mirror of
https://source.denx.de/u-boot/u-boot.git
synced 2025-08-31 11:31:27 +02:00
f4a5651044
Test whether this system is compatible with STM32MP15xx DHCOM SoM, if so, test whether R292 pull up is populated on pin PC3, which is an indication that the second MAC chip, KS8851-16MLL, is populated. Use this information to patch 'status' DT property into the second ethernet MAC DT node and enable/disable the MAC on systems where the chip is/isn't populated respectively. Use spl_perform_fixups() to patch the U-Boot proper DT from SPL and ft_board_setup() to patch Linux DT from U-Boot proper. This way both software components are configured the same way. Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
368 lines
5.8 KiB
Plaintext
368 lines
5.8 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
|
|
/*
|
|
* Copyright (C) 2019 Marek Vasut <marex@denx.de>
|
|
*/
|
|
|
|
#include <dt-bindings/clock/stm32mp1-clksrc.h>
|
|
#include "stm32mp15-u-boot.dtsi"
|
|
#include "stm32mp15-ddr3-dhsom-2x1Gb-1066-binG.dtsi"
|
|
#include "stm32mp15-ddr3-dhsom-2x2Gb-1066-binG.dtsi"
|
|
#include "stm32mp15-ddr3-dhsom-2x4Gb-1066-binG.dtsi"
|
|
|
|
/ {
|
|
aliases {
|
|
i2c1 = &i2c2;
|
|
i2c3 = &i2c4;
|
|
i2c4 = &i2c5;
|
|
mmc0 = &sdmmc1;
|
|
mmc1 = &sdmmc2;
|
|
spi0 = &qspi;
|
|
usb0 = &usbotg_hs;
|
|
eeprom0 = &eeprom0;
|
|
};
|
|
|
|
config {
|
|
u-boot,boot-led = "heartbeat";
|
|
u-boot,error-led = "error";
|
|
dh,som-coding-gpios = <&gpiof 12 0>, <&gpiof 13 0>, <&gpiof 15 0>;
|
|
dh,ddr3-coding-gpios = <&gpioz 6 0>, <&gpioz 7 0>;
|
|
dh,mac-coding-gpios = <&gpioc 3 0>;
|
|
};
|
|
};
|
|
|
|
ðernet0 {
|
|
phy-reset-gpios = <&gpioh 3 GPIO_ACTIVE_LOW>;
|
|
/delete-property/ st,eth-ref-clk-sel;
|
|
};
|
|
|
|
ðernet0_rmii_pins_a {
|
|
pins1 {
|
|
pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH1_RMII_TXD0 */
|
|
<STM32_PINMUX('G', 14, AF11)>, /* ETH1_RMII_TXD1 */
|
|
<STM32_PINMUX('B', 11, AF11)>, /* ETH1_RMII_TX_EN */
|
|
<STM32_PINMUX('A', 1, AF11)>, /* ETH1_RMII_REF_CLK */
|
|
<STM32_PINMUX('A', 2, AF11)>, /* ETH1_MDIO */
|
|
<STM32_PINMUX('C', 1, AF11)>; /* ETH1_MDC */
|
|
};
|
|
};
|
|
|
|
&i2c4 {
|
|
bootph-all;
|
|
bootph-pre-ram;
|
|
|
|
eeprom0: eeprom@50 {
|
|
};
|
|
};
|
|
|
|
&i2c4_pins_a {
|
|
bootph-all;
|
|
pins {
|
|
bootph-all;
|
|
};
|
|
};
|
|
|
|
&phy0 {
|
|
/delete-property/ reset-gpios;
|
|
};
|
|
|
|
&pinctrl {
|
|
mco2_pins_a: mco2-0 {
|
|
pins {
|
|
pinmux = <STM32_PINMUX('G', 2, AF1)>; /* MCO2 */
|
|
bias-disable;
|
|
drive-push-pull;
|
|
slew-rate = <2>;
|
|
};
|
|
};
|
