Tom Rini 21e25992c8 Add new STM32 MCU boards and Documentation
STM32 programmer improvements
 video: support several LTDC HW versions and fix data enable polarity
 board: fix stboard error message, consider USB cable connected when boot device is USB
 configs: stm32mp1: set console variable for extlinux.conf
 configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
 ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
 phy: stm32-usbphyc: Add DT phy tuning support
 arm: dts: stm32mp15: alignment with v5.18
 ram: Conditionally enable ASR
 mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
 configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
 ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
 pinctrl: stm32: rework GPIO holes management
 -----BEGIN PGP SIGNATURE-----
 
 iQJQBAABCgA6FiEEXyrViUccKBz9c35Jysd4L3sz/6YFAmJ6U4QcHHBhdHJpY2Uu
 Y2hvdGFyZEBmb3NzLnN0LmNvbQAKCRDKx3gvezP/pg4SEACFSVRcCa/7r2QXObqk
 mORtlp6OrZLfCQGMugv9Oj0W+L4nanJEZEJknhasoHgm5CyTuCGEm7qxgWWBKA9j
 yeCfcpToXrY4cIMgsPR4tpZ9jn4fLsHFBEvCVMEoOp/K2ZI27lfJ0/OeRlgKdg11
 dTmM+J96vw7ltLHeN+yRWY1XgaGsBreqNJSO2mCGrAbbTJXSTrNZxP4wonTvKkFI
 GyTIgRaQA9ggk7/IhalusEEGIF0aaaX/z7uBXqEGkCyOTacLG5rxYNGCoaPdv1Bl
 fT7spZy1bAx3ABq/yJeF38Wi5jCXf55Z3cwYK0+tpJVUlAncYpJJBiyTERtR24OK
 NeDTWkw4e071xPDfmUFB96eINDQ8KXBRRcK2n2b6nW43loYtqgafrx4prL8W2T/u
 mB1WquNwjqdNN43iKAcyArrooOG18sJzRE3uAM6W4fjPx8DAHtYdaO3du3Mb5Kzz
 YaqgVO88NDsYaQRJCnmdQ7KDFToMy5A6btj2LhnYQ/3CMhktkg2RHC0aERGgNJLs
 ifVj3kvc+l8UwomvNOMjNket+AH7hbp64lbAfjAwzcgOGROKNyOslsr33qibg4lQ
 SQKl15wFDHLAcP2tj9QoUFO+97FqDXWBIzoEhDDBqfpVNRx25R7NePUkkA+0dHTS
 VedeNG6p2yFeW2UTAD4nYP9xWA==
 =s7xn
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-stm32-20220510' of https://source.denx.de/u-boot/custodians/u-boot-stm

Add new STM32 MCU boards and Documentation
STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
2022-05-10 15:28:02 -04:00
..
2021-11-11 19:01:56 -05:00
2022-02-25 01:41:04 -05:00
2022-05-02 09:58:13 -04:00
2021-10-01 21:08:18 -04:00
2022-05-03 21:39:22 +02:00
2021-08-14 20:54:41 +02:00
2022-04-25 16:04:05 -04:00
2022-05-07 23:17:25 +02:00
2018-01-22 16:43:30 -05:00
2020-07-09 20:58:05 +05:30
2020-09-30 16:55:03 -04:00
2020-07-16 12:37:01 +02:00
2022-04-25 16:04:05 -04:00

This patch series adds support for ZFS listing and load to u-boot.

To Enable zfs ls and load commands, modify the board specific config file with
#define CONFIG_CMD_ZFS

Steps to test:

1. After applying the patch, zfs specific commands can be seen
   in the boot loader prompt using
	UBOOT #help

	zfsload- load binary file from a ZFS file system
	zfsls  - list files in a directory (default /)

2. To list the files in zfs pool, device or partition, execute
	zfsls <interface> <dev[:part]> [POOL/@/dir/file]
	For example:
	UBOOT #zfsls mmc 0:5 /rpool/@/usr/bin/

3. To read and load a file from an ZFS formatted partition to RAM, execute
	zfsload <interface> <dev[:part]> [addr] [filename] [bytes]
	For example:
	UBOOT #zfsload mmc 2:2 0x30007fc0 /rpool/@/boot/uImage

References :
	-- ZFS GRUB sources from Solaris GRUB-0.97
	-- GRUB Bazaar repository

Jorgen Lundman <lundman at lundman.net> 2012.