Allowing multicast packets is required for IPv6 neighbor discovery
protocol.
Signed-off-by: Parvathi Bhogaraju <pbhogaraju@microsoft.com>
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
In IPv6 context, the ICMP and UDP checksum byte in the RX packet
is initially set to 0, recaclculated, and then re-inserted.
This process can result in a dirty cache line. To prevent issues,
it is essential to invalidate cache for the RX buffer before freeing
the descriptor for next DMA transfer.
This ensure that the dirty cache line doesn't inadvertently written back
due to cache eviction, there by corrupting the RX buffer
Signed-off-by: Parvathi Bhogaraju <pbhogaraju@microsoft.com>
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
MD Danish Anwar <danishanwar@ti.com> says:
Introduce ICSSG PRUETH support in uboot. The ICSSG driver is used in TI
AM654 SR2.0.
The ICSSG PRU Sub-system runs on EMAC firmware. This series Introduces
support for ICSSG driver in uboot.
This series has been tested on AM65x SR2.0, and the ICSSG interface is
able to ping / dhcp and boot kernel using tftp in uboot.
To use ICSSG2 ethernet, the ICSSG firmware needs to be loaded to PRU RPROC
cores and RPROC cores need to be booted with the firmware. This step is
done inside driver similar to kernel.
The remoteproc driver uses request_fw_into_buf() API from fs-loader driver
to load and start rproc with the required firmwares.
This series only introduces driver files. The device tree and config
changes to enable ICSSG driver will be introduced later.
ICSSG firmware supports FDB commands. Add support to send FDB commands
from driver. Once rx_flow_id is obtained from dma, let firmware know that
we are using this rx_flow_id by sending a FDB command.
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
This is the PRUSS Ethernet driver for TI AM654 SR2.0 and later SoCs with
the ICSSG PRU Sub-system running EMAC firmware. ICSSG Subsystem supports
two slices per instance. This driver caters to both slices / ports of
the icssg subsystem.
Since it is not possible for Ethernet driver to register more than one
port for a given instance, this patch introduces top level PRUETH as
UCLASS_MISC and binds UCLASS_ETH to individual ports in order to support
bringing up more than one Ethernet interface in U-Boot.
Since top level driver is UCLASS_MISC, board files would need to
instantiate the driver explicitly.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Add icssg_queue.c file. This file introduces macros and APIs related to
ICSSG queues. These will be used by ICSSG Ethernet driver.
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Add icssg_config.h / .c and icssg_classifier.c files. These are firmware
configuration and classification related files. Add MII helper APIs and
MACROs. These APIs and MACROs will be later used by ICSSG Ethernet driver.
Also introduce icssg_prueth.h which has definition of prueth related
structures.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Add firmware interface related headers and macros for ICSSG Ethernet
driver. These macros will be later used by the ICSSG ethernet driver.
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
The device name is a concatenation of the device node name of the cpsw
device and of the device node name of the port. In my case that is
ethernet@8000000
port@1
First the buffer is really too small, but more importantly, there is no
boundary check. Use snprintf() and increase the buffer size.
Fixes: 38922b1f4a ("net: ti: am65-cpsw: Add support for multi port independent MAC mode")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Missing line-feeds in error messages lead to output like:
phy_startup() failed: -110FAILED: -110=>
Output like the following is much easier to read:
phy_startup() failed: -110
FAILED: -110
=>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Change to regulator_set_enable_if_allowed to avoid enable failure,
in case same phy supply shared by multiple FEC controllers.
Signed-off-by: Ye Li <ye.li@nxp.com>
Pull the PHY GPIO reset code into separate function, since
this is and will be reused multiple times. Set up default
reset assert and deassert timing to generous 20ms and 1ms
for maximum compatibility in case those DT properties are
missing.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
From the ethernet header is not on aligned, because the length
of the ethernet header is 14 bytes.
Therefore, unaligned access must be done here.
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
There is no need to perform the endian twice here.
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
shrink the first argument of log_msg_ret(), add dev_xxx() functions for
error reporting.
Fixes: 9d8f78a2a7 ("net: add hifemac Ethernet driver for HiSilicon platform")
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
The initial commit used log_msg_ret() wrongly. Fix that by moving error
report to a separate dev_err() call and shrink the first argument of
log_msg_ret() to no more than 4 chars.
Fixes: 6b5c8d98e2 ("net: add hifemac_mdio MDIO bus driver for HiSilicon platform")
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
As with fixed-link phy device, the NC-SI phy devive does not
require an mdio bus. So, a condition is added to check the
NC-SI phy id to avoid accessing the bus pointer that is NULL.
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
Booting R-Car Gen3 arm64 U-Boot with CONFIG_UBSAN=y resulted in:
=====================================================================
UBSAN: Undefined behaviour in drivers/net/phy/phy.c:728:19
left shift of 1 by 31 places cannot be represented in type 'int'
=====================================================================
Fix it by appending the UL suffix to the numeric literal. While at it,
convert the type of "addr" variable from signed to unsigned, to protect
against shifting the numeric literal by a negative value (which would
lead to yet another undefined behavior).
Fixes: 1adb406b01 ("phy: add phy_find_by_mask/phy_connect_dev")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
* Using U-suffix for integer is sufficient.
* ffs() of non-zero value cannot be 0. But addr being unsigned is
* preferable.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Configure LEDs on BCM54210E so they would blink on activity
and indicate link speed. Without this the LEDs are always on
if cable is plugged in.
Signed-off-by: Marek Vasut <marex@denx.de>
The issue occurs the UAF (use-after-free) to cause double free
when do the realloc function for the pointers during the
reinitialization NC-SI process, and it will cause the memory
management occurs error.
So, nullify these pointers after free.
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
The different macros use writel which is defined in asm/io.h, so let's
include the header so users of hardware.h do not need to include
asm/io.h as well.
While at it, remove asm/io.h includes wherever
asm/arch-rockchip/hardware.h is included already.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
In case the PHY is fully described in DT, use PHY MDIO address
from DT directly instead of always using auto-detection. This
also fixes the behavior of 'mdio list' in such DT setup, which
now prints the PHY connected to the MAC correctly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Add a new Kconfig symbol MDIO_TI_CPSW for the CPSW MDIO
driver and build it with proper DM support if enabled.
