclk_ctrl);
|
|
}
|
|
|
|
void lpc32xx_mlc_nand_init(void)
|
|
{
|
|
/* Enable NAND interface */
|
|
writel(CLK_NAND_MLC | CLK_NAND_MLC_INT, &clk->flashclk_ctrl);
|
|
}
|
|
|
|
void lpc32xx_slc_nand_init(void)
|
|
{
|
|
/* Enable SLC NAND interface */
|
|
writel(CLK_NAND_SLC | CLK_NAND_SLC_SELECT, &clk->flashclk_ctrl);
|
|
}
|
|
|
|
void lpc32xx_usb_init(void)
|
|
{
|
|
/* Do not route the UART 5 Tx/Rx pins to the USB D+ and USB D- pins. */
|
|
clrbits_le32(&ctrl->ctrl, UART_CTRL_UART5_USB_MODE);
|
|
}
|
|
|
|
void lpc32xx_i2c_init(unsigned int devnum)
|
|
{
|
|
/* Enable I2C interface */
|
|
uint32_t ctrl = readl(&clk->i2cclk_ctrl);
|
|
if (devnum == 1)
|
|
ctrl |= CLK_I2C1_ENABLE;
|
|
if (devnum == 2)
|
|
ctrl |= CLK_I2C2_ENABLE;
|
|
writel(ctrl, &clk->i2cclk_ctrl);
|
|
}
|
|
|
|
U_BOOT_DRVINFO(lpc32xx_gpios) = {
|
|
.name = "gpio_lpc32xx"
|
|
};
|
|
|
|
/* Mux for SCK0, MISO0, MOSI0. We do not use SSEL0. */
|
|
|
|
#define P_MUX_SET_SSP0 0x1600
|
|
|
|
void lpc32xx_ssp_init(void)
|
|
{
|
|
/* Enable SSP0 interface */
|
|
writel(CLK_SSP0_ENABLE_CLOCK, &clk->ssp_ctrl);
|
|
/* Mux SSP0 pins */
|
|
writel(P_MUX_SET_SSP0, &mux->p_mux_set);
|
|
}
|