mirror of
				https://source.denx.de/u-boot/u-boot.git
				synced 2025-10-25 22:41:21 +02:00 
			
		
		
		
	Make the link-local code conform more completely with the RFC. This will prevent ARP queries for the target (such as while it is rebooting) from causing the device to choose a different link-local address, thinking that its address is in use by another machine. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
		
			
				
	
	
		
			346 lines
		
	
	
		
			8.3 KiB
		
	
	
	
		
			C
		
	
	
	
	
	
			
		
		
	
	
			346 lines
		
	
	
		
			8.3 KiB
		
	
	
	
		
			C
		
	
	
	
	
	
| /*
 | |
|  * RFC3927 ZeroConf IPv4 Link-Local addressing
 | |
|  * (see <http://www.zeroconf.org/>)
 | |
|  *
 | |
|  * Copied from BusyBox - networking/zcip.c
 | |
|  *
 | |
|  * Copyright (C) 2003 by Arthur van Hoff (avh@strangeberry.com)
 | |
|  * Copyright (C) 2004 by David Brownell
 | |
|  * Copyright (C) 2010 by Joe Hershberger
 | |
|  *
 | |
|  * Licensed under the GPL v2 or later
 | |
|  */
 | |
| 
 | |
| #include <common.h>
 | |
| #include <net.h>
 | |
| #include "arp.h"
 | |
| #include "net_rand.h"
 | |
| 
 | |
| /* We don't need more than 32 bits of the counter */
 | |
| #define MONOTONIC_MS() ((unsigned)get_timer(0) * (1000 / CONFIG_SYS_HZ))
 | |
| 
 | |
| enum {
 | |
| /* 169.254.0.0 */
 | |
| 	LINKLOCAL_ADDR = 0xa9fe0000,
 | |
| 
 | |
| 	IN_CLASSB_NET = 0xffff0000,
 | |
| 	IN_CLASSB_HOST = 0x0000ffff,
 | |
| 
 | |
| /* protocol timeout parameters, specified in seconds */
 | |
| 	PROBE_WAIT = 1,
 | |
| 	PROBE_MIN = 1,
 | |
| 	PROBE_MAX = 2,
 | |
| 	PROBE_NUM = 3,
 | |
| 	MAX_CONFLICTS = 10,
 | |
| 	RATE_LIMIT_INTERVAL = 60,
 | |
| 	ANNOUNCE_WAIT = 2,
 | |
| 	ANNOUNCE_NUM = 2,
 | |
| 	ANNOUNCE_INTERVAL = 2,
 | |
| 	DEFEND_INTERVAL = 10
 | |
| };
 | |
| 
 | |
| /* States during the configuration process. */
 | |
| static enum ll_state_t {
 | |
| 	PROBE = 0,
 | |
| 	RATE_LIMIT_PROBE,
 | |
| 	ANNOUNCE,
 | |
| 	MONITOR,
 | |
| 	DEFEND,
 | |
| 	DISABLED
 | |
| } state = DISABLED;
 | |
| 
 | |
| static IPaddr_t ip;
 | |
| static int timeout_ms = -1;
 | |
| static unsigned deadline_ms;
 | |
| static unsigned conflicts;
 | |
| static unsigned nprobes;
 | |
| static unsigned nclaims;
 | |
| static int ready;
 | |
| static unsigned int seed;
 | |
| 
 | |
| static void link_local_timeout(void);
 | |
| 
 | |
| /**
 | |
|  * Pick a random link local IP address on 169.254/16, except that
 | |
|  * the first and last 256 addresses are reserved.
 | |
|  */
 | |
| static IPaddr_t pick(void)
 | |
| {
 | |
| 	unsigned tmp;
 | |
| 
 | |
| 	do {
 | |
| 		tmp = rand_r(&seed) & IN_CLASSB_HOST;
 | |
| 	} while (tmp > (IN_CLASSB_HOST - 0x0200));
 | |
| 	return (IPaddr_t) htonl((LINKLOCAL_ADDR + 0x0100) + tmp);
 | |
| }
 | |
| 
 | |
| /**
 | |
|  * Return milliseconds of random delay, up to "secs" seconds.
 | |
|  */
 | |
| static inline unsigned random_delay_ms(unsigned secs)
