Add the implementation for the CLK_GATE_SETCLR_INV and
CLK_GATE_NO_SETCLR flags.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
We either need to use IS_ENABLED(CONFIG_FOO) or CONFIG_IS_ENABLED(FOO).
IS_ENABLE(FOO) will always return false.
This commit fixes the comparison by using the CONFIG_IS_ENABLED(FOO)
syntax.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Some MediaTek SoC need an additional clock "source_cg". Enable
this new clock. We reuse the same clock name as in the kernel.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
It adds the driver for HIGMACV300 Ethernet controller found on HiSilicon
SoCs like Hi3798CV200. It's based on a downstream U-Boot driver, but
quite a lot of code gets rewritten and cleaned up to adopt driver model
and PHY API.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
It adds a Driver Model compatible reset driver for HiSlicon platform.
The driver implements a custom .of_xlate function, and uses .data field
as reset register offset and .id field as bit shift.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Make sure that we don't overflow the hose->regions array, otherwise we
would end up overwriting the hose->region_count field and cause mayhem
to ensue. Also print an error message when we'd be overflowing because
it indicates that there aren't enough regions available and the number
needs to be increased.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Allow the led bcm6858 driver to be used on bcm63158.
They have the same led controller.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
On response type r1b, if DTIME is not defined or too short,
the Datatimeout and DPSM flag occurs. Like the DPSM is
activated all next data transfer will be frozen.
To avoid this freeze:
-The driver must define a DTIME on all r1b response type.
-DTIME of SDMMC must be defined for alls stop transmission
(for read and write request) even if MMC_RSP_BUSY is not set.
-If busy timeout occur, an abort request must be sent to
reinitialize the DPSM.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Tested-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Initially the compatible string was wrongly set to "st,stm32f4xx-sdio".
Use compatible string used by kernel instead and identify mmci variant
using "arm,primecell-periphid" property.
Currently, the DM part of mmci driver is only used by STM32 SoCs,
that's why the switch case gets only one entry. It will be populated
easily with new variant in the future.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add basic support for the Amlogic G12A clock controller based on
the AXG driver.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
In order to support the Amlogic G12A clock controller,
re-architect the clock files into a meson directory.
No functionnal changes.
MAINTAINERS entry is also updated.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add pinctrl support for the Amlogic G12A SoC, which is
very similar to the Amlogic AXG support but with an additionnal
drive-strength register bank.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
When fixing sandbox test for regmap_read_poll_timeout(), the
sandbox_timer_add_offset was introduced but only defined in sandbox code
thus generating warnings when used out of sandbox :
include/regmap.h:289:2: note: in expansion of macro 'regmap_read_poll_timeout_test'
regmap_read_poll_timeout_test(map, addr, val, cond, sleep_us, \
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/meson_spifc.c:169:8: note: in expansion of macro 'regmap_read_poll_timeout'
ret = regmap_read_poll_timeout(spifc->regmap, REG_SLAVE, data,
^~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/meson_spifc.c: In function 'meson_spifc_txrx':
include/regmap.h:277:4: warning: implicit declaration of function 'sandbox_timer_add_offset' [-Wimplicit-function-declaration]
This fix adds a timer_test_add_offset() only defined in sandbox, and
renames the previous sandbox_timer_add_offset() to it.
Cc: Simon Glass <sjg@chromium.org>
Reported-by: Tom Rini <trini@konsulko.com>
Fixes: df9cf1cc08 ("test: dm: regmap: Fix the long test delay")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The driver add the support of the led IP on bcm6858.
This led IP can drive up to 32 leds, and can handle
blinking.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
In previously label which will be expanded to the node's full path was
used, and now replacing label with most commonly used DT phandle. The
codes were changed accordingly to the use of DT phandle and supporting
multiple instances.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Firmware loader would encounter problem if the block device is accessed
before initializing it. This patch would adding the support of probing
block device and initializing block before the block device is accessed by
firmware loader.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The option write-protect may only change on the kernel command line,
we add a property in the device tree to be more flexible.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
The parameter page isn't always in big endian, so we add
an option to choose the endiannes of the parameter page.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
The driver brcmnand come from linux kernel 4.18.
Only SoC bcm6838 and bcm6858 are supported.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Linux commit 97d90da8a88 ("mtd: nand: provide several helpers
to do common NAND operations")
This is part of the process of removing direct calls to ->cmdfunc()
outside of the core in order to introduce a better interface to execute
NAND operations.
Here we provide several helpers and make use of them to remove all
direct calls to ->cmdfunc(). This way, we can easily modify those
helpers to make use of the new ->exec_op() interface when available.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[miquel.raynal@free-electrons.com: rebased and fixed some conflicts]
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[Philippe Reynes: adapt code to u-boot and only keep new function]
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This fixes a disconnect issue detected with fastboot command, when using
dwc2 driver.