|
|
|
mco2_sleep_pins_a: mco2-sleep-0 {
|
|
pins {
|
|
pinmux = <STM32_PINMUX('G', 2, ANALOG)>; /* MCO2 */
|
|
};
|
|
};
|
|
};
|
|
|
|
&pmic {
|
|
bootph-all;
|
|
bootph-pre-ram;
|
|
|
|
regulators {
|
|
bootph-pre-ram;
|
|
};
|
|
};
|
|
|
|
&flash0 {
|
|
bootph-pre-ram;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "fsbl1";
|
|
reg = <0x00000000 0x00040000>;
|
|
};
|
|
partition@40000 {
|
|
label = "fsbl2";
|
|
reg = <0x00040000 0x00040000>;
|
|
};
|
|
partition@80000 {
|
|
label = "uboot";
|
|
reg = <0x00080000 0x00160000>;
|
|
};
|
|
partition@1e0000 {
|
|
label = "env1";
|
|
reg = <0x001E0000 0x00010000>;
|
|
};
|
|
partition@1f0000 {
|
|
label = "env2";
|
|
reg = <0x001F0000 0x00010000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&qspi {
|
|
bootph-pre-ram;
|
|
};
|
|
|
|
&qspi_clk_pins_a {
|
|
bootph-pre-ram;
|
|
pins {
|
|
bootph-pre-ram;
|
|
};
|
|
};
|
|
|
|
&qspi_bk1_pins_a {
|
|
bootph-pre-ram;
|
|
pins {
|
|
bootph-pre-ram;
|
|
};
|
|
};
|
|
|
|
&qspi_cs1_pins_a {
|
|
bootph-pre-ram;
|
|
pins {
|
|
bootph-pre-ram;
|
|
};
|
|
};
|
|
|
|
&rcc {
|
|
/*
|
|
* Reinstate clock names from stm32mp151.dtsi, the MCO2 trick
|
|
* used in stm32mp15xx-dhcom-som.dtsi is not supported by the
|
|
* U-Boot clock framework.
|
|
*/
|
|
clock-names = "hse", "hsi", "csi", "lse", "lsi";
|
|
clocks = <&clk_hse>, <&clk_hsi>, <&clk_csi>,
|
|
<&clk_lse>, <&clk_lsi>;
|
|
|
|
/* The MCO2 is already configured correctly, remove those. */
|
|
/delete-property/ assigned-clocks;
|
|
/delete-property/ assigned-clock-parents;
|
|
/delete-property/ assigned-clock-rates;
|
|
|
|
st,clksrc = <
|
|
CLK_MPU_PLL1P
|
|
CLK_AXI_PLL2P
|
|
CLK_MCU_PLL3P
|
|
CLK_PLL12_HSE
|
|
CLK_PLL3_HSE
|
|
CLK_PLL4_HSE
|
|
CLK_RTC_LSE
|
|
CLK_MCO1_DISABLED
|
|
CLK_MCO2_PLL4P
|
|
>;
|
|
|
|
st,clkdiv = <
|
|
1 /*MPU*/
|
|
0 /*AXI*/
|
|
0 /*MCU*/
|
|
1 /*APB1*/
|
|
1 /*APB2*/
|
|
1 /*APB3*/
|
|
1 /*APB4*/
|
|
2 /*APB5*/
|
|
23 /*RTC*/
|
|
0 /*MCO1*/
|
|
1 /*MCO2*/
|
|
>;
|
|
|
|
st,pkcs = <
|
|
CLK_CKPER_HSE
|
|
CLK_FMC_ACLK
|
|
CLK_QSPI_ACLK
|
|
CLK_ETH_PLL4P
|
|
CLK_SDMMC12_PLL4P
|
|
CLK_DSI_DSIPLL
|
|
CLK_STGEN_HSE
|
|
CLK_USBPHY_HSE
|
|
CLK_SPI2S1_PLL3Q
|
|
CLK_SPI2S23_PLL3Q
|
|
CLK_SPI45_HSI
|
|
CLK_SPI6_HSI
|
|
CLK_I2C46_HSI
|
|
CLK_SDMMC3_PLL4P
|
|
CLK_USBO_USBPHY
|
|
CLK_ADC_CKPER
|
|
CLK_CEC_LSE
|
|
CLK_I2C12_HSI
|
|
CLK_I2C35_HSI
|
|
CLK_UART1_HSI
|
|
CLK_UART24_HSI
|
|
CLK_UART35_HSI
|
|
CLK_UART6_HSI
|
|
CLK_UART78_HSI
|
|
CLK_SPDIF_PLL4P
|
|
CLK_FDCAN_PLL4R
|
|
CLK_SAI1_PLL3Q
|
|
CLK_SAI2_PLL3Q
|
|