If MDIO_TI_CPSW is not enabled then we continue to
behave like before.
Clean up MDIO custom handling in am65-cpsw and use
dm_eth_phy_connect() to get the PHY.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Tested-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
The mv88e6xxx driver does not currently initialize the smi_addr field, but
instead keeps the default zero value. This leads to driver being unusable
on devices where the switch is not on address zero of the mdio bus. Fix
this problem by reading the SMI address from device tree.
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Rename RMOBILE_CPU_TYPE_* to RENESAS_CPU_TYPE_* because all
the chips are made by Renesas, while only a subset of them is
from the R-Mobile line.
Use the following command to perform the rename:
"
$ git grep -l '\<RMOBILE_CPU_TYPE_[A-Z0-9]\+\>' | \
xargs -I {} sed -i 's@\<RMOBILE\(_CPU_TYPE_[A-Z0-9]\+\)\>@RENESAS\1@g' {}
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Rename rmobile_get_cpu_type() to renesas_get_cpu_type() because
all the chips are made by Renesas, while only a subset of them
is from the R-Mobile line.
Use the following command to perform the rename:
"
$ git grep -l '\<rmobile_get_cpu_type\>' | \
xargs -I {} sed -i 's@\<rmobile_get_cpu_type\>@renesas_get_cpu_type@g' {}
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
The actual driver does not work when there is no linked PHY. These
changes add support for fixed-link feature in the device tree.
Signed-off-by: BELOUARGA Mohamed <m.belouarga@technologyandstrategy.com>
Some platforms (such as the Lichee Pi 4A) have their dwmac device
addressable only in high memory space. Storing the node's base address
on 32 bits is not possible in such case.
Use platform's physical address type to store the base address.
Signed-off-by: Nils Le Roux <gilbsgilbert@gmail.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Rename nxp_c45_tja11xx structure to nxp_c45_tja1103. The driver will
support more PHYs and nxp_c45_tja11xx is too generic.
Signed-off-by: "Radu Pirea (NXP OSS)" <radu-nicolae.pirea@oss.nxp.com>
Read PHY speed from hardware instead of assuming 100Mbps by default.
The TJA1103 works only at 100Mbps, but the driver will support more PHYs.
Signed-off-by: "Radu Pirea (NXP OSS)" <radu-nicolae.pirea@oss.nxp.com>
Use a local definition for the PHY features. PHY_100BT1_FEATURES are
not defined using the 100BaseT1 bit, so keep this workaround in the driver.
Signed-off-by: "Radu Pirea (NXP OSS)" <radu-nicolae.pirea@oss.nxp.com>
Some ethernet PHY require being reset before a phy-id can be read back
on the MDIO bus. This can result in the following message being show
on e.g. a Radxa ROCK Pi E v1.21 with a RTL8211F ethernet PHY.
Could not get PHY for ethernet@ff540000: addr -1
Add support to designware ethernet driver to reset eth phy by calling
the eth phy uclass function eth_phy_set_mdio_bus(). The call use NULL
as bus parameter to not set a shared mdio bus reference that would be
freed when probe fails. Also add a eth_phy_get_addr() call to try and
get the phy addr from DT when DM_MDIO is disabled.
This help fix ethernet on Radxa ROCK Pi E v1.21:
=> mdio list
ethernet@ff540000:
1 - RealTek RTL8211F <--> ethernet@ff540000
Reported-by: Trevor Woerner <twoerner@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This ports the pad drive strength register configuration which can be
already found in the Linux driver for this PHY.
Signed-off-by: Lukasz Tekieli <tekieli.lukasz@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Make the "phy-handle" property optional, which allows support
for a fixed-link phy configuration.
Thus if the "phy-handle" is present in a DT, then driver will work as
before. Otherwise, phyaddr initialization will not be necessary,
as it is not needed in case of a fixed-link config.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
debug print delays reset of the driver. Finally I see
bunch of "rx error FFFF" errors in the screen. CI can
not handle many prints. While network works fine there
Reproduced with:
make CROSS_COMPILE=sh2-linux- r2dplus_defconfig all
qemu-system-sh4 -M r2d -nographic -serial null \
-serial mon:stdio -net user,tftp=`pwd` \
-net nic,model=rtl8139 -kernel ./u-boot.bin
Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
return value of smc911x_send is ignored, but on sucesseful
send we need return 0 and or error -ETIMEOUT, not opposite.
Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In order to make it easier to move on to dropping common.h from code
directly, remove common.h inclusion from the rest of the header file
which had been including it.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Port the mdio-mux-meson-gxl.c Linux driver introduced in [1],
and adapt it to U-Boot.
This driver is needed to boot U-Boot with Linux DT since v6.4,
since it switched the MDIO mux from the mmio to a proper GXL driver.
[1] 9a24e1ff4326 ("net: mdio: add amlogic gxl mdio mux support")
Link: https://lore.kernel.org/r/20231213-u-boot-gxl-mdio-mux-v2-1-c56bb02a75ea@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add support for DWC EQoS MAC on i.MX93.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
As per the xlnx,axi-ethernet-1.00.a DT documentation in linux, the AXI
DMA registers can be obtained via the reg property or via a separate
node for the axistream DMA controller. Currently only the latter is
supported, so add support to fetch the DMA controller registers from the
"reg" property.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20231116164024.139934-1-mchitale@ventanamicro.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
DM_GPIO is always enable in U-Boot proper for ARCH_SUNXI, and this
driver is never enabled in SPL, so the condition is always true.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Older DesignWare Ethernet MAC versions that this driver supports can
only work with 32-bit DMA source/destination addresses. Some platforms
have no physical RAM at the lowest 4GB address space. For these
platforms the driver must translate DMA addresses to/from physical
memory addresses.
