The set_dfu_alt_info() function calls the ALLOC_CACHE_ALIGN_BUFFER()
macro to declare a `buf' variable pointer into an array allocated on the
stack. It then calls the memset() function to clear the useable portion
of the array using the idiomatic expression `sizeof(buf)'.
While this would indeed work fine for an array, in the present case we
end up clearing only the size of a pointer.
Fix this by specifying the explicit size `DFU_ALT_BUF_LEN' instead.
Fixes: 064c8978b4 ("arm64: versal: Enable capsule update (SD)")
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Michal Simek <michal.simek@amd.com>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Padmarao Begari <padmarao.begari@amd.com>
Link: https://lore.kernel.org/r/20250407170529.893307-4-vincent.stehle@arm.com
Added extended support for retrieving the PMC muti boot mode
register via the firmware interface, which is preferred when
U-Boot runs in EL2 and cannot directly access PMC registers
via raw reads. Ideally, all secure registers should be accessed
via xilinx_pm_request(). Introduced the secure
zynqmp_pm_get_pmc_multi_boot_reg() call, which uses
xilinx_pm_request() to read the PMC multi boot mode register.
BootROM increments the MultiBoot register (PMC_MULTI_BOOT) read
address offset by 32 KB and retries. For SD and eMMC boot modes,
it can search up to 8191 FAT files for the identification string.
A 13-bit mask (0x1FFF) is applied to PMC_MULTI_BOOT_MASK to obtain
the correct values in BootROM.
Signed-off-by: Prasad Kummari <prasad.kummari@amd.com>
Link: https://lore.kernel.org/r/20250305134845.3182193-1-prasad.kummari@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Added extended support for retrieving the boot mode register
via the firmware interface, which is preferred when U-Boot
runs in EL2 and cannot directly access CRP registers via raw
reads. Ideally, all secure registers should be accessed via
xilinx_pm_request(). Introduced the secure zynqmp_pm_get_bootmode_reg()
call, which uses xilinx_pm_request() to read the boot mode register.
When CONFIG_ZYNQMP_FIRMWARE is enabled, the secure
zynqmp_pm_get_bootmode_reg() call is used; otherwise,
direct raw reads are performed in the case of mini U-Boot.
Signed-off-by: Prasad Kummari <prasad.kummari@amd.com>
Link: https://lore.kernel.org/r/20250219115301.3661036-1-prasad.kummari@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Now that capsule update sets the dfu_alt_info environment variable
explicitly, there is no need to support it in the set_dfu_alt_info()
function. Decouple SET_DFU_ALT_INFO from EFI_CAPSULE_FIRMWARE_FIT and
EFI_CAPSULE_FIRMWARE_RAW. For many boards, this was the only use of
set_dfu_alt_info() so remove the function entirely.
Fixes: a9e6f01a94 ("efi: Define set_dfu_alt_info() for boards with UEFI capsule update enabled")
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> # for board/libre-computer/*
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de> # for
Directly fill update_info.dfu_string to prepare platforms to switch
from using dfu_alt_info variable to dfu_string which contains description
for capsule update when switch is done.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The main reason for this change is that upstream QEMU has no multiboot
register implemented that's why access to it fails which ends up in CI
failure for our target.
That's why in JTAG bootmode returns 0 which is correct behaviour because
multiboot register is not used in this mode and value should be ignored and
as a side effect it is also fixing CI/Qemu issue.
Also move versal_get_bootmode() to avoid function declaration.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/484b9cafc45e72308a1a29a3ab772020f96784cc.1736155238.git.michal.simek@amd.com
SOC can boot out of the device which is not accessible from APU and running
this is detected as a warning, as the device is not accessible.For example
getting below warning when the boot mode is OSPI and OSPI is not enabled in
device tree.
Invalid bus 0 (err=-19)
Failed to initialize SPI flash at 0:0 (error -19)
Ignoring the prioritization of the boot device which driver is not enabled
and continue with the default boot_targets. Recommendation is to use custom
boot_targets via environment file as is done for example for Kria via
zynqmp_kria.env file.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/8b7cca5c7b84cb4854104e0c48f8aa63c4ec5ace.1715322156.git.michal.simek@amd.com
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d, reversing
changes made to 2ee6f3a5f7.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Private function for finding out location of environment is not working
when ENV_IS_NOWHERE is disabled.
