This was applied prematurely by me as I missed the feedback provided at
the time.
This reverts commit c9c8df2c37.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add the driver for the Airoha EN8811H 2.5 Gigabit PHY. The PHY supports
100/1000/2500 Mbps with auto negotiation only.
The driver uses two firmware files, for which updated versions are added to
linux-firmware already.
Based on the Linux upstream 8811 driver code(air_en8811h.c),
I have modified the relevant process to align with the U-Boot boot sequence.
and have validated this on Banana Pi BPI-R3 Mini.
The MD32 FW is currently stored in eMMC partition 1 on Banana Pi BPI-R3 Mini,
and it is loaded from there.
Signed-off-by: Lucien.Jheng <lucienzx159@gmail.com>
We can call phy_modify_mmd() instead of manually calling drv->readext()
and drv->writeext().
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Various signal skew values may be set in the device tree for the ksz9131
Ethernet PHY. For example, the RZ/G2L board requires non-default values
for rxc-skew-psec & txc-skew-psec.
This is based on the ksz9131 phy driver in Linux v6.11.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Micrel KSZ9131 PHY LED behavior is not correct when configured in
Individual Mode, LED1 (Activity LED) is in the ON state when there is
no-link.
Workaround this by setting bit 9 of register 0x1e after verifying that
the LED configuration is Individual Mode.
This issue is described in KSZ9131RNX Silicon Errata DS80000693B [*]
and according to that it will not be corrected in a future silicon
revision.
[*] https://ww1.microchip.com/downloads/en/DeviceDoc/KSZ9131RNX-Silicon-Errata-and-Data-Sheet-Clarification-80000863B.pdf
Based on commit 0316c7e66bbd in the Linux kernel.
Tested-by: Quentin Schulz <quentin.schulz@cherry.de> # RK3588 Tiger
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
These functions are no longer necessary, remove them.
The struct bb_miiphy_bus is no longer necessary either,
remove it as well.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Access to MDIO bus private data can be provided by both
struct mii_dev .priv member and struct bb_miiphy_bus .priv
member, use the former directly and remove .priv from the
later. Drop unused bb_miiphy_getbus(). This removes any
dependency on struct bb_miiphy_bus from the miiphybb code,
except for helper functions which will be removed later.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
The access to struct bb_miiphy_bus_ops via ops pointer in
struct bb_miiphy_bus is not necessary with wrappers added
in previous patch. Pass the ops pointer directly to both
bb_miiphy_read() and bb_miiphy_write() functions.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Move miiphybb operations into separate struct bb_miiphy_bus_ops
structure, add pointer to struct bb_miiphy_bus_ops into the base
struct bb_miiphy_bus and access the ops through this pointer in
miiphybb generic code. The variable reshuffling in miiphybb.c
cannot be easily avoided.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Replace the name based look up in bb_miiphy_getbus() with trivial
container_of() call. This works because the struct bb_miiphy_bus
always embeds the matching struct mii_dev . This also makes the
code much simpler and more efficient.
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Introduce bb_miiphy_alloc()/bb_miiphy_free() wrappers to allocate and free
struct bb_miiphy_bus. Make struct bb_miiphy_bus wrap struct mii_dev, which
will become useful later in bb_miiphy_bus accessors, which would be able
to access struct bb_miiphy_bus using container_of, even if the PHY stack
only passes in the inner struct mii_dev .
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The .init callback is not called by any function, drop it.
There are no more users of the init callback, drop the entire
mechanism.
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Update the debug() print, use __func__ to always print matching
function name, and also print bus name in case there are multiple
busses.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Replace ifdeffery with plain debug() function call. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
The TI DP83822 does have support for configurable RGMII RX/TX clock
shift, add support for parsing DT properties which describe the RX/TX
clock shift configuration and configuration of the matching bits in
RCSR register.
The shift is only configurable on DP83822, the other PHYs supported
by this PHY driver, namely DP83825/DP83826 variants, do not implement
this functionality and the RCSR bits used to configure the clock shift
are missing from those PHYs.
The shift is configurable separately for RX and TX path. Each path can
either enable the shift or disable the shift using single bit. In case
the shift is disabled, a delay of 0ns is added to the path, otherwise
a delay of 3.5ns is added to the path.