 | |
| {
 | |
| 	return rand_r(&seed) % (secs * 1000);
 | |
| }
 | |
| 
 | |
| static void configure_wait(void)
 | |
| {
 | |
| 	if (timeout_ms == -1)
 | |
| 		return;
 | |
| 
 | |
| 	/* poll, being ready to adjust current timeout */
 | |
| 	if (!timeout_ms)
 | |
| 		timeout_ms = random_delay_ms(PROBE_WAIT);
 | |
| 
 | |
| 	/* set deadline_ms to the point in time when we timeout */
 | |
| 	deadline_ms = MONOTONIC_MS() + timeout_ms;
 | |
| 
 | |
| 	debug_cond(DEBUG_DEV_PKT, "...wait %d %s nprobes=%u, nclaims=%u\n",
 | |
| 			timeout_ms, eth_get_name(), nprobes, nclaims);
 | |
| 
 | |
| 	NetSetTimeout(timeout_ms, link_local_timeout);
 | |
| }
 | |
| 
 | |
| void link_local_start(void)
 | |
| {
 | |
| 	ip = getenv_IPaddr("llipaddr");
 | |
| 	if (ip != 0 && (ntohl(ip) & IN_CLASSB_NET) != LINKLOCAL_ADDR) {
 | |
| 		puts("invalid link address");
 | |
| 		net_set_state(NETLOOP_FAIL);
 | |
| 		return;
 | |
| 	}
 | |
| 	NetOurSubnetMask = IN_CLASSB_NET;
 | |
| 
 | |
| 	seed = seed_mac();
 | |
| 	if (ip == 0)
 | |
| 		ip = pick();
 | |
| 
 | |
| 	state = PROBE;
 | |
| 	timeout_ms = 0;
 | |
| 	conflicts = 0;
 | |
| 	nprobes = 0;
 | |
| 	nclaims = 0;
 | |
| 	ready = 0;
 | |
| 
 | |
| 	configure_wait();
 | |
| }
 | |
| 
 | |
| static void link_local_timeout(void)
 | |
| {
 | |
| 	switch (state) {
 | |
| 	case PROBE:
 | |
| 		/* timeouts in the PROBE state mean no conflicting ARP packets
 | |
| 		   have been received, so we can progress through the states */
 | |
| 		if (nprobes < PROBE_NUM) {
 | |
| 			nprobes++;
 | |
| 			debug_cond(DEBUG_LL_STATE, "probe/%u %s@%pI4\n",
 | |
| 					nprobes, eth_get_name(), &ip);
 | |
| 			arp_raw_request(0, NetEtherNullAddr, ip);
 | |
| 			timeout_ms = PROBE_MIN * 1000;
 | |
| 			timeout_ms += random_delay_ms(PROBE_MAX - PROBE_MIN);
 | |
| 		} else {
 | |
| 			/* Switch to announce state */
 | |
| 			state = ANNOUNCE;
 | |
| 			nclaims = 0;
 | |
| 			debug_cond(DEBUG_LL_STATE, "announce/%u %s@%pI4\n",
 | |
| 					nclaims, eth_get_name(), &ip);
 | |
| 			arp_raw_request(ip, NetOurEther, ip);
 | |
| 			timeout_ms = ANNOUNCE_INTERVAL * 1000;
 | |
| 		}
 | |
| 		break;
 | |
| 	case RATE_LIMIT_PROBE:
 | |
| 		/* timeouts in the RATE_LIMIT_PROBE state mean no conflicting
 | |
| 		   ARP packets have been received, so we can move immediately
 | |
| 		   to the announce state */
 | |
| 		state = ANNOUNCE;
 | |
| 		nclaims = 0;
 | |
| 		debug_cond(DEBUG_LL_STATE, "announce/%u %s@%pI4\n",
 | |
| 				nclaims, eth_get_name(), &ip);
 | |
| 		arp_raw_request(ip, NetOurEther, ip);
 | |
| 		timeout_ms = ANNOUNCE_INTERVAL * 1000;
 | |
| 		break;
 | |
| 	case ANNOUNCE:
 | |
| 		/* timeouts in the ANNOUNCE state mean no conflicting ARP
 | |
| 		   packets have been received, so we can progress through
 | |
| 		   the states */
 | |
| 		if (nclaims < ANNOUNCE_NUM) {
 | |
| 			nclaims++;
