mirror of
https://source.denx.de/u-boot/u-boot.git
synced 2025-10-31 00:11:51 +01:00
6706b115a6
This patch adds a driver for VSC9953 L2 Switch. This Vitesse IP is integrated in Freescale T1040 and T1020 SoCs. The L2 switch has 10 Ethernet ports: 2 internal fixed-links (ports 8 and 9) at 2.5 Gbps and and 8 external ports at 1 Gbps. The external ports may be connected to PHYs over QSGMII and SGMII. Commands have also been added to enable/disable a port and to check a port's link speed, duplexity and status. The commands are: ethsw port <port_nr> enable|disable - enable/disable an l2 switch port ethsw port <port_nr> show - show an l2 switch port's configuration port_nr=0..9; use "all" for all ports For more detailse please see doc/README.t1040-l2switch Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <yorksun@freescale.com>
49 lines
1.6 KiB
Plaintext
49 lines
1.6 KiB
Plaintext
This file contains information for VSC9953, a Vitesse L2 Switch IP
|
|
which is integrated in the T1040/T1020 Freescale SoCs.
|
|
|
|
About Device:
|
|
=============
|
|
VSC9953 is an 8-port Gigabit Ethernet switch supports the following features:
|
|
- 8192 MAC addresses
|
|
- Static Address provisioning
|
|
- Dynamic learning of MAC addresses and aging
|
|
- 4096 VLANs
|
|
- Independent and shared VLAN learning (IVL, SVL)
|
|
- Policing with storm control and MC/BC protection
|
|
- IPv4 and IPv6 multicast
|
|
- Jumbo frames (9.6 KB)
|
|
- Access Control List
|
|
- VLAN editing, translation and remarking
|
|
- RMON counters per port
|
|
|
|
Switch interfaces:
|
|
- 8 Gigabit switch ports (ports 0 to 7) are external and are connected to external PHYs
|
|
- 2 switch ports (ports 8 and 9) of 2.5 G are connected (fixed links)
|
|
to FMan ports (FM1@DTSEC1 and FM1@DTSEC2)
|
|
|
|
Commands Overview:
|
|
=============
|
|
Commands supported
|
|
- enable/disable a port
|
|
- check a port's link speed, duplexity and status.
|
|
|
|
Commands syntax
|
|
ethsw port <port_nr> enable|disable - enable/disable an l2 switch port
|
|
ethsw port <port_nr> show - show an l2 switch port's configuration
|
|
|
|
port_nr=0..9; use "all" for all ports
|
|
|
|
=> ethsw port all show
|
|
Port Status Link Speed Duplex
|
|
0 enabled down 10 half
|
|
1 enabled down 10 half
|
|
2 enabled down 10 half
|
|
3 enabled up 1000 full
|
|
4 disabled down - half
|
|
5 disabled down - half
|
|
6 disabled down - half
|
|
7 disabled down - half
|
|
8 enabled up 2500 full
|
|
9 enabled up 2500 full
|
|
=>
|