mirror of
https://source.denx.de/u-boot/u-boot.git
synced 2025-08-23 07:31:27 +02:00
1f47e2aca4
common: - Align ENV_FAT_INTERFACE - Fix MAC address source print log - Improve based autodetection code xilinx: - Enable netconsole Microblaze: - Setup default ENV_OFFSET/ENV_SECT_SIZE Zynq: - Multiple DT updates/fixes - Use DEVICE_TREE environment variable for DTB selection - Switch to single zynq configuration - Enable NOR flash via DM - Minor SPL print removal - Enable i2c mux driver ZynqMP: - Print multiboot register - Enable cache commands in mini mtest - Multiple DT updates/fixes - Fix firmware probing when driver is not enabled - Specify 3rd backup RAM boot mode in SPL - Add SPL support for zcu102 v1.1 and zcu111 revA - Redesign debug uart enabling and psu_init delay - Enable full u-boot run from EL3 - Enable u-boot.itb generation without ATF with U-Boot in EL3 Versal: - Enable distro default - Enable others SPI flashes - Enable systems without DDR Drivers: - Gem: - Flush memory after freeing - Handle mdio bus separately - Watchdog: - Get rid of unused global data pointer - Enable window watchdog timer - Serial: - Change reinitialization logic in zynq serial driver -----BEGIN PGP SIGNATURE----- iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXoxw9wAKCRDKSWXLKUoM IbQxAKCK23yTy4FoN8oTGTYsbmLOA9kVUQCbBx8lg4nBeA8ihSaAnY+HMDF37YI= =Lg54 -----END PGP SIGNATURE----- Merge tag 'xilinx-for-v2020.07' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next Xilinx changes for v2020.07 common: - Align ENV_FAT_INTERFACE - Fix MAC address source print log - Improve based autodetection code xilinx: - Enable netconsole Microblaze: - Setup default ENV_OFFSET/ENV_SECT_SIZE Zynq: - Multiple DT updates/fixes - Use DEVICE_TREE environment variable for DTB selection - Switch to single zynq configuration - Enable NOR flash via DM - Minor SPL print removal - Enable i2c mux driver ZynqMP: - Print multiboot register - Enable cache commands in mini mtest - Multiple DT updates/fixes - Fix firmware probing when driver is not enabled - Specify 3rd backup RAM boot mode in SPL - Add SPL support for zcu102 v1.1 and zcu111 revA - Redesign debug uart enabling and psu_init delay - Enable full u-boot run from EL3 - Enable u-boot.itb generation without ATF with U-Boot in EL3 Versal: - Enable distro default - Enable others SPI flashes - Enable systems without DDR Drivers: - Gem: - Flush memory after freeing - Handle mdio bus separately - Watchdog: - Get rid of unused global data pointer - Enable window watchdog timer - Serial: - Change reinitialization logic in zynq serial driver Signed-off-by: Tom Rini <trini@konsulko.com>
This patch series adds support for ZFS listing and load to u-boot. To Enable zfs ls and load commands, modify the board specific config file with #define CONFIG_CMD_ZFS Steps to test: 1. After applying the patch, zfs specific commands can be seen in the boot loader prompt using UBOOT #help zfsload- load binary file from a ZFS file system zfsls - list files in a directory (default /) 2. To list the files in zfs pool, device or partition, execute zfsls <interface> <dev[:part]> [POOL/@/dir/file] For example: UBOOT #zfsls mmc 0:5 /rpool/@/usr/bin/ 3. To read and load a file from an ZFS formatted partition to RAM, execute zfsload <interface> <dev[:part]> [addr] [filename] [bytes] For example: UBOOT #zfsload mmc 2:2 0x30007fc0 /rpool/@/boot/uImage References : -- ZFS GRUB sources from Solaris GRUB-0.97 -- GRUB Bazaar repository Jorgen Lundman <lundman at lundman.net> 2012.