The reason is that current fallback is ENVL_UNKNOWN when
CONFIG_ENV_IS_NOWHERE is not enabled. The code could be updated like this
- return ENVL_NOWHERE;
+ if (IS_ENABLED(CONFIG_ENV_IS_NOWHERE))
+ return ENVL_NOWHERE;
+ return ENVL_UNKNOWN;
But then boot is still not working because ENVL_UNKNOWN has no driver and
env_init() returns -ENODEV. That's why it is better not to define board
specific env_get_location() because then weak env_get_location() is used
which is going over env_locations[] and returning locations which are
actually enabled in u-boot instance.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/830b9c93d30688cfa8a5cbb0388e79deb7731f29.1711107795.git.michal.simek@amd.com
The SelectMAP configuration interface provides an 8-bit,
16-bit or 32-bit bidirectional data bus interface to the Versal FPGA
configuration logic that can be used for both configuration and readback.
A connected microcontoller to the SelectMAP interface can load boot
image with bitstream, TF-A (ARM Trusted Firmware) and U-Boot.
This commit adds the missing identification of the SelectMAP mode.
Signed-off-by: Polak, Leszek <LPolak@arri.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Michal Simek <michal.simek@amd.com>
Cc: Stefan Roese <sr@denx.de>
Link: https://lore.kernel.org/r/DU0PR07MB8419F7765892CDBCE7D559C5C8CFA@DU0PR07MB8419.eurprd07.prod.outlook.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
SOC can boot in the device which is not accessible from APU and running
this is detected as error which ends up in stopping boot process.
Boot mode detection and logic around is present to setup priority on boot
devices that SOC boot device is likely also used for booting OS.
Change logic to detect this case with showing message about it but don't fail
in boot process and don't prioritize boot device in this case.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20230904032035.11926-3-venkatesh.abbarapu@amd.com
This converts 4 usages of this option to the non-SPL form, since there is
no SPL_ENV_VARS_UBOOT_RUNTIME_CONFIG defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
The commit ce39ee28ec ("zynqmp: Do not place u-boot to reserved memory
location") adds functionality for ZynqMP to read reserved memory node and
do not place U-Boot to reserved location. This functionality is generic
across all Xilinx SOCs that's why move it to common location to be used by
all Xilinx SOCs.
On zynq platform this is also fixing issue where U-Boot was placed to
locating which was reserved already which ends up with error message
"ERROR: reserving fdt memory region failed (addr=30000000 size=10000000
flags=4)" which is shown when bdinfo is called.
Tested on vck190, zcu102, zc706 and kc705 to cover all platforms.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/b0817807912f7c7af6a8e1cf9ee04e5ab5de5f6a.1661430188.git.michal.simek@amd.com
Store a set of supported bitstream types in xilinx_desc structure.
It will be used to determine whether an FPGA image is able to be
loaded with a given driver.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Tested-by: Ricardo Salveti <ricardo@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-4-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support to switch to EL1 and load an EL1 app from U-Boot which is
executing at EL2 or EL3 in aarch64 mode.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220506055345.1921-1-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
board_get_usable_ram_top() was designed for getting the top most location
for U-Boot allocation that's why function itself supports via total_size
parameter to find out where the right location for U-Boot is.
But function itself is also reused by different (EFI) which is passing
total_size as 0 to find out where the usable ram top is. For this case
doesn't make sense (a waste time) to call any lmb functions.
That's why simply return gd->ram_top.
And gd->ram_top is filled already based on previous call for U-Boot iself.
The same solution is also used by stm32mp by commit 92b611e8b0 ("stm32mp:
correctly handle board_get_usable_ram_top(0)") and commit c8510e397f
("stm32mp: Fix board_get_usable_ram_top()").
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/44470619e74f3e480b70deac24578e3e0d5c907e.1651225945.git.michal.simek@amd.com
Since versal has CONFIG_COUNTER_FREQUENCY, so use it. And
COUNTER_FREQUENCY will be dropped.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Versal can also have reserved space in DT which u-boot has to avoid to
placing self to that location. The same change was done in ZynqMP by commit
ce39ee28ec ("zynqmp: Do not place u-boot to reserved memory location")
and also for microblaze by commit d7b5cc89d3 ("microblaze: Do not place
u-boot to reserved memory location").