Note that the two RCSR bits 11 and 12 have inverted logic, RCSR bit 12
enables RX internal shift when SET, while RCSR bit 11 enables TX shift
when UNSET.
Signed-off-by: Marek Vasut <marex@denx.de>
It seems that every remaining system which enables BITBANGMII also
enables BITBANGMII_MULTI . Remove the BITBANGMII_MULTI symbol and
assume it is always enabled. This allows removal of a bit of legacy
code. No functional change intended.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
This reverts commit 431be621c6.
Section 3.3 of Reduced Gigabit Media Independent Interface (RGMII)
Version 2.0 (4/1/2002) details that a PHYs using a ~2ns internal delay
are referred to as RGMII-ID. This internal delay is optional.
Page 147-148 of the Marvell Doc. No. MV-S107146-U0 Rev. F details
timings of the RX/TX delays. We see that with the TX/RX_CLK delay
enabled, our RX/TX_CTL signal is shifted w.r.t CLK to reflect the delay
added.
In 431be62 there is no timing difference between RGMII and RGMII-ID, and
so programmers wanting to explicitly set their PHY to RGMII will find
that delay added anyway. This could throw off timing if that internal
delay is undesired.
We should be handling all 4 possible RGMII cases of PHY_INTERFACE_MODE:
RGMII, RGMII_ID, RGMII_TXID, and RGMII_RXID. Reverting 431be62
implements this.
See also m88e1111_config_init_rgmii_delays in the equivalent driver in
Linux (drivers/net/phy/marvell.c), which does not set these delays in
RGMII mode.
68e6eca was tested out on an 88E1512 PHY in RGMII-ID mode. This
reversion has been tested by myself on an 88E1518 in RGMII-ID mode. This
patch affects boards using this driver in "rgmii" mode, as the internal
delay will no longer be enabled. Namely kikwood-nsa310s.
Signed-off-by: Rufus Segar <rhs@riseup.net>
Add a driver for the motorcomm YT8821 2.5G ethernet phy which works in
2500base-x mode.
Verify the driver on BPI-R3(with MediaTek MT7986(Filogic 830) SoC) evb.
Signed-off-by: Frank Sae <Frank.Sae@motor-comm.com>
Prepare the introduction of the lwIP (lightweight IP) TCP/IP stack by
adding a new net/lwip/ directory and the NET_LWIP symbol. Network
support is either NO_NET, NET (legacy stack) or NET_LWIP. Subsequent
commits will introduce the lwIP code, re-work the NETDEVICE integration
and port some of the NET commands and features to lwIP.
SPL_NET cannot be enabled when NET_LWIP=y. SPL_NET pulls some symbols
that are part of NET (such as arp_init(), arp_timeout_check(),
arp_receive(), net_arp_wait_packet_ip()). lwIP support in SPL may be
added later.
Similarly, DFU_TFTP and FASTBOOT are not compatible with NET_LWIP
because of dependencies on net_loop(), tftp_timeout_ms,
tftp_timeout_count_max and other NET things. Let's add a dependency on
!NET_LWIP for now.
SANDBOX can select NET_LWIP but doing so will currently disable the eth
dm tests as well as the wget tests which have strong dependencies on the
NET code.
Other adjustments to Kconfig files are made to fix "unmet direct
dependencies detected" for USB_FUNCTION_SDP and CMD_FASTBOOT when
the default networking stack is set to NET_LWIP ("default NET_LWIP"
instead of "default NET" in Kconfig).
The networking stack is now a choice between NO_NET,
NET and NET_LWIP. Therefore '# CONFIG_NET is not set' should be
'CONFIG_NO_NET=y'. Adjust the defconfigs accordingly.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
PHY_NCSI enables drivers/net/phy/ncsi.c which calls net_loop() and
net_set_timeout_handler(). That's the legacy NET stack (as opposed to
NET_LWIP). Therefore add the dependency to Kconfig.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Switch PHY_ANEG_TIMEOUT to CONFIG_PHY_ANEG_TIMEOUT Kconfig symbol.
