[backport from Linux commit db4fc2c79c533986795a7750e9a12caf9d620b48]
As reported in the section 8.3 (i. e. Board revision history) of document
UM2033 (i. e. Discovery kit with STM32F769NI MCU) these are the changes
related to the board revision addressed by the patch:
- Board MB1166 revision A-09:
- LCD FRIDA FRD397B25009-D-CTK replaced by FRIDA FRD400B25025-A-CTK
The patch adds the DTS support for the new display which belongs to the
the Novatek NT35510-based panel family.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This patch adds i.MX95 19x19 EVK board basic support.
Messaging unit for EdgeLock Secure Enclave, messaging unit for System
Manager, uSDHC for SD Card, gpio, lpuart are supported now.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Nishanth Menon <nm@ti.com> says:
Just happened to get a BeagleY-AI at desk and happened to test master
branch (7dd49a9264 drivers: scsi: Add 'erase' support), noticed a few
issues which were rather easy to solve.. so, here we go:
Link: https://lore.kernel.org/r/20250425173120.141503-1-nm@ti.com
Just like TF-A and OP-TEE, the documentation states a custom path for DM
can be provided at build time by setting TI_DM. This should then set
ti-dm-path which updates ti-dm node filenames in binman.
Two issues prevent this from functioning for most K3 boards. One is when
then DM firmware name is inside a blob-ext node instead of a ti-dm node.
The second is when the filename in the ti-dm node is a pointer to a
blob-ext node. In this case even though the filename is updated, the
filename in the blob-ext is not, so build can fail if the default
file in the blob-ext cannot be found, even if the updated ti-dm file
does exist.
Fix both of these for all K3 by removing any indirect ti-dm nodes and
making sure all DM nodes are labeled with "ti-dm".
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
SeeedStudio BeagleBone Green Eco (BBGE) is a clone of the BeagleBone Green
(BBG). It has minor differences from the BBG, such as a different PMIC,
a different Ethernet PHY, and a larger eMMC.
The PMIC is not yet supported in mainline, but the work is ongoing.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Add the PMIC ESM node which is responsible for triggering the PMIC
reset.
Suggested-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Add the PMIC ESM node which is responsible for triggering the PMIC
reset.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
main_gpio1 controls the voltage for the SDcard from 3.3v to 1.8v.
This is required for proper operation of SDcard through various boot
stages.
Fixes the following seen in the boot log:
failed to set vqmmc-voltage to 3.3V
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Caleb Connolly <caleb.connolly@linaro.org> says:
Introduce a new event to signal that the live tree has been built,
allowing boards to perform fixups on the tree before devices are bound.
Crucially this allows for devices to be enabled or disabled, but also
allows for properties that are parsed during the bind stage to be
modified (such as dr_mode for dwc3).
With this in place, mach-snapdragon is switched over to use the event
and some hacky U-Boot specific DT overrides (which had to be undone
prior to booting an image) are removed in favour of fixing up the
livetree (which is not passed on to further boot stages).
Finally, some minor fixes are made for the QCM2290 RB1 board, the sdcard
is enabled and it now uses USB host mode in U-Boot like it's bigger
sibling the RB2.
Link: https://lore.kernel.org/r/20250411-livetree-fixup-v2-0-1236823377bb@linaro.org
The RB1 and RB2 have a single USB controller which is manually muxed
between a type-c port and an internal USB hub via a DIP switch. OTG is
supported in Linux, but the DWC3 driver in U-Boot can only handle a
single mode, and defaults to peripheral mode.
We did hack around this on the RB2, but the RB1 got left out.
Now that we can fix up the live tree before devices are bound, drop the
DTS hacks and do the fixup at runtime instead.
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Since commit b4734c9c33 ("clk: imx: Convert clock-osc-* back to osc_*")
SPL takes a long time to load U-Boot proper on an imx8mm-evk board.
The reason for the long delay is because the osc_32k clock is not available
in the SPL phase.
Fix this problem by passing the 'bootph-all' and 'bootph-pre-ram'
properties to make the osc_32k clock available in SPL.