Call translation routines so that properly configured platforms can use
the DesignWare Ethernet MAC. For platforms using device-tree this
usually means adding dma-ranges property to the bus the device node is
in.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
e1000_eth_ids holds compatible strings for e1000 devices, but it
is meaningless as e1000 is a PCI device and there is no such
compatible string assigned to e1000 by the DT bindings community.
Drop it.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Setting the clock delay from the device tree settings
rx-internal-delay-ps and tx-internal-delay-ps was broken:
- The expected value in the device tree is suppose to be a
delay in picoseconds, but the driver only allowed an array index.
- Driver converted this array index to the actual delay in
picoseconds and tried to apply this in the device register. This
however is not a valid register value. The actual logic here was
reversed, it converted an register representation of the delay to
the device tree delay in picoseconds.
Only when the internal delays were NOT configured in the device tree
and they default value of 7 (=2000ps) was used, a valid value was
loaded in the register.
Signed-off-by: Frank de Brabander <debrabander@gmail.com>
It adds the driver for the internal MDIO bus of HIFEMAC Ethernet
controller. It's based on the mainstream linux driver.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
It adds the driver for HIFEMAC Ethernet controller found on HiSilicon
SoCs like Hi3798MV200. It's based on the mainstream linux driver, but
quite a lot of code gets rewritten and cleaned up to adopt u-boot driver
model.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Marvell LinkStreet switches support Clause 45 MDIO on the internal bus.
C45 read or writes require the register address to be written first to
the SMI PHY Data register, and then a special C45 Write Address Register
OP is used on the SMI PHY Register before making a C45 Read Data Register
OP and being able to actually read the register.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Driver is currently defining the mask and bit shifting itself,
there is no need for that as U-Boot has generic bitfield macros that help
us achieve the same result but in a cleaner way.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Add optional reset control, especially for the Aspeed SOC. For the
hardware without a reset line, the reset assertion/deassertion will be
skipped.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Set upper 32bit address for DMA descriptors and buffer address to support
64-bit addressing.
Signed-off-by: Ley Foon Tan <leyfoon.tan@starfivetech.com>
The CONFIG_MACPWR Kconfig symbol is used to point to a GPIO that enables
the power for the Ethernet "MAC" (mostly PHY, really).
In the DT this is described with the phy-supply property in the MAC DT
node, pointing to a (GPIO controlled) regulator. Since we need Ethernet
only in U-Boot proper, and use a DM driver there, we should use the DT
instead of hardcoding this.
Add code to the sun8i_emac and sunxi_emac drivers to check the DT for
that regulator and enable it, at probe time. Then drop the current code
from board.c, which was doing that job before.
This allows us to remove the MACPWR Kconfig definition and the respective
values from the defconfigs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Sam Edwards <CFSworks@gmail.com>
At the moment the sun4i EMAC driver relies on hardcoded CONFIG_MACPWR
Kconfig symbols to enable potential PHY regulators. As we want to get rid
of those, we need to find the regulator by chasing up the DT.
The sun4i-emac binding puts the PHY regulator into the MDIO node, which
is the parent of the PHY device. U-Boot does not have (and does not
need) an MDIO driver, so we need to chase down the regulator through the
EMAC node: we follow the "phy-handle" property to find the PHY node,
then go up to its parent, where we find the "phy-supply" link to the
regulator. Let U-Boot find the associated regulator device, and put that
into the private device struct, so we can find and enable the regulator
at probe time, later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
clk:
- remove additional compatible strings for Versal NET
net:
- zynq_gem: Fix clock calculation for MDC for higher frequencies
pinctrl:
- core: Extend pinmux status buffere size
- zynqmp driver: Show also tristate configuration
test:
- add test case for pxe get
Xilinx:
- describe SelectMAP boot mode
Zynq:
- Fix nand description in DT
ZynqMP:
- DTS sync patches with kernel and also W=1 related fixes
- Add support for KD240, zcu670, e-a2197 with x-prc cards, SC revB/C with i2c
description for other SC based boards
- k24 psu_init cleanup
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZSjvwAAKCRDKSWXLKUoM
IR34AJ92oum3pJXKxKREEZh0dCfDvJlE/wCggyzxI2T5liJfRG5jzlUuDjiLLU0=
=u1bz
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2024.01-rc1-v3' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2024.01-rc1 v3
clk:
- remove additional compatible strings for Versal NET
net:
- zynq_gem: Fix clock calculation for MDC for higher frequencies
pinctrl:
- core: Extend pinmux status buffere size
- zynqmp driver: Show also tristate configuration
test:
- add test case for pxe get
Xilinx:
- describe SelectMAP boot mode
Zynq:
- Fix nand description in DT
ZynqMP:
- DTS sync patches with kernel and also W=1 related fixes
- Add support for KD240, zcu670, e-a2197 with x-prc cards, SC revB/C with i2c
description for other SC based boards
- k24 psu_init cleanup
As the xlnx,phy-type device tree property is deprecated and phy-mode
is being used, so removing the code references of xlnx,phy-type.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231010030436.11854-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for declaring in device tree the reserved memory ranges
required for MC. Since the MC firmware acts as any DMA master present
in the SoC, the reserved memory ranges need also be identity mapped
in the SMMU, so create the required 'iommu-addresses' property in
the reserved memory nodes.
For now this support is used only on LX2160A SoCs.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
MDC clock change needs to be done when the driver probe function
is called as mdio is enabled at probe and not when the ethernet starts.
Setup the MDC clock at the probe itself.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230922045010.22852-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add rk_gmac_ops and other special handling that is needed for GMAC to
work on RK3588.
rk_gmac_ops was ported from linux commits:
2f2b60a0ec28 ("net: ethernet: stmmac: dwmac-rk: Add gmac support for rk3588")
88619e77b33d ("net: stmmac: rk3588: Allow multiple gmac controller")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add a new glue driver for Rockchip SoCs, i.e RK3568, with a GMAC based
on Synopsys DWC Ethernet QoS IP.
rk_gmac_ops was ported from linux commit:
3bb3d6b1c195 ("net: stmmac: Add RK3566/RK3568 SoC support")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Remove spam of RX packet not available debug messages when waiting to
receive a packet.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Return error code when phy_connect fails or no link can be established.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
rx_pkt is allocated and not used for anything, remove it.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This old patch was marked as deferred. Bring it back to life, to continue
towards the removal of common.h
Move this out of the common header and include it only where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
The NETSEC GMAC occasionally falls into a weird state where
MAC_REG_DESC_SOFT_RST has never been cleared and shows errors like the
below when networking commands are issued:
=> ping 192.168.1.1
ethernet@522d0000 Waiting for PHY auto negotiation to complete... done
netsec_wait_while_busy: timeout
Using ethernet@522d0000 device
ARP Retry count exceeded; starting again
ping failed; host 192.168.1.1 is not alive
It happens on not only 'ping' but also 'dhcp', 'tftp' and so on.