This removes one more configuration headers option finalizes its
Kconfig symbol conversion. No functional change expected.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Let users configure default auto-negotiation timeout via Kconfig
instead of specifying it in board configuration headers. This is
the first step toward converting this to Kconfig fully, so far the
legacy PHY_ANEG_TIMEOUT in configuration headers takes precedence.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d, reversing
changes made to 2ee6f3a5f7.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Pull the PHY GPIO reset code into separate function, since
this is and will be reused multiple times. Set up default
reset assert and deassert timing to generous 20ms and 1ms
for maximum compatibility in case those DT properties are
missing.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
From the ethernet header is not on aligned, because the length
of the ethernet header is 14 bytes.
Therefore, unaligned access must be done here.
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
There is no need to perform the endian twice here.
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
As with fixed-link phy device, the NC-SI phy devive does not
require an mdio bus. So, a condition is added to check the
NC-SI phy id to avoid accessing the bus pointer that is NULL.
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
Booting R-Car Gen3 arm64 U-Boot with CONFIG_UBSAN=y resulted in:
=====================================================================
UBSAN: Undefined behaviour in drivers/net/phy/phy.c:728:19
left shift of 1 by 31 places cannot be represented in type 'int'
=====================================================================
Fix it by appending the UL suffix to the numeric literal. While at it,
convert the type of "addr" variable from signed to unsigned, to protect
against shifting the numeric literal by a negative value (which would
lead to yet another undefined behavior).
Fixes: 1adb406b01 ("phy: add phy_find_by_mask/phy_connect_dev")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
* Using U-suffix for integer is sufficient.
* ffs() of non-zero value cannot be 0. But addr being unsigned is
* preferable.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Configure LEDs on BCM54210E so they would blink on activity
and indicate link speed. Without this the LEDs are always on
if cable is plugged in.
Signed-off-by: Marek Vasut <marex@denx.de>
The issue occurs the UAF (use-after-free) to cause double free
when do the realloc function for the pointers during the
reinitialization NC-SI process, and it will cause the memory
management occurs error.
So, nullify these pointers after free.
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
In case the PHY is fully described in DT, use PHY MDIO address
from DT directly instead of always using auto-detection. This
also fixes the behavior of 'mdio list' in such DT setup, which
now prints the PHY connected to the MAC correctly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Rename nxp_c45_tja11xx structure to nxp_c45_tja1103. The driver will
support more PHYs and nxp_c45_tja11xx is too generic.
Signed-off-by: "Radu Pirea (NXP OSS)" <radu-nicolae.pirea@oss.nxp.com>
Read PHY speed from hardware instead of assuming 100Mbps by default.
The TJA1103 works only at 100Mbps, but the driver will support more PHYs.
Signed-off-by: "Radu Pirea (NXP OSS)" <radu-nicolae.pirea@oss.nxp.com>
Use a local definition for the PHY features. PHY_100BT1_FEATURES are
not defined using the 100BaseT1 bit, so keep this workaround in the driver.
Signed-off-by: "Radu Pirea (NXP OSS)" <radu-nicolae.pirea@oss.nxp.com>
This ports the pad drive strength register configuration which can be
already found in the Linux driver for this PHY.
Signed-off-by: Lukasz Tekieli <tekieli.lukasz@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Setting the clock delay from the device tree settings
rx-internal-delay-ps and tx-internal-delay-ps was broken:
- The expected value in the device tree is suppose to be a
delay in picoseconds, but the driver only allowed an array index.
- Driver converted this array index to the actual delay in
picoseconds and tried to apply this in the device register. This
however is not a valid register value. The actual logic here was
reversed, it converted an register representation of the delay to
the device tree delay in picoseconds.
Only when the internal delays were NOT configured in the device tree
and they default value of 7 (=2000ps) was used, a valid value was
loaded in the register.
Signed-off-by: Frank de Brabander <debrabander@gmail.com>
As the xlnx,phy-type device tree property is deprecated and phy-mode
is being used, so removing the code references of xlnx,phy-type.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231010030436.11854-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
This old patch was marked as deferred. Bring it back to life, to continue
towards the removal of common.h
Move this out of the common header and include it only where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Current code expects bridge phy address at 0 which is not correct
expectation because bridge phy address is configurable.
That's why update the code to read reg property to figure it out
where bridge is and use it in phy creation code.
Signed-off-by: Tejas Bhumkar <tejas.arvind.bhumkar@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20230915045043.4167628-1-tejas.arvind.bhumkar@amd.com
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