This also aligns with imx8mn and imx8mp-u-boot.dtsi files.
Fixes: b4734c9c33 ("clk: imx: Convert clock-osc-* back to osc_*")
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Adam Ford <aford173@gmail.com>
Add led support, force default state on U-Boot initialization and put on
the Linux heartbeat led = "blue-led" during U-Boot execution.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Enable OF_UPSTREAM flag for STM32MP2 platforms.
Add fixed-clock ck_flexgen_08 and ck_icn_ls_mcu until STM32MP25
clock driver will be available.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The STM32 System Bus is an internal bus on which devices are connected.
ETZPC is a peripheral overseeing the firewall bus that configures
and control access to the peripherals connected on it.
For more information on which peripheral is securable, please read
the STM32MP13 or STM32MP15 reference manual.
Signed-off-by: Lionel Debieve <lionel.debieve@foss.st.com>
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Enable OF_UPSTREAM flag for STM32MP15 platforms, except for
stm32mp15-odyssey,see following patch :
"configs: stm32: introduce stm32mp15-odyssey_defconfig"
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Enable OF_UPSTREAM flag for STM32MP13 platforms.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Enable OF_UPSTREAM flag for STM32MPF4 platforms.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Enable OF_UPSTREAM flag for STM32F7 platforms.
Use upstream device tree for DSI and LTDC nodes,
As now in upstream DT, in panel@0 node, power-supply property is
present, which is a fixed-regulator, add DM_REGULATOR_FIXED flag
for stm32f769-disco boards.
Set also DEFAULT_FDT_FILE in defconfigs and use it in stm32f746-disco.h
to indicate which FDT file to load (All STM32F7 boards are using this
file).
If something is missing, it must be added in upstream device tree
in linux kernel ("px_clk" for DSI by example).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Enable OF_UPSTREAM flag for STM32H7 platforms.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Enable OF_UPSTREAM flag for stih410-b2260 board.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The bootph-all property in u-boot enables driver initialization prior to
relocation, this is necessary to use the device as boot media.
sdhci0 is the phandle for eMMC on am62a, so this change allows us to use
eMMC as a boot media.
Signed-off-by: Anshul Dalal <anshuld@ti.com>
Add a minimal generic RK3399 board that only have eMMC, SDMMC, SPI flash
and USB OTG enabled. This defconfig can be used to boot from eMMC,
SD-card or SPI flash on most RK3399 boards that follow reference board
design.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Christopher Obbard <christopher.obbard@linaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a minimal generic RK3328 board that only have eMMC, SDMMC, SPI flash
and USB OTG enabled. This defconfig can be used to boot from eMMC,
SD-card or SPI flash on most RK3328 boards that follow reference board
design.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Christopher Obbard <christopher.obbard@linaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The ROC-RK3576-PC is a SBC made by Firefly, designed around the RK3576
SoC. This adds the needed board infrastructure and config for it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Rockchip RK3576 is a ARM-based SoC with quad-core Cortex-A72
and quad-core Cortex-A53 including 6TOPS NPU, Mali-G52 MC3, HDMI Out,
DP, eDP, MIPI DSI, MIPI CSI2, LPDDR4/4X/5, eMMC5.1, SD3.0/MMC4.5, UFS,
USB OTG 3.0, Type-C, USB 2.0, PCIe 2.1, SATA 3, Ethernet, SDIO3.0, I2C,
UART, SPI, GPIO and PWM.
Add arch core support for it.
Signed-off-by: Xuhui Lin <xuhui.lin@rock-chips.com>
[adapted for mainline u-boot]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Radxa E20C is an ultra-compact network computer with a RK3528A SoC
that offers a wide range of networking capabilities.
Features tested on a Radxa E20C v1.104:
- SD-card boot
- eMMC boot
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a minimal generic RK3528 board that only have eMMC and SD-card
enabled. This defconfig can be used to boot from eMMC or SD-card on most
RK3528 boards that follow reference board design.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a rk3528-u-boot.dtsi extending the basic dts/upstream rk3528.dtsi
with bare minimum nodes to have a booting system from eMMC and SD-card.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Linux commit 6ee0b9ad3995 ("arm64: dts: rockchip: Add rng node to
RK3588") merged for v6.15-rc1 add a proper rng node to the device tree.