Luckily, restarting the NETSEC GMAC and trying again seems to fix the
problematic state. So first ensure that we haven't entered the state by
checking MAC_REG_DESC_SOFT_RST to be cleared; otherwise, restarting
NETSEC/PHY and trying again would work as a workaround.
Signed-off-by: Ryosuke Saito <ryosuke.saito@linaro.org>
Tested-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Current code expects bridge phy address at 0 which is not correct
expectation because bridge phy address is configurable.
That's why update the code to read reg property to figure it out
where bridge is and use it in phy creation code.
Signed-off-by: Tejas Bhumkar <tejas.arvind.bhumkar@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20230915045043.4167628-1-tejas.arvind.bhumkar@amd.com
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The documentation for struct phy state that "The content of the
structure is managed solely by the PHY API and PHY drivers".
Change to use the generic_phy_valid() helper to check if phy is valid.
Fixes: 10c50b1fac ("net: zynq: Add support for PHY configuration in SGMII mode")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
It's Broadcom PHY simply described as single-port
RGMII 10/100/1000BASE-T PHY. It requires disabling
delay skew and GTXCLK bits.
BCM54210E support ported from Linux kernel commit
0fc9ae1076697 ("net: phy: broadcom: add support for BCM54210E")
AUX/SHD/bcm54xx_config_clock_delay update ported from Linux 6.5-rc4 commit
28e219aea0b9e ("net: phy: broadcom: drop brcm_phy_setbits() and use phy_set_bits() instead")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Rafał Miłecki <rafal@milecki.pl>
The YT8511 ethernet PHYs can be found on e.g. the SOQuartz or
the Quartz64. Add rudimentary support for them.
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Enhance the AM65 CPSW NUSS driver to perform a MDIO reset using a GPIO
line. Logic is also added to perform a pre and post delay around reset
using the optional 'reset-delay-us' and 'reset-post-delay-us' properties.
This is similar to the reset being performed in the Linux kernel. The
reset is done once when the CPSW MDIO bus is being initialized.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
This patch adds support for MediaTek MT7988.
MT7988 features MediaTek NETSYS v3, including three GMACs, and two
of them supports 10Gbps USXGMII.
MT7988 embeds a MT7531 switch (not MCM) which supports accessing
internal registers through MMIO instead of MDIO.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
MT7981 has its GMAC2 PHY shared with USB3. To enable GMAC2, mux
register must be set to connect the SGMII phy to GMAC2.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Existing SGMII support of mtk-eth is actually a MediaTek-specific
2.5Gbps high-speed SGMII (HSGMII) which does not support
auto-negotiation mode.
This patch adds SGMII 1Gbps auto-negotiation mode and rename the
existing HSGMII to 2500basex.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
mt7531_mmd_ind_read and mt753x_switch_init are defined without static.
Since they're not used outside this file, we should add them back.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
fixup to add static qualifier
The original direct MDIO clause 45 access via SoC is missing the
data output. This patch adds it back to ensure MDIO clause 45 can
work properly for external PHYs.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Not all switches requires 1 second delay after deasserting reset.
MT7531 requires only maximum 200ms.
This patch defines dedicated reset wait time for each switch chip, and will
significantly improve the boot time for boards using MT7531.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
So far the switch is initialized in probe stage and is connected to PSE
unconditionally. This will cause all packets being flooded to PSE and may
cause PSE hang before entering linux.
This patch changes the connection between switch and PSE:
- Still initialize switch in probe stage, but disconnect it with PSE
- Connect switch with PSE on eth start
- Disconnect on eth stop
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Add rtl8169 NIC device ID and reorder the device ID.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
For RISC-V architeture, hardware maintain the dcache coherency.
Software do not flush the cache. So even cache-line size larger
than descriptor size, driver can work.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
While compiling rtl8169.c, There are many "make pointer from
integer without a cast" compile warnings. fix them with
adding cast.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Approved DT binding has the port mode register in the
"phys" property. Get it from there instead of the custom
"cpsw-phy-sel" property.
This will allow us to keep DT in sync with Linux.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Nishanth Menon <nm@ti.com>
The approved DT property for MAC efuse (ROM) address is
"ti,syscon-efuse".
Use that and drop custom property "mac_efuse".
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Nishanth Menon <nm@ti.com>
The binding represents the MDIO controller as a child device tree
node of the MAC device tree node.
The U-Boot driver mostly ignores that child device tree node and just
hardcodes the resources it uses to support both the MAC and MDIO in a
single driver.
However, some resources like pinctrl muxing states are thus ignored.
This has been a problem with some device trees that will put some
pinctrl states on the MDIO device tree node, like the SK-AM62 Device
Tree does.
Let's rework the driver a bit to create a dummy MDIO driver that we will
then get during our initialization to force the core to select the right
muxing.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Nishanth Menon <nm@ti.com>
The adin phy has extended registers that can be accessed using
adin_ext_read and adin_ext_write. These registers can be read directly
using the mdio command using readext and writext. For example:
=> mdio rx ethernet@428a0000 0xff23
Reading from bus ethernet@428a0000
PHY at address 0:
65315 - 0xe01
Signed-off-by: Nate Drude <nate.d@variscite.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Copy and tweak the required code from the linux kernel.
Only the KSZ9893 has been tested.