 | |
| 			debug_cond(DEBUG_LL_STATE, "announce/%u %s@%pI4\n",
 | |
| 					nclaims, eth_get_name(), &ip);
 | |
| 			arp_raw_request(ip, NetOurEther, ip);
 | |
| 			timeout_ms = ANNOUNCE_INTERVAL * 1000;
 | |
| 		} else {
 | |
| 			/* Switch to monitor state */
 | |
| 			state = MONITOR;
 | |
| 			printf("Successfully assigned %pI4\n", &ip);
 | |
| 			NetCopyIP(&NetOurIP, &ip);
 | |
| 			ready = 1;
 | |
| 			conflicts = 0;
 | |
| 			timeout_ms = -1;
 | |
| 			/* Never timeout in the monitor state */
 | |
| 			NetSetTimeout(0, NULL);
 | |
| 
 | |
| 			/* NOTE: all other exit paths should deconfig ... */
 | |
| 			net_set_state(NETLOOP_SUCCESS);
 | |
| 			return;
 | |
| 		}
 | |
| 		break;
 | |
| 	case DEFEND:
 | |
| 		/* We won!  No ARP replies, so just go back to monitor */
 | |
| 		state = MONITOR;
 | |
| 		timeout_ms = -1;
 | |
| 		conflicts = 0;
 | |
| 		break;
 | |
| 	default:
 | |
| 		/* Invalid, should never happen.  Restart the whole protocol */
 | |
| 		state = PROBE;
 | |
| 		ip = pick();
 | |
| 		timeout_ms = 0;
 | |
| 		nprobes = 0;
 | |
| 		nclaims = 0;
 | |
| 		break;
 | |
| 	}
 | |
| 	configure_wait();
 | |
| }
 | |
| 
 | |
| void link_local_receive_arp(struct arp_hdr *arp, int len)
 | |
| {
 | |
| 	int source_ip_conflict;
 | |
| 	int target_ip_conflict;
 | |
| 	IPaddr_t null_ip = 0;
 | |
| 
 | |
| 	if (state == DISABLED)
 | |
| 		return;
 | |
| 
 | |
| 	/* We need to adjust the timeout in case we didn't receive a
 | |
| 	   conflicting packet. */
 | |
| 	if (timeout_ms > 0) {
 | |
| 		unsigned diff = deadline_ms - MONOTONIC_MS();
 | |
| 		if ((int)(diff) < 0) {
 | |
| 			/* Current time is greater than the expected timeout
 | |
| 			   time. This should never happen */
 | |
| 			debug_cond(DEBUG_LL_STATE,
 | |
| 				"missed an expected timeout\n");
 | |
| 			timeout_ms = 0;
 | |
| 		} else {
 | |
| 			debug_cond(DEBUG_INT_STATE, "adjusting timeout\n");
 | |
| 			timeout_ms = diff | 1; /* never 0 */
 | |
| 		}
 | |
| 	}
 | |
| #if 0
 | |
|  /* XXX Don't bother with ethernet link just yet */
 | |
| 	if ((fds[0].revents & POLLIN) == 0) {
 | |
| 		if (fds[0].revents & POLLERR) {
 | |
| 			/*
 | |
| 			 * FIXME: links routinely go down;
 | |
| 			 */
 | |
| 			bb_error_msg("iface %s is down", eth_get_name());
 | |
| 			if (ready) {
 | |
| 				run(argv, "deconfig", &ip);
 | |
| 			}
 | |
| 			return EXIT_FAILURE;
 | |
| 		}
 | |
| 		continue;
 | |
| 	}
 | |
| #endif
 | |
| 
 | |
| 	debug_cond(DEBUG_INT_STATE, "%s recv arp type=%d, op=%d,\n",
 | |
| 		eth_get_name(), ntohs(arp->ar_pro),
 | |
| 		ntohs(arp->ar_op));
 | |
| 	debug_cond(DEBUG_INT_STATE, "\tsource=%pM %pI4\n",
 | |
| 		&arp->ar_sha,
 | |
| 		&arp->ar_spa);
 | |
| 	debug_cond(DEBUG_INT_STATE, "\ttarget=%pM %pI4\n",
 | |
| 		&arp->ar_tha,
 | |
| 		&arp->ar_tpa);
 | |
| 
 | |
| 	if (arp->ar_op != htons(ARPOP_REQUEST)
 | |