The compatible used differs compared to what U-Boot is currently using.
Replace the old trngv1 compatible with the dts/upstream compatible in
the rng driver and remove the old rng node compatible override from SoC
u-boot.dtsi to keep rng working after the driver change.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Linux commit afeccc408496 ("arm64: dts: rockchip: add DT entry for RNG
to RK356x") merged for v6.12-rc1 add a proper rng node to the SoC DT.
Remove the rng node from SoC u-boot.dtsi now that the rng driver support
the compatible used in dts/upstream DT. Ensure the rng node is enabled
to support rng on RK3566 variants.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
I don't see a reason why this should only be enabled on a per-board
basis. The rng IP is inside the SoC and doesn't seem to rely on anything
external to it, therefore let's enable it on the SoC DTSI and remove the
now empty px30-evb-u-boot.dtsi.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In-line ECC support was added for LPDDR by reserving the last one-eighth
of the memory space for ECC data. Full memory initialization using the
BIST MEM INIT mailbox command, based on address and size, is required to
correctly generate ECC data and enable proper ECC logic verification.
Signed-off-by: Tingting Meng <tingting.meng@altera.com>
Cache allocation for dirty writes in the CCU system cache was disabled
for performance optimization.
Signed-off-by: Tingting Meng <tingting.meng@altera.com>
Use GPIO hogging method in device tree to set SDIO_SEL pin (portb3)
direction as output with value 0 after power-on reset.
This is to ensure stable 0V voltage reading from SDIO_SEL GPIO pin
after board init.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Load and entry addresses are corrected for Agilex5 SoCFPGA board
which would enable to generate the kernel itb file with the right
addresses.
Signed-off-by: Naresh Kumar Ravulapalli <nareshkumar.ravulapalli@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
-----BEGIN PGP SIGNATURE-----
iQFNBAABCgA3FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmgF7EUZHGV1Z2VuLmhy
aXN0ZXZAbGluYXJvLm9yZwAKCRAesx4CDqwvyEUYB/sFVmoELCerP0Dwonec1C2V
oV9qqiwEpaGC47O79aaRCeR5mWvPA3Zddr5lVSpRVTKmF75/+hqTN/DbjoSqVYIh
DcW4A//dxejnpIo6p9yS4860N/mMQPK7n/VHRX6mY/iN0CrmtGD/gKWpaQKyZNHS
tq+K5vOf9vdKe/sbEWIDKnTodQQkecl8Z1Fl3lbaoxqPKuYtnD1o8YXPSx++qu6Q
7UFd4X03sFI4P6tV960IMQCAr9jW7qGckF2EHGwPme6YHnjgPfBGmE7uK3N12PJ2
PnMFapTPpdydUPjRZcE+x9TdYYUiwGCPlJFpwuTQpomb6D7gbCQzC2gP82T1KBUt
=5oSx
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2025.07-b' of https://source.denx.de/u-boot/custodians/u-boot-at91
Second set of u-boot-at91 features for the 2025.07 cycle:
This feature set includes the addition of sam9x60 usb gadget, and a fix
for sama5d2 SPL.
The PIT timer needs to be available early in the SPL phase,
otherwise SPL fails to boot and only prints:
Could not initialize timer (err -96)
Fix this problem by passing 'bootph-all' to the sama5d2 PIT node.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Add the USB gadget DT node for the sam9x60 SoC's.
Signed-off-by: Zixun LI <admin@hifiphile.com>
Reviewed-by: Eugen Hristev <eugen.hristev@linaro.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Add eMMC nodes with the fixed regulator and fixed clock. It's also
needed to assign the clock and set it to 200MHz as it's set to 150Mhz by
default.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This commit adds support for the brcp1, brsmarc2, brcp150 and brcp170
boards. This boards are based on the Xilinx Zynq SoC.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20250404072819.69642-5-bernhard.messerklinger@br-automation.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