Signed-off-by: Karsten Wiese <karsten.wiese@protechna.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
If there is no incoming package than axiemac_recv will return -1 which
in turn leads to printing `eth_rx: recv() returned error -1` error
message in eth_rx function. But missing a package is not an fatal error,
so return -EAGAIN in that case would be more suitable.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20230719065337.69280-1-bigunclemax@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
As per spec MDC must not exceed 2.5MHz, read the pclk clock
from the device tree and update the MDC clock divisor.
GEM devices support larger clock divisors and have a different
range of divisors. Program the MDIO clock divisors based on
the clock rate of the pclk clock.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230619034922.24019-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The different CPSW sub-system Ethernet ports have different PHY mode
control registers. In order to allow the modes to get configured
independently only the register for the port in question must be
accessed, otherwise we would just be re-configuring the mode for port 1,
while leaving all others at their power-on defaults. Fix this issue by
adding a port-number based offset to the mode control base register
address based on the fact that the control registers for the different
ports are spaced exactly 0x4 bytes apart.
Fixes: 9d0dca1199 ("net: ethernet: ti: Introduce am654 gigabit eth switch subsystem driver")
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
The StarFive ETHQOS hardware has its own clock and reset,so add a
corresponding glue driver to configure them.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add a driver for the motorcomm yt8531 gigabit ethernet phy. We have
verified the driver on StarFive VisionFive2 board.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This patch targets the last remaining commands left to sync to their
latest form - mainly the mc_get_version() API.
Besides this, remove any macro which is now of no help.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sync the Data Path IO APIs to their latest form, this means the layout
of each command is created based on structures which clearly describe
the endianness of each field rather than some macros.
The command version is kept in place, meaning that the minimum MC
version accepted is not changed in any way.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sync the Data Path Soft Parser APIs to their latest form, this
means the layout of each command is created based on structures which
clearly describe the endianness of each field rather than some macros.
The command version is kept in place, meaning that the minimum MC
version accepted is not changed in any way.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sync the Data Path Network Interface APIs to their latest form, this
means the layout of each command is created based on structures which
clearly describe the endianness of each field rather than some macros.
The command version is kept in place, meaning that the minimum MC
version accepted is not changed in any way.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sync the Data Resource Container APIs to their latest form, this means
the layout of each command is created based on structures which clearly
describe the endianness of each field rather than some macros.
The command version is kept in place, meaning that the minimum MC
version accepted is not changed in any way.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sync the Data Path MAC APIs to their latest form, this means the
layout of each command is created based on structures which clearly
describe the endianness of each field rather than some macros.
The command version is kept in place, meaning that the minimum MC
version accepted is not changed in any way.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sync the Data Path Buffer Pool APIs to their latest form, this means the
layout of each command is created based on structures which clearly
describe the endianness of each field rather than some macros.
The command version is kept in place, meaning that the minimum MC
version accepted is not changed in any way.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There are multiple MC APIs which were added years ago but they are not
used at all in the u-boot source code. Remove all these APIs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The rtl8169 driver uses calls to dm_pci_bus_to_phys,
which are compiled under CONFIG_PCI.
Without CONFIG_PCI, this happens:
drivers/net/rtl8169.o: in function `rtl_recv_common':
drivers/net/rtl8169.c:555: undefined reference to `dm_pci_bus_to_phys'
It is only natural that this driver depends on CONFIG_PCI then.
The device does not work connected in another way anyway, and the driver
does not assume anything else at this moment.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Export the already existing DPNI and DPMAC counters through the newly
added callbacks.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The ldpaa_eth driver already had a DPMAC statistics dump, this patch
extends the list of stats and adds a bit more structure to the code.
For a bit more context, the DPAA2 u-boot software architecture uses a
default network interface object - a DPNI - which, at runtime, will get
connected to the currently used DPMAC object.
Each time the .stop() eth callback is called, the DPMAC is destroyed
thus any previous counters will get lost.
As a preparation for the next patches, we add a software kept set of
DPMAC counters which will get updated before each destroy operation
takes place.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The ldpaa_eth driver already had a DPNI statistics dump, this patch
extends the list of stats and adds a bit more structure to the code.
For a bit more context, the DPAA2 u-boot software architecture uses a
default network interface object - a DPNI - which, at runtime, will get
connected to the currently used DPMAC object.
Each time the .stop() eth callback is called, the DPNI is reset to its
original state, including its counters.
As a preparation for the next patches, we add a software kept set of
DPNI counters which will get updated before each reset operation takes
place.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In order to simplify code, dpni_statistics can be written as a union.
Using the raw accessors we can just loop through all the statistics from
a page without trying to access each an every one independently.
Make this change to a union.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In case RX error occurs, and the RD_RFE bit is set, the descriptor
is never returned back to the queue. Make sh_eth_recv_start return
zero length in this case so that the descriptor can be released
and pushed back to the list. Also return the more appropriate
-EAGAIN instead of -EINVAL if the descriptor is not ready yet.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
U-Boot writes to RX packets when constructing replies.
This can cause stale cached data to be written to RX
buffer while we're receiving a packet. This causes RX
packet corruption because we invalidate the cache right
before processing the packet. Invalidate packet buffer
cache when preparing RX descriptor as well. This seems
to fix RX packet drops with high RX traffic.
While at it flush the descriptors right before enabling
RX/TX in sh_eth_tx_desc_init/sh_eth_rx_desc_init callbacks
when they are ready instead of flushing after allocation.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The common code is now capable of handling reset GPIO associated
with PHY. Drop the local ad-hoc code in favor of common code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The common code is now capable of handling reset GPIO associated
with PHY. Drop the local ad-hoc code in favor of common code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
These two properties are used by various DTs in place of
current reset-assert-us/reset-deassert-us , handle both .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
In case a new PHY is created and DM_ETH_PHY is enabled, bind a
generic PHY driver from ETH_PHY uclass to the PHY to have a
matching DM representation of that PHY.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The phy_connect_dev() is legacy API, now that there are no users,
make it internal to phy.c and unpublish it from headers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Use new U-Boot phy_connect() API which also supports fixed PHYs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Use new U-Boot phy_connect() API which also supports fixed PHYs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Use new U-Boot phy_connect() API which also supports fixed PHYs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Use new U-Boot phy_connect() API which also supports fixed PHYs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Use new U-Boot phy_connect() API which also supports fixed PHYs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Use new U-Boot phy_connect() API which also supports fixed PHYs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The eth_phy_reset() is not used outside of this file, staticize it.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This platform is currently unmaintained and untested, so remove it.