The patch was tested by adding reserved-memory node to DT and check via
bdinfo back.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/15426fa6d64835dd23c5c8c12bbfc97306fb6098.1647527129.git.michal.simek@xilinx.com
The system fails to boot without any environment location, so return
ENVL_NOWHERE when there's nowhere to store the environment instead
of ENVL_UNKNOWN.
The same change was also done by commit 50918d0df5 ("xilinx: Return
ENVL_NOWHERE instead of ENVL_UNKNOWN") for zynq and zynqmp.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/e4ed36408f10159677ed8060bfd5289f3e0691fa.1637752614.git.michal.simek@xilinx.com
Change "dfu_usb" to "usb_dfu" for better representation and change
required macros. Add 60s timeout of dfu-utils to start transaction.
Add support for usb thor to distro boot. Remove DFU_ALT_INFO_RAM
as we use bootcmd_usb_dfu instead of dfu_ram.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable saving variables to MMC(FAT) and SPI based on primary
bootmode. If bootmode is JTAG, dont save env anywhere(NOWHERE).
Enable ENV_FAT_DEVICE_AND_PART="0:auto" for Versal platforms as well.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Historically, the reset_cpu() function had an `addr` parameter which was
meant to pass in an address of the reset vector location, where the CPU
should reset to. This feature is no longer used anywhere in U-Boot as
all reset_cpu() implementations now ignore the passed value. Generic
code has been added which always calls reset_cpu() with `0` which means
this feature can no longer be used easily anyway.
Over time, many implementations seem to have "misunderstood" the
existence of this parameter as a way to customize/parameterize the reset
(e.g. COLD vs WARM resets). As this is not properly supported, the
code will almost always not do what it is intended to (because all
call-sites just call reset_cpu() with 0).
To avoid confusion and to clean up the codebase from unused left-overs
of the past, remove the `addr` parameter entirely. Code which intends
to support different kinds of resets should be rewritten as a sysreset
driver instead.
This transformation was done with the following coccinelle patch:
@@
expression argvalue;
@@
- reset_cpu(argvalue)
+ reset_cpu()
@@
identifier argname;
type argtype;
@@
- reset_cpu(argtype argname)
+ reset_cpu(void)
{ ... }
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
At present various drivers etc. access the device's 'seq' member directly.
This makes it harder to change the meaning of that member. Change access
to go through a function instead.
The drivers/i2c/lpc32xx_i2c.c file is left unchanged for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Starts to use new way how eeproms should be referenced.
Reference is done via nvmem alias nodes. When this new way is specified
code itself read the eeprom and decode xilinx legacy format and fill struct
xilinx_board_description. Then based on information present there board_*
variables are setup.
If variables are saved and content can't be changed information is just
shown on console.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Start to use ENV_VARS_UBOOT_RUNTIME_CONFIG to enable/disable updating
variables with run time information.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Find and use the lowest memory for Versal to make sure that we keep u-boot
as low as possible and never use memory above u-boot's maximum VA mapping.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Create special function for reading bootmode on Versal and ZynqMP.
Zynq is using specific function (without mask) already.
Future patches will be calling this function from different location too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Currently "script_offset_f" env variable is hardcoded, this variable
specifies from which offset of the flash boot.scr should be read/write.
As flashes are of different sizes having a fixed offset makes it
difficult to load other images into the flash which may overwrite the
boot script or cannot utilize the full memory. This current fix
creates a new config "CONFIG_BOOT_SCRIPT_OFFSET" which holds the
offset address, overwrites the "script_offset_f" variable.
Also removed existing variable with default values, as the default
values are held by CONFIG_BOOT_SCRIPT_OFFSET
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Emmc boot devcie is mounted to sdhci@f1050000 controller on versal, while
in emmc boot mode, boot tragets are set to mmc0. So removed mmc0 and using
the dev seq number from the sdhci@f1050000 controller.
Dev seq number is setup based on DT aliases that's why needs to be setup at
run time.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
A number of board function belong in init.h with the others. Move them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function belongs in time.h so move it over and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
