All of the PCI/PCI-Express driver and initialization code that
was in the MPC8641HPCN port has now been moved into the common
drivers/fsl_pci_init.c. In a subsequent patch, this will be
utilized by the 85xx ports as well.
Common PCI-E IMMAP register blocks for FSL 85xx/86xx are added.
Also enable the second PCI-Express controller on 8641
by getting its BATS and CFG_ setup right.
Fixed a u16 vendor compiler warning in AHCI driver too.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Add the ability for modules from the Schindler cm5200 family to use a
single U-Boot image:
- rename cm1_qp1 to cm5200
- add run-time module detection
- parametrize SDRAM configuration according to the module we are running on
Few minor, board-specific fixes included in this patch:
- better MAC address handling
- updated default environment ('update' command uses +{filesize} now)
- improved error messages in the auto-update code
- allow booting U-Boot from RAM (CFG_RAMBOOT)
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Signed-off-by: Piotr Kruszynski <ppk@semihalf.com>
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
Changed storage type of cfg_simulate_spd_eeprom to const
Changed storage type of gpio_tab to stack storage
(Cannot access global data declarations in .bss until afer code relocation)
Improved SDRAM tests to catch problems where data is not uniquely addressable
(e.g. incorrectly programmed SDRAM row or columns)
Added CONFIG_PROG_SDRAM_TLB to support Bamboo SIMM/DIMM modules
Fixed AM29LV320DT (OpCode Flash) sector map
Signed-off-by: Eugene OBrien <eugene.obrien@advantechamt.com>
Signed-off-by: Stefan Roese <sr@denx.de>
- Clear ECC status regs after ECC POST test
- Set dcbz for ECC generation with caches enabled as default
- Code cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
Change Lime SDRAM initialization to now support 100MHz and
133MHz (if enabled). Also the framebuffer is initialized to
display a blue rectangle with a white border.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds ECC Post test for the Lwmon5 board based
on PPC440EPx to U-Boot.
Signed-off-by: Pavel Kolesnikov <concord@emcraft.com>
Acked-by: Yuri Tikhonov <yur@emcraft.com>
Acked-by: Stefan Roese <sr@denx.de>
This patch fixes the negative consequences for 8xx of the recent
"ppc4xx: Clean up 440 exceptions handling" commit.
Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
The new function remove_tlb() can be used to remove the TLB's used to
map a specific memory region. This is especially useful for the DDR(2)
setup routines which configure the SDRAM area temporarily as a cached
area (for speedup on auto-calibration and ECC generation) and later
need this area uncached for normal usage.
Signed-off-by: Stefan Roese <sr@denx.de>
Made the boot commands use device trees by default.
Also moved the ramdisk to 1000000 (I think the previous address
was getting overridden during boot).
Signed-off-by: Andy Fleming <afleming@freescale.com>
* Adds code to modify CPM frequencies
* Cleans up the config file to #define TSEC and (for now) #undef FCC
* Adds the MII command for all 8560 ADS configurations
* Updates config file to provide convenience commands for booting
with a device tree
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
- now the Flash ST M29W040B is supported (not tested)
- fix the "led" command
- fix compile error, if BUILD_DIR is used
Signed-off-by: Heiko Schocher <hs@denx.de>
Enabled cache in cpu_init_f() for faster flash to mem allocation. Updated cache handling in start.S. Applied cache invalidate in fec_send() and fec_recv(). Added CFG_UNIFY_CACHE for CF V3 only.
Signed-off-by: TsiChung <tcliew@Goku.(none)>
Since it is already in m68k folder, un-necessary to pad mcf. Replaced immap_5329.h and m5329.h to immap.h
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Create new header file to include immap_5xxx.h and m5xxx.h and to share among drivers without update in driver file each processor is added. Moved peripherals base address and defines from configs file to immap.h.
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Explicitly add in default CONFIG_BOOTP_* options where cmd_confdefs.h
used to be included but CONFIG_BOOTP_MASK was not defined.
Remove lingering references to CFG_CMD_* symbols.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Explicitly add in default CONFIG_BOOTP_* options where cmd_confdefs.h
used to be included but CONFIG_BOOTP_MASK was not defined.
Remove lingering references to CFG_CMD_* symbols.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Explicitly add in default CONFIG_BOOTP_* options where cmd_confdefs.h
used to be included but CONFIG_BOOTP_MASK was not defined.
Remove lingering references to CFG_CMD_* symbols.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