Further, as it is the only TI816X SoC example, remove related files as
well.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Rockchip NFC driver update and dev addr pointer api update;
- use standard dr_mode for usb driver;
- rock pi boards dts update;
- Add rk3566 Anbernic boards;
- Misc fixes for drivers;
The fdt_addr_t and phys_addr_t size have been decoupled. A 32bit CPU
can expect 64-bit data from the device tree parser, so use
devfdt_get_addr_index_ptr instead of the devfdt_get_addr_index function
in the various files in the drivers directory that cast to a pointer.
As we are there also streamline the error response to -EINVAL on return.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fdt_addr_t and phys_addr_t size have been decoupled. A 32bit CPU
can expect 64-bit data from the device tree parser, so use
dev_read_addr_ptr instead of the dev_read_addr function in the
various files in the drivers directory that cast to a pointer.
As we are there also streamline the error response to -EINVAL on return.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fdt_addr_t and phys_addr_t size have been decoupled. A 32bit CPU
can expect 64-bit data from the device tree parser, so use
dev_read_addr_index_ptr instead of the dev_read_addr_index function
in the various files in the drivers directory that cast to a pointer.
As we are there also streamline the error response to -EINVAL on return.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Request the reset gpio of the rgmii-id phy as output to be consistent
with the eth-phy-uclass driver.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Add minimal support for 8125B version.
Changes are based on the Linux driver.
Tested on Radxa Rock 5B Rk3588 board.
Connection to a laptop worked fine in 100 Mbps mode.
1000 Mbps mode is not working at the moment.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
dp83867 driver only supports sgmii and not all the newer protocols.
Drop the usage of the generic phy_interface_is_sgmii function and just
matchup to the specific mode supported.
Reported-by: Tom Rini <trini@konsulko.com>
Suggested-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Suggested-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/all/b82ac325-4818-8e72-054b-640268dbf806@mailbox.org/
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
rtl8211e_startup() is an exact copy of genphy_startup(). Use that
instead of duplicating it.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Read the phy mode of the external phy from the device tree if available
and check that it is a RGMII variant.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Without that patch it lost track to the node to scan
speed and duplex.
Patch was created by Marek Vasut, just tested by me.
Signed-off-by: Elmar Psilog <epsi@gmx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
In the process of adopting CONFIG_DM_ETH on the DPAA2 based platforms,
interfaces which were previously defined as "xgmii" were transitioned to
be defined as "xfi" in the DTS.
See the commit below for reference:
commit 87274918f2 ("arm: dts: ls2088ardb: add DPMAC and PHY nodes")
Then Vladimir's commit replaced all occurrences of "xfi" with
"10gbase-r" in an effort to make U-Boot work with the same device tree
as Linux.
commit 77b11f7604 ("net: replace the "xfi" phy-mode with "10gbase-r"")
These changes to the phy_interface_t of an Ethernet port meant that the
mc_fixup_mac_addrs() function was no longer capable to properly fixup
the MAC addresses. The problem arises from the fact that the hardcoded
information about an interface (wriop_get_enet_if()) was no longer
matching any actual device.
For example, the function tried to search for "DPMAC1@xgmii1" by name
using eth_get_dev_by_name() when only "DPMAC1@10gbase-r" was available.
This function removes the need to rely on the hardcoded information by
iterating through all the UCLASS_ETH devices which are DPAA2 and request
a fixup for each of them.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Export the ldpaa_eth_get_dpmac_id() function so that it can be used from
other drivers, especially by fsl-mc which will need it the next patch.
Also, create a macro for the Ethernet ldpaa driver name and export it as
well.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Add a port_probe function to configure the phy. This leads to
earlier link negotiation so the port is more likely to be ready
when used.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
We don't do anything useful with the master dev, so remove the variable.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
packet tagging is not used for this driver so we do not need to
call dsa_set_tagging.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This patch adds Ethernet Switch support that found on R-Car S4
(r8a779f0) SoC. This is extracted from multiple patches from
downstream BSP, with additional rework of the network device
registration.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[Marek: Rework the driver to support all ports via subdrivers.
Split the driver up, add generic PHY framework support.
Generic code clean ups.]
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Now that all differences in functionality are covered by individual
flags, remove the enumeration of SoC variants.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
While R40 puts the EMAC syscon register at a different address from
other variants, the relevant portion of the register's layout is the
same. Factor out the register offset so the same code can be shared
by all variants. This matches what the Linux driver does.
This change provides two benefits beyond the simplification:
- R40 boards now respect the RX delays from the devicetree
- This resolves a warning on architectures where readl/writel
expect the address to have a pointer type, not phys_addr_t.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Describe this feature instead of using the SoC ID.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Describe this feature instead of using the SoC ID.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently, EMAC variants are distinguished by their identity, but this
gets unwieldy as more overlapping variants are added. Add a structure so
we can describe the individual feature differences between the variants.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add support for R-Car Gen4 SoCs and a matching DT compatible.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Drop SoC specific compatible, use RCAR_64 Kconfig symbol, update commit message]
Pull Marvell 10G PHY driver from Linux 6.1.y as of commit
d6d29292640d3 ("net: phy: marvell10g: select host interface configuration")
and heavily adapt to match U-Boot PHY framework. Support for
hwmon is removed as is much other functionality which could
not be tested, this results in much simpler driver which can
only bring the PHY up and set MAC type.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add phy_modify_mmd()/phy_modify_mmd_changed() from Linux 5.1.y as of commit
b8554d4f7288f ("net: phy: add register modifying helpers returning 1 on change")
This is used by the upcoming Marvell 10G PHY driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Import marvell_phy.h from Linux 5.14.y as of commit
a5de4be0aaaa6 ("net: phy: marvell10g: fix differentiation of 88X3310 from 88X3340")
and use it in marvell PHY driver instead of current ad-hoc macros.
