mirror of
https://source.denx.de/u-boot/u-boot.git
synced 2025-08-08 00:06:59 +02:00
d678a59d2d
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay Ethernet"' I failed to notice that b4 noticed it was based on next and so took that as the base commit and merged that part of next to master. This reverts commitc8ffd1356d, reversing changes made to2ee6f3a5f7. Reported-by: Jonas Karlman <jonas@kwiboo.se> Signed-off-by: Tom Rini <trini@konsulko.com>
99 lines
2.5 KiB
C
99 lines
2.5 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright 2018 NXP
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <log.h>
|
|
#include <linux/kernel.h>
|
|
#include <asm/arch/ddr.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
|
|
int ddr_cfg_phy(struct dram_timing_info *dram_timing)
|
|
{
|
|
struct dram_cfg_param *dram_cfg;
|
|
struct dram_fsp_msg *fsp_msg;
|
|
unsigned int num;
|
|
int i = 0;
|
|
int j = 0;
|
|
int ret;
|
|
|
|
/* initialize PHY configuration */
|
|
dram_cfg = dram_timing->ddrphy_cfg;
|
|
num = dram_timing->ddrphy_cfg_num;
|
|
for (i = 0; i < num; i++) {
|
|
/* config phy reg */
|
|
dwc_ddrphy_apb_wr(dram_cfg->reg, dram_cfg->val);
|
|
dram_cfg++;
|
|
}
|
|
|
|
/* load the frequency setpoint message block config */
|
|
fsp_msg = dram_timing->fsp_msg;
|
|
for (i = 0; i < dram_timing->fsp_msg_num; i++) {
|
|
debug("DRAM PHY training for %dMTS\n", fsp_msg->drate);
|
|
/* set dram PHY input clocks to desired frequency */
|
|
ddrphy_init_set_dfi_clk(fsp_msg->drate);
|
|
|
|
/* load the dram training firmware image */
|
|
dwc_ddrphy_apb_wr(0xd0000, 0x0);
|
|
ddr_load_train_firmware(fsp_msg->fw_type);
|
|
|
|
/* load the frequency set point message block parameter */
|
|
dram_cfg = fsp_msg->fsp_cfg;
|
|
num = fsp_msg->fsp_cfg_num;
|
|
for (j = 0; j < num; j++) {
|
|
dwc_ddrphy_apb_wr(dram_cfg->reg, dram_cfg->val);
|
|
dram_cfg++;
|
|
}
|
|
|
|
/*
|
|
* -------------------- excute the firmware --------------------
|
|
* Running the firmware is a simply process to taking the
|
|
* PMU out of reset and stall, then the firwmare will be run
|
|
* 1. reset the PMU;
|
|
* 2. begin the excution;
|
|
* 3. wait for the training done;
|
|
* 4. read the message block result.
|
|
* -------------------------------------------------------------
|
|
*/
|
|
dwc_ddrphy_apb_wr(0xd0000, 0x1);
|
|
dwc_ddrphy_apb_wr(0xd0099, 0x9);
|
|
dwc_ddrphy_apb_wr(0xd0099, 0x1);
|
|
dwc_ddrphy_apb_wr(0xd0099, 0x0);
|
|
|
|
/* Wait for the training firmware to complete */
|
|
ret = wait_ddrphy_training_complete();
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* Halt the microcontroller. */
|
|
dwc_ddrphy_apb_wr(0xd0099, 0x1);
|
|
|
|
/* Read the Message Block results */
|
|
dwc_ddrphy_apb_wr(0xd0000, 0x0);
|
|
|
|
ddrphy_init_read_msg_block(fsp_msg->fw_type);
|
|
|
|
if(fsp_msg->fw_type != FW_2D_IMAGE)
|
|
get_trained_CDD(i);
|
|
|
|
dwc_ddrphy_apb_wr(0xd0000, 0x1);
|
|
|
|
|
|
fsp_msg++;
|
|
}
|
|
|
|
/* Load PHY Init Engine Image */
|
|
dram_cfg = dram_timing->ddrphy_pie;
|
|
num = dram_timing->ddrphy_pie_num;
|
|
for (i = 0; i < num; i++) {
|
|
dwc_ddrphy_apb_wr(dram_cfg->reg, dram_cfg->val);
|
|
dram_cfg++;
|
|
}
|
|
|
|
/* save the ddr PHY trained CSR in memory for low power use */
|
|
ddrphy_trained_csr_save(ddrphy_trained_csr, ddrphy_trained_csr_num);
|
|
|
|
return 0;
|
|
}
|