| 	 && arp->ar_op != htons(ARPOP_REPLY)
 | |
| 	) {
 | |
| 		configure_wait();
 | |
| 		return;
 | |
| 	}
 | |
| 
 | |
| 	source_ip_conflict = 0;
 | |
| 	target_ip_conflict = 0;
 | |
| 
 | |
| 	if (memcmp(&arp->ar_spa, &ip, ARP_PLEN) == 0
 | |
| 	 && memcmp(&arp->ar_sha, NetOurEther, ARP_HLEN) != 0
 | |
| 	) {
 | |
| 		source_ip_conflict = 1;
 | |
| 	}
 | |
| 
 | |
| 	/*
 | |
| 	 * According to RFC 3927, section 2.2.1:
 | |
| 	 * Check if packet is an ARP probe by checking for a null source IP
 | |
| 	 * then check that target IP is equal to ours and source hw addr
 | |
| 	 * is not equal to ours. This condition should cause a conflict only
 | |
| 	 * during probe.
 | |
| 	 */
 | |
| 	if (arp->ar_op == htons(ARPOP_REQUEST) &&
 | |
| 	    memcmp(&arp->ar_spa, &null_ip, ARP_PLEN) == 0 &&
 | |
| 	    memcmp(&arp->ar_tpa, &ip, ARP_PLEN) == 0 &&
 | |
| 	    memcmp(&arp->ar_sha, NetOurEther, ARP_HLEN) != 0) {
 | |
| 		target_ip_conflict = 1;
 | |
| 	}
 | |
| 
 | |
| 	debug_cond(DEBUG_NET_PKT,
 | |
| 		"state = %d, source ip conflict = %d, target ip conflict = "
 | |
| 		"%d\n", state, source_ip_conflict, target_ip_conflict);
 | |
| 	switch (state) {
 | |
| 	case PROBE:
 | |
| 	case ANNOUNCE:
 | |
| 		/* When probing or announcing, check for source IP conflicts
 | |
| 		   and other hosts doing ARP probes (target IP conflicts). */
 | |
| 		if (source_ip_conflict || target_ip_conflict) {
 | |
| 			conflicts++;
 | |
| 			state = PROBE;
 | |
| 			if (conflicts >= MAX_CONFLICTS) {
 | |
| 				debug("%s ratelimit\n", eth_get_name());
 | |
| 				timeout_ms = RATE_LIMIT_INTERVAL * 1000;
 | |
| 				state = RATE_LIMIT_PROBE;
 | |
| 			}
 | |
| 
 | |
| 			/* restart the whole protocol */
 | |
| 			ip = pick();
 | |
| 			timeout_ms = 0;
 | |
| 			nprobes = 0;
 | |
| 			nclaims = 0;
 | |
| 		}
 | |
| 		break;
 | |
| 	case MONITOR:
 | |
| 		/* If a conflict, we try to defend with a single ARP probe */
 | |
| 		if (source_ip_conflict) {
 | |
| 			debug("monitor conflict -- defending\n");
 | |
| 			state = DEFEND;
 | |
| 			timeout_ms = DEFEND_INTERVAL * 1000;
 | |
| 			arp_raw_request(ip, NetOurEther, ip);
 | |
| 		}
 | |
| 		break;
 | |
| 	case DEFEND:
 | |
| 		/* Well, we tried.  Start over (on conflict) */
 | |
| 		if (source_ip_conflict) {
 | |
| 			state = PROBE;
 | |
| 			debug("defend conflict -- starting over\n");
 | |
| 			ready = 0;
 | |
| 			NetOurIP = 0;
 | |
| 
 | |
| 			/* restart the whole protocol */
 | |
| 			ip = pick();
 | |
| 			timeout_ms = 0;
 | |
| 			nprobes = 0;
 | |
| 			nclaims = 0;
 | |
| 		}
 | |
| 		break;
 | |
| 	default:
 | |
| 		/* Invalid, should never happen.  Restart the whole protocol */
 | |
| 		debug("invalid state -- starting over\n");
 | |
| 		state = PROBE;
 | |
| 		ip = pick();
 | |
| 		timeout_ms = 0;
 | |
| 		nprobes = 0;
 | |
| 		nclaims = 0;
 | |
| 		break;
 | |
| 	}
 | |
| 	configure_wait();
 | |
| }
 |