Two of the PHY IDs are unknown to Linux, 88E1149S and 88E1680, for
those two, only sync the length of the hexadecimal number to 8 digits.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Synchronize PHY interface modes with Linux next 6.2.y commit:
0194b64578e90 ("net: phy: improve phy_read_poll_timeout")
Retain LX2160A/LX2162A PHY modes as those are not yet supported
by the Linux kernel, but isolate those with ifdeffery.
Isolate NCSI which are also not supported by Linux kernel. Note
that the ifdeffery cannot be avoided with IS_ENABLED() here due
to compilation of the entire conditional, which would fail in
case NCSI symbols are not available.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Replace PHY_INTERFACE_MODE_SFI with PHY_INTERFACE_MODE_5GBASER,
PHY_INTERFACE_MODE_10GBASER and PHY_INTERFACE_MODE_XAUI to match
Linux PHY interface modes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This mode does not seem to be well defined and used anywhere, remove support for it.
Based on discussion:
- 1000baseX does c37 AN of duplex+pause
- SGMII does AN of duplex+pause+speed, at lower speed bytes are repeated 10x/100x
- 2500baseX does not do AN, or does very different c73 AN
- SGMII 2500 behavior is unclear
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The phy_init() is now used only to perform manual relocation of PHY
driver callbacks. Wrap it in ifdeffery and only call it on systems
which still require manual relocation, i.e. m68k .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Wrap phy_drv_reloc() back into phy_init() to reduce ifdeffery,
since phy_drv_reloc() is now called only from one call site.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
This function is no longer used, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
The static phy_drivers list is superseded by linker list of struct phy_drivers
now that all drivers have been converted to the later. Drop the phy_drivers
list as well as list_head from struct phy_driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
This particular PHY driver is slightly more spread out across additional
source files. Since the phy_register() calls are no longer necessary, all
the registration calls across those source files is dropped. Furthermore,
the Makefile can now be updated to only compile generic TI PHY support if
matching Kconfig symbol is enabled and the ifdeffery in the generic TI PHY
driver can be dropped.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Introduce U_BOOT_PHY_DRIVER() macro which is used to add struct phy_driver
into a new linker list section containing all compiled in struct phy_driver
drivers. This is so far empty until PHY drivers are converted over to this
macro.
Iterate over both drivers registered using soon to be legacy phy_register()
as well as drivers in the new linker list when looking up a suitable PHY
driver. This way, PHY drivers can be converted over to the new macro one
driver at a time.
The relocation of callbacks for linker list based drivers now happens in
phy_init() call as the drivers are available at that point in time, and
phy_register() is not called for those drivers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Create separate function to implement manual relocation of PHY driver
functions and make use of that function. This is a preparatory patch
for introduction of PHY driver definition using linker lists.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
These struct phy_driver ... instances are local to this source code
file, staticize them. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
These struct phy_driver ... instances are local to this source code
file, staticize them. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
These struct phy_driver ... instances are local to this source code
file, staticize them. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
These struct phy_driver ... instances are local to this source code
file, staticize them. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Implement common board_interface_eth_init() and call it from the FEC
driver to configure IOMUXC GPR[1] register according to the PHY mode
obtained from DT. This supports all three interface modes supported by
the i.MX8M Mini/Nano/Plus FEC and supersedes the current board-side
configuration of the same IOMUX GPR[1] duplicated in the board files.
Signed-off-by: Marek Vasut <marex@denx.de>
The FEC ref clock frequency on i.MX8M Mini/Nano/Plus was so far configured
via ad-hoc board code. Replace that with DM clock clk_set_rate() instead.
This way, the driver claims all its required clock and sets the ref clock
rate, without any need of architecture specific register fiddling.
Signed-off-by: Marek Vasut <marex@denx.de>
Implement common board_interface_eth_init() and call it from the DWMAC
driver to configure IOMUXC GPR[1] register according to the PHY mode
obtained from DT. This supports all three interface modes supported by
the i.MX8M Plus DWMAC and supersedes current board-side configuration
of the same IOMUX GPR[1] duplicated in the board files.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
With DM clock support in place, it is easy to add RMII support into the
MAC driver. The RMII cannot operate at 1000 Mbps and at 100 and 10 Mbps
the clock frequency is 50 MHz and 5 MHz instead of 25 MHz and 2.5 MHz.
The board DT requires the following adjustments to EQoS node:
phy-mode = "rmii";
assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_266M>,
<&clk IMX8MP_SYS_PLL2_100M>,
<&clk IMX8MP_SYS_PLL2_50M>;
assigned-clock-rates = <0>, <100000000>, <50000000>;
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
The DWMAC clock in i.MX8M Plus were so far configured via ad-hoc
architecture code. Replace that with DM clock instead. This way,
the driver claims all its required clock, enables and disables
them, and even gets the CSR clock rate and sets the TX clock rate,
without any need of architecture specific register fiddling. Drop
the architecture specific code while at it too.
The adjustment here is modeled after STM32MP15xx clock handling
in this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver currently only waits for DMA_MODE SWR bit to clear itself.
This is insufficient e.g. on i.MX8M Plus, where the MAC must be reset
before IOMUX GPR[1] content is latched into the MAC and used. Without
the proper reset, the i.MX8M Plus MAC variant does not take the value
in IOMUX GPR[1] into account, which makes it impossible e.g. to switch
interface mode from RGMII to any other.
Since proper reset is desired in general to put the block into defined
state, always assert the DMA_MODE SWR bit before waiting for the bit
to clear itself.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
This function is only used within the driver, staticize it.
Fixes: 149e80f74b ("net: dwc_eth_qos: public some functions")
Signed-off-by: Marek Vasut <marex@denx.de>
The dm_gpio_free() is never called, because for stm32, the phy_reset_gpio
pointer is never valid. This is because only tegra186 ever claims the
phy_reset_gpio, all other platforms use the PHY framework to reset the
PHY instead. Drop the dm_gpio_free() and dm_gpio_is_valid().
