mirror of
https://source.denx.de/u-boot/u-boot.git
synced 2025-09-19 04:41:30 +02:00
21e25992c8
STM32 programmer improvements video: support several LTDC HW versions and fix data enable polarity board: fix stboard error message, consider USB cable connected when boot device is USB configs: stm32mp1: set console variable for extlinux.conf configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link ARM: stm32mp: Fix Silicon version handling and ft_system_setup() phy: stm32-usbphyc: Add DT phy tuning support arm: dts: stm32mp15: alignment with v5.18 ram: Conditionally enable ASR mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM pinctrl: stm32: rework GPIO holes management -----BEGIN PGP SIGNATURE----- iQJQBAABCgA6FiEEXyrViUccKBz9c35Jysd4L3sz/6YFAmJ6U4QcHHBhdHJpY2Uu Y2hvdGFyZEBmb3NzLnN0LmNvbQAKCRDKx3gvezP/pg4SEACFSVRcCa/7r2QXObqk mORtlp6OrZLfCQGMugv9Oj0W+L4nanJEZEJknhasoHgm5CyTuCGEm7qxgWWBKA9j yeCfcpToXrY4cIMgsPR4tpZ9jn4fLsHFBEvCVMEoOp/K2ZI27lfJ0/OeRlgKdg11 dTmM+J96vw7ltLHeN+yRWY1XgaGsBreqNJSO2mCGrAbbTJXSTrNZxP4wonTvKkFI GyTIgRaQA9ggk7/IhalusEEGIF0aaaX/z7uBXqEGkCyOTacLG5rxYNGCoaPdv1Bl fT7spZy1bAx3ABq/yJeF38Wi5jCXf55Z3cwYK0+tpJVUlAncYpJJBiyTERtR24OK NeDTWkw4e071xPDfmUFB96eINDQ8KXBRRcK2n2b6nW43loYtqgafrx4prL8W2T/u mB1WquNwjqdNN43iKAcyArrooOG18sJzRE3uAM6W4fjPx8DAHtYdaO3du3Mb5Kzz YaqgVO88NDsYaQRJCnmdQ7KDFToMy5A6btj2LhnYQ/3CMhktkg2RHC0aERGgNJLs ifVj3kvc+l8UwomvNOMjNket+AH7hbp64lbAfjAwzcgOGROKNyOslsr33qibg4lQ SQKl15wFDHLAcP2tj9QoUFO+97FqDXWBIzoEhDDBqfpVNRx25R7NePUkkA+0dHTS VedeNG6p2yFeW2UTAD4nYP9xWA== =s7xn -----END PGP SIGNATURE----- Merge tag 'u-boot-stm32-20220510' of https://source.denx.de/u-boot/custodians/u-boot-stm Add new STM32 MCU boards and Documentation STM32 programmer improvements video: support several LTDC HW versions and fix data enable polarity board: fix stboard error message, consider USB cable connected when boot device is USB configs: stm32mp1: set console variable for extlinux.conf configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link ARM: stm32mp: Fix Silicon version handling and ft_system_setup() phy: stm32-usbphyc: Add DT phy tuning support arm: dts: stm32mp15: alignment with v5.18 ram: Conditionally enable ASR mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM pinctrl: stm32: rework GPIO holes management