Instead of having a peripheral clock of 50 MHz like the BCM63xx family, it
has a 48 MHz clock.
This fixes uart baud rate calculation for BCM3380.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This driver allows rebooting the SoC by calling wdt_expire_now op.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver allows rebooting the SoC by calling wdt_expire_now op.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver allows rebooting the SoC by calling wdt_expire_now op.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver controls the watchdog present on this SoC.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver controls the watchdog present on this SoC.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver controls the watchdog present on this SoC.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce the imx_set_perclk() function to make it possible to set the
PER clocks.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
imx_get_perclk() used the AHB clock as the clock source for all PER
clocks, but the USB PLL output can also be a PER clock source if the
corresponding PER CLK MUX bit is set in CCM.MCR.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
There is no dedicated reset signal wired up for the MX6QDL thus if the
bootloader enables the link we need some special handling to get the core
back into a state where it is safe to touch it for configuration.
While there has been some special handling in the Linux kernel to do this,
it was removed in 4.11 thus we need to do it properly in the bootloader
and therefore without this if you enable PCI in the bootloader you will hang
while booting the 4.11 kernel.
This puts the PCIe controller back into a safe state for the kernel driver
before launching the kernel.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Peter Senna Tschudin <peter.senna@collabora.com>
Add the initial support for pico-imx7d board based on Wig Cheng's
source code.
Add support for eMMC, USB gadget, I2C, PMIC and Ethernet.
For more information about this board, please visit:
http://www.technexion.org/products/pico/pico-som/pico-imx7-emmc
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The dram_init and dram_init_banksize functions were using a board
specific implementation for decoding the memory banks from the fdt.
This change makes the dram_init* functions use a generic implementation
of decoding and populating memory bank and size data.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nathan Rossi <nathan@nathanrossi.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables the mvpp2 port 0 usage on the Armada 7k DB by setting
the correct PHY type (KR / SFI) for the COMPHY driver and enabling the
ethernet0 device node in the dts.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Start to populate the device tree of the Armada 37xx with the pincontrol
configuration used on the board providing a dts.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Add the nodes for the two pin controller present in the Armada 37xx SoCs.
Initially the node was named gpio1 using the same name that for the
register range in the datasheet. However renaming it pinctr_nb (nb for
North Bridge) makes more sens.
Minor changes for U-Boot because of the slightly different dts version
done by Stefan Roese.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Update the NanoPi Neo device tree file to use the NanoPi dtsi.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
NanoPi M1 is a board based on Allwinner H3 CPU.
This commit adds the support for this platform with:
- an include device tree which enables UART, LEDs, GPIO key switch,
1 USB host ports and the SD-card as a dtsi file.
- a device tree specific to this board that enables the
2 additional USB ports
- a defconfig file for minimal support
- a section in MAINTAINERS (add myself)
Synchronized with the kernel device tree, from commits:
sun8i-nanopi.dtsi: 85d2913614d9ab899d23b7ab7d22d23cf45bd1de
sun8i-h3-nanopi-m1.dts: 10efbf5f16336b7540ad6a16aa1cb0b26bab033b
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This patch is to adjust the memory mapping for FLash/SD card on
LS1043AQDS and LS1043ARDB, such as PPA firmware load address, FMAN
firmware load address, QE firmware load address, U-Boot start address
on serial flash and environment address.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2081ARDB board is similar to LS2080ARDB board with few differences
It hosts LS2081A SoC
Default boot source is QSPI-boot
It does not have IFC interface
RTC and QSPI flash device are different
It provides QIXIS access via I2C
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The QorIQ LS2081A SoC has eight 64-bit ARM v8 Cortex A72 cores and
is built on layerscape architecture. It is 40-pin derivative of
LS2084A (non-AIOP personality of LS2088A). So feature-wise it is
same as LS2084A. LS2041A is a 4-core personality of LS2081A.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QSPI-boot is supported on LS2088ARDB RevF board with LS2088A SoC.
LS2088ARDB RevF Board has limitation that QIXIS can not be accessed.
CONFIG_FSL_QIXIS is not enabled.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2080ARDB/LS2088ARDB RevF board has smart voltage translator
which needs to be programmed to enable high speed SD interface
by setting GPIO4_10 output to zero.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
trini: Make Kconfig SPL_xxx entires only show if SPL, so that we don't
get Kconfig errors on platforms without SPL, ie sandbox (without SPL).
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_IMMAP
Also move this command out of the cmd/ directory since it is
PowerPC-specific.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present IDE support is controlled by CONFIG_CMD_IDE. Add a separate
CONFIG_IDE option so that IDE support can be enabled without requiring
the 'ide' command.
Update existing users and move the ide driver into drivers/block since
it should not be in common/.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_CMD_HDMIDETECT
Note that we cannot do 'default y if VIDEO' because this option is only
enabled for a small subset of mx6 boards. Also this command is is not a
great implementation (it doesn't use driver model).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_HASH
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Rework slightly, enable on some boards again]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_FPGA_LOADBP
CONFIG_CMD_FPGA_LOADFS
CONFIG_CMD_FPGA_LOADMK
CONFIG_CMD_FPGA_LOADP
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_CMD_ESBC_VALIDATE
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