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
The return is never triggered due to the goto just above it.
Drop it. No functional change.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Move the board_interface_eth_init() into common ethernet uclass code,
since this function could be shared by multiple drivers.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Calling old U-Boot API doesn't allow to use fixed PHY.
Searching by mask is the part of new function, after
scanning FDT for a fixed PHY definition
Fixes: e821a7bdb1 ("net: ravb: Detect PHY correctly")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Mikhail Lappo <mikhail.lappo@esrlabs.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
[Hai Pham: Drop phy_connect_dev since it's called in phy_connect]
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Use mask -1 instead of 0 to reinstate the search behavior
over all PHY addresses. Add Fixes tag, sort the tag list.]
There are missing Kconfig dependencies in the code which is using
firmware interface.
The commit 71efd45a5f ("arm64: zynqmp: Change firmware dependency")
add option to also disable ZYNQMP_FIRMWARE. But not all Kconfig
dependencies were properly described and also sdhci and gem drivers
didn't protect the code properly.
So, add the missing ZYNQMP_FIRMWARE dependencies.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230201095553.11219-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add a new SPL_PHY_ATHEROS to avoid a build error on am335x_evm with split
config.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This converts 3 usages of this option to the non-SPL form, since there is
no SPL_PHY_FIXED defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
Register mii_bus with read and write callbacks to allow the 'mii'
command to work. Use a timeout of 10 ms to wait for the R/W
operations to complete.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Tested-by: Rick Chen <rick@andestech.com>
Replace 'phys_addr_t iobase' with 'struct ftmac100 *ftmac100' in
struct ftmac100_data. It allows to remove casting in a number of places.
Since priv->iobase is phys_addr_t, use phys_to_virt() to make
a pointer from it.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
So it will be named similarly to the related ftgmac100 driver.
The old name 'nds32_mac' is not referred to anywhere in U-Boot.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The Qualcom ETHQOS hardware supports an RGMII macro which needs to be
configured according to following link speeds:
- SPEED_1000
- SPEED_100
- SPEED_10
So add a corresponding glue driver to configure RGMII macro.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The GMAC controller on QCS404 SoC (support added by upcoming patch) fails
to work with maximum tx/rx_fifo_sz supported by the hardware (16K). So
allow platforms to override FIFO size using corresponding DT node
properties.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This converts 6 usages of this option to the non-SPL form, since there is
no SPL_IMX_MODULE_FUSE defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
Prevent a NULL pointer dereference in the probe path by checking the
return valud of dev_read_addr_ptr() against NULL.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Remove the instances in which we have multiple blank lines.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
There were some cases in which the function parameters were not aligned
to the open paranthesis. Fix those instances.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Remove all the explicit casts from the void* returned by calloc.
With this we also improve a bit the length of those lines and there is
no need to split the assignment.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The fsl-mc driver printed debug information which used the 0x prefix for
decimal values. This only confuses anyone looking through the log.
Because of this, just remove the prefix and use the "DPXY.<id>" notation
which is the standard one for the DPAA2 objects.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The break statement is just after a goto statement, thus it will not get
executed. Just remove it.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The cur_ptr variable is set to the start of the log buffer but then it's
not used. Just remove the assignment altogether.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add a DSA driver for the MV88E6xxx compatible Ethernet switches.
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add support for DM_MDIO by registering a UCLASS_MDIO driver and
attempting to use it. This is necessary if wanting to use a DSA
driver for example hanging off of the FEC MAC.
Care is taken to fallback to non DM_MDIO mii bus as several boards define
DM_MDIO without having the proper device-tree configuration necessary
such as an mdio subnode, a phy-mode prop, and either a valid phy-handle
prop or fixed-phy subnode which will cause dm_eth_phy_connect() to fail.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Remove the unnecessary xmit and recv functions.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The current set of U-Boot upstream R-Car Gen3 DTs all contain generic
"renesas,etheravb-rcar-gen3" compatible strings, drop the SoC specific
compatible string support from U-Boot to reduce size and duplication.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
makefile:
- Add multi_dtb_fit dependency
clk:
- Handle error cases
microblaze:
- Disable falcon mode and cleanup code around
xilinx:
- Enable regular expression matching in board_fit_config_name_match()
- Fix FRU handling for 0xC1 format
- Fix Xilinx legacy format eeprom parsing
zynqmp:
- Some DT updates/cleanups
- Fix IDcode for xck24
- Remove empty mini config files
- Add support for k24
versal:
- Remove empty mini config files
versal_net:
- Setup timer when runs in EL3
- Build u-boot.elf for mini configurations
zynq-gem:
- Add support for new compatible strings
- Remove support for Avnet Ultrazedev SOM
- Handle SGMII with PCS phy
spi:
- Add support for gigadevice parts
misc:
- Remove CONFIG_TARGET_VENUS ifdef
- Add missing headers to remove sparse warnings
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCY9PmzwAKCRDKSWXLKUoM
IYWxAJwNgiXtFT17pBy+1M0JvSWgyvWF3QCfTQG2Krnw0+d65PF5A7UFTDL7SZM=
=cMrc
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx chnages for v2023.04-rc1
makefile:
- Add multi_dtb_fit dependency
clk:
- Handle error cases
microblaze:
- Disable falcon mode and cleanup code around
xilinx:
- Enable regular expression matching in board_fit_config_name_match()
- Fix FRU handling for 0xC1 format
- Fix Xilinx legacy format eeprom parsing
zynqmp:
- Some DT updates/cleanups
- Fix IDcode for xck24
- Remove empty mini config files
- Add support for k24
versal:
- Remove empty mini config files
versal_net:
- Setup timer when runs in EL3
- Build u-boot.elf for mini configurations
zynq-gem:
- Add support for new compatible strings
- Remove support for Avnet Ultrazedev SOM
- Handle SGMII with PCS phy
spi:
- Add support for gigadevice parts
misc:
- Remove CONFIG_TARGET_VENUS ifdef
- Add missing headers to remove sparse warnings