CLK_SAI3_PLL3Q
|
|
CLK_SAI4_PLL3Q
|
|
CLK_RNG1_LSI
|
|
CLK_RNG2_LSI
|
|
CLK_LPTIM1_PCLK1
|
|
CLK_LPTIM23_PCLK3
|
|
CLK_LPTIM45_LSE
|
|
>;
|
|
|
|
/*
|
|
* cfg = < DIVM1 DIVN P Q R PQR(p,q,r) >;
|
|
* frac = < f >;
|
|
*
|
|
* PRQ(p,q,r) ... for p,q,r: 0-output disabled / 1-output enabled
|
|
* DIVN ... actually multiplier, but RCC_PLL1CFGR1 calls the field DIVN
|
|
* m ... for PLL1,2: m=2 ; for PLL3,4: m=1
|
|
* XTAL = 24 MHz
|
|
*
|
|
* VCO = ( XTAL / (DIVM1 + 1) ) * m * ( DIVN + 1 + ( f / 8192 ) )
|
|
* P = VCO / (P + 1)
|
|
* Q = VCO / (Q + 1)
|
|
* R = VCO / (R + 1)
|
|
*/
|
|
|
|
/* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
|
|
pll2: st,pll@1 {
|
|
compatible = "st,stm32mp1-pll";
|
|
reg = <1>;
|
|
cfg = < 2 65 1 0 0 PQR(1,1,1) >;
|
|
frac = < 0x1400 >;
|
|
bootph-all;
|
|
};
|
|
|
|
/* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
|
|
pll3: st,pll@2 {
|
|
compatible = "st,stm32mp1-pll";
|
|
reg = <2>;
|
|
cfg = < 1 33 1 16 36 PQR(1,1,1) >;
|
|
frac = < 0x1a04 >;
|
|
bootph-all;
|
|
};
|
|
|
|
/* VCO = 600.0 MHz => P = 100, Q = 50, R = 50 */
|
|
pll4: st,pll@3 {
|
|
compatible = "st,stm32mp1-pll";
|
|
reg = <3>;
|
|
cfg = < 1 49 5 11 11 PQR(1,1,1) >;
|
|
bootph-all;
|
|
};
|
|
};
|
|
|
|
&sdmmc1 {
|
|
bootph-pre-ram;
|
|
st,use-ckin;
|
|
st,cmd-gpios = <&gpiod 2 0>;
|
|
st,ck-gpios = <&gpioc 12 0>;
|
|
st,ckin-gpios = <&gpioe 4 0>;
|
|
};
|
|
|
|
&sdmmc1_b4_pins_a {
|
|
bootph-pre-ram;
|
|
pins1 {
|
|
bootph-pre-ram;
|
|
};
|
|
pins2 {
|
|
bootph-pre-ram;
|
|
};
|
|
};
|
|
|
|
&sdmmc1_dir_pins_a {
|
|
bootph-pre-ram;
|
|
pins1 {
|
|
bootph-pre-ram;
|
|
};
|
|
pins2 {
|
|
bootph-pre-ram;
|
|
};
|
|
};
|
|
|
|
&sdmmc2 {
|
|
bootph-pre-ram;
|
|
};
|
|
|
|
&sdmmc2_b4_pins_a {
|
|
bootph-pre-ram;
|
|
pins {
|
|
bootph-pre-ram;
|
|
};
|
|
};
|
|
|
|
&sdmmc2_d47_pins_a {
|
|
bootph-pre-ram;
|
|
pins {
|
|
bootph-pre-ram;
|
|
};
|
|
};
|
|
|
|
&uart4 {
|
|
bootph-all;
|
|
};
|
|
|
|
&uart4_pins_a {
|
|
bootph-all;
|
|
pins1 {
|
|
bootph-all;
|
|
};
|
|
pins2 {
|
|
bootph-all;
|
|
/* pull-up on rx to avoid floating level */
|
|
bias-pull-up;
|
|
};
|
|
};
|
|
|
|
®11 {
|
|
bootph-pre-ram;
|
|
};
|
|
|
|
®18 {
|
|
bootph-pre-ram;
|
|
};
|
|
|
|
&usb33 {
|
|
bootph-pre-ram;
|
|
};
|
|
|
|
&usbotg_hs_pins_a {
|
|
bootph-pre-ram;
|
|
};
|
|
|
|
&usbotg_hs {
|
|
bootph-pre-ram;
|
|
};
|
|
|
|
&usbphyc {
|
|
bootph-pre-ram;
|
|
};
|
|
|
|
&usbphyc_port0 {
|
|
bootph-pre-ram;
|
|
};
|
|
|
|
&usbphyc_port1 {
|
|
bootph-pre-ram;
|
|
};
|
|
|
|
&vdd_usb {
|
|
bootph-pre-ram;
|
|
};
|