- On u-boot side:
uboot>$ fastboot 0
- On USB host PC side, few seconds after
PC>$ fastboot reboot # Get stuck, uboot target never reboots
By enabling DEBUG_ISR logs, the bus suspend interrupt is seen before the
PC command has been issued. When the USB bus suspend occurs, there's a HACK
that disables the fastboot (composite driver). Here is the call stack
upon USB bus suspend:
- dwc2_handle_usb_suspend_intr()
- dev->driver->disconnect()
- composite_disconnect()
- reset_config()
- f->disable()
- fastboot_disable()
- usb_ep_disable(f_fb->out_ep);
- usb_ep_disable(f_fb->in_ep);
.. other disable calls.
When the resume interrupt happens, everything has been disabled, then
nothing happens. fastboot command gets stuck on HOST side.
Remove original HACK, that disconnects the composite driver upon
USB bus suspend. Implement disconnect detection instead:
- check GINTSTS OTG interrupt
- read GOTGINT register
- check GOTGINT, SesEndDet bit (e.g. session end)
This is inspired by what is implemented currently in Linux dwc2 driver.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Our R-Car3 Android userspace relies on the output of 'fastboot
getvar platform' and U-Boot currently is not able to handle it:
host $> fastboot getvar platform
getvar:platform FAILED (remote: Variable not implemented)
finished. total time: 0.001s
We either have the option of adding 'fastboot.platform' variable
to the default/saved environment as a workaround or add proper
'fastboot getvar platform' support in U-Boot via this patch.
In the latter case, other platforms can benefit from it too.
Note that R-Car3 already exports 'platform' environment variable via
v2019.01 commit 00e4b57e9e71c3 ("ARM: rmobile: Set environment variable
containing CPU type").
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Where we have to compute partition names, rather than using a hardcoded
32 for the partition name length, replace with PART_NAME_LEN.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
The DK1 and DK2 boards use the USB Type-C controller STUSB1600.
This patch updates:
- the device tree to add the I2C node in the DT
- the board stm32mp1 to probe this I2C device and use this controller
to check cable detection.
- the DWC2 driver to support a new dt property
"u-boot,force-b-session-valid" which forces B session and
device mode; it is a workaround because the VBUS sensing and
ID detection isn't available with stusb1600.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Add compatible "st,stm32mp1-hsotg" and associated driver data to manage
the usb33d-supply and the ST specific register for VBus sensing.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
# Conflicts:
# drivers/usb/gadget/dwc2_udc_otg.c
Reviewed-by: Lukasz Majewski <lukma@denx.de>
All TX fifo size can be different, add tx_fifo_sz_array[]
into dwc2_plat_otg_data to be able to set them.
tx_fifo_sz_array[] is 17 Bytes long and can contains max 16
tx fifo size (synopsys IP supports max 16 IN endpoints).
First entry of tx_fifo_sz_array[] is the number of valid
fifo size the array contains.
In case of tx_fifo_sz_array[] doesn't contains the same
number of element than max hardware endpoint, display
a warning message.
Compatibility with board which doesn't use tx_fifo_sz_array[]
(Rockchip rk322x/rk3128/rv1108/rk3288/rk3036) is kept.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Some DWC2 ip variant doesn't use 16 hardware endpoint as hardcoded
in the driver. Bits INEps [29:26] of HWCFG4 register allows to get
this information.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Add a new function to check the session B validity, to be use to check
cable connection.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reset the hardware to be sure of the device state.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Minimal conversion to driver model by using the uclass
UCLASS_USB_GADGET_GENERIC based on:
- reset uclass
- clock uclass
- generic uclass.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Since its inception in upstream fastboot android-n-preview-1 [1],
"has-slot" option has never taken the form of "has_slot". Amongst the
users of "getvar has-slot:" is the upstream bootloadertest.py [2].
Current U-Boot "has_slot" version must be a typo. Fix it.
[1] https://android.googlesource.com/platform/system/core/+/a797479bd51c
("Fix fastboot variable name")
[2] https://android.googlesource.com/platform/system/extras/+/72de393e118e3
("Bootloader verification for AndroidThings.")
Fixes: f73a7df984a9 ("net: fastboot: Merge AOSP UDP fastboot")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Acked-by: Alex Kiernan <alex.kiernan@gmail.com>
USB_MUSB_TI requires USB_MUSB_DSPS, failing at link time if it's not
selected:
drivers/usb/musb-new/built-in.o: In function `ti_musb_host_ofdata_to_platdata':
drivers/usb/musb-new/ti-musb.c:193: undefined reference to `musb_dsps_ops'
or if OF_CONTROL is not selected:
arch/arm/mach-omap2/built-in.o:(.data.usb0+0x24): undefined reference to `musb_dsps_ops'
Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Add the DM_MMC-compatible DesignWare MMC driver support for Synopsys
ARC devboards. It is created to switch ARC devboards to use DM_MMC.
It required information such as clocks (Bus Interface Unit clock,
Card Interface Unit clock) and SDIO bus width.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
The generic timer count is an incrementing 64bit value and a timer driver
must return an incrementing 64bit value. The DW APB timer only provides a
32bit timer counting down, thus the result must be inverted and converted
to a 64bit value. The current implementation is however missing the 64bit
up-conversion and this results in random timer roll-overs, which in turn
triggers random timeouts throughout the codebase.
This patch adds the missing 64bit up-conversion to fix the issue.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
