for rk3308, all defconfigs have CONFIG_OF_LIBFDT_OVERLAY=y, so enable it
by default.
for rk3328, any defconfig doesn't have it. but there is no strong reason
not to enable it. at least it's required for ROCK Pi E.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- add support for compressed kernel for rk3308
- prepare support for fdtoverlay for rk3328
tested on ROCK Pi S 256MB, ROCK Pi E 2GB, and ROCK Pi 4A 4GB with
linux-next-20240613 defconfig kernel.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
this is cosmetic change. no functional change is intended.
- remove redundant white spaces
- replace white spaces with tab
- align position of last letter/word
- sort lines in CFG_EXTRA_ENV_SETTINGS
- add comment after #endif
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The pcie1ln_sel bits for the RK3588 are getting set but not cleared due
to an incorrect write mask.
Use a newly introduced constant for the write mask to fix this.
Also introduce a GENMASK-based constant for PCIE30_PHY_MODE.
This fix is adapted from the upstream Linux commit by Sebastian Reichel:
55491a5fa163 ("phy: rockchip-snps-pcie3: fix clearing PHP_GRF_PCIESEL_CON bits")
Fixes: 50e54e80679b ("phy: rockchip: snps-pcie3: Add support for RK3588")
Signed-off-by: Sebastian Kropatsch <seb-dev@mail.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Misconfigured `PHP_GRF_PCIESEL` values are causing bifurcation issues,
for example on the FriendlyElec CM3588 NAS board which uses bifurcation
on both PCIe PCIe ports (all four lanes) to enable four M.2 NVMe
sockets. Without this fix, NVMe devices do not get recognized.
Correct the `PHP_GRF_PCIESEL` register configuration and simplify the
bifurcation logic, enabling proper PCIe bifurcation based on the
data-lanes property.
This fix is adapted from the upstream Linux commit by Michal Tomek:
f8020dfb311d ("phy: rockchip-snps-pcie3: fix bifurcation on rk3588")
Fixes: 50e54e80679b ("phy: rockchip: snps-pcie3: Add support for RK3588")
Signed-off-by: Sebastian Kropatsch <seb-dev@mail.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Several identifiers use "rochchip" instead of "rockchip".
Fix this by replacing every instance of "rochchip" with "rockchip".
Signed-off-by: Sebastian Kropatsch <seb-dev@mail.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Replace "rochchip" by "rockchip" in two instances.
Signed-off-by: Sebastian Kropatsch <seb-dev@mail.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The NanoPi R6S is a SBC by FriendlyElec based on the Rockchip RK3588s.
It comes with 4GB or 8GB of RAM, a microSD card slot, 32GB eMMC storage,
one RTL8211F 1GbE and two RTL8125 2.5GbE Ethernet ports, one USB 2.0
Type-A and one USB 3.0 Type-A port, a HDMI port, a 12-pin GPIO FPC
connector, a fan connector, IR receiver as well as some buttons and LEDs.
Add initial support for this board using the upstream devicetree sources.
Kernel commit:
f1b11f43b3e9 ("arm64: dts: rockchip: Add support for NanoPi R6S")
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Sebastian Kropatsch <seb-dev@mail.de>
The NanoPi R6C is a SBC by FriendlyElec based on the Rockchip RK3588s.
It comes with 4GB or 8GB of RAM, a microSD card slot, optional 32GB eMMC
storage, one M.2 M-Key connector, one RTL8211F 1GbE and one RTL8125
2.5GbE Ethernet port, one USB 2.0 Type-A and one USB 3.0 Type-A port, a
HDMI port, a 30-pin GPIO header as well as multiple buttons and LEDs.
Add initial support for this board using the upstream devicetree sources.
Tested in U-Boot proper:
- Booting from eMMC works
- 1GbE Ethernet works using the eth_eqos driver (tested by ping)
- 2.5GbE Ethernet works using the eth_rtl8169 driver (tested by ping),
but the status LEDs on this specific port currently aren't working
- NVMe SSD in M.2 socket does get recognized (tested with `nvme scan`
followed by `nvme details`)
Kernel commit:
d5f1d7437451 ("arm64: dts: rockchip: Add support for NanoPi R6C")
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Sebastian Kropatsch <seb-dev@mail.de>
This enables PCIe support on Tiger as exposed on
Q7_PCIE[0123]_[RT]X_[PN] signals and more specifically on the `PCI
Express` connector on the Haikou devkit.
This was tested with a PCIe to NVMe adapter (e.g.
https://www.amazon.de/dp/B07RZZ3TJG).
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jaguar has an M.2 M-KEY slot for NVMes, connected to the PCIe3 4-lane
PHY on RK3588.
CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y is technically not necessary since
it's required only for the M.2 E-KEY slot on the main PCB, but that is
used typically for WiFi+BT modules, or on the mezzanine connector but
the features exposed behind that connector aren't supported in U-Boot
(no DT for it right now). However, if the PHY driver is missing, we get
the following error message:
pcie_dw_rockchip pcie@fe170000: failed to get pcie phy (ret=-19)
and you would need to know which PCIe controller that is before deciding
to ignore it. While after enabling the PHY driver, we are greeted with:
pcie_dw_rockchip pcie@fe170000: PCIe-2 Link Fail
which is a bit more acceptable (to me).
The other option would be to disable the PCIe2 PHYs/controllers in the
DT, which I'm not too fond of.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Jaguar SBC provides an M.2 slot connected to the pcie3 controller.
In contrast to a number of other boards the pcie-refclk is gpio-controlled,
so the necessary clock and is added to the list of pcie3 clocks.
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20240423074956.2622318-1-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: 0ec7e1096332bc2b9bc881c21cfd234058f747b3 ]
(cherry picked from commit 76a89655ae740dddb57187b5b52071ed99187452)
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
ROCK Pi E v3.0 uses DDR4 SDRAM instead of DDR3 SDRAM used in v1.2x.
prepare new rk3328-rock-pi-e-v3.dts in u-boot which just includes
upstream rk3328-rock-pi-e.dts.
defconfig still uses
CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-rock-pi-e.dtb"
because v3.0 and prior are compatible.
Suggested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
inno_poll passes the reg offset that is used by readl_poll_sleep_timeout
without any base addr.
Fix it.
Bug:
inno_hdmi_phy phy@ff430000: Pre-PLL locking failed
inno_hdmi_phy phy@ff430000: PHY: Failed to power on phy@ff430000: -110.
failed to power on phy (ret=-110)
inno_hdmi_phy phy@ff430000: Pre-PLL locking failed
inno_hdmi_phy phy@ff430000: PHY: Failed to power on phy@ff430000: -110.
failed to power on phy (ret=-110)
Fixes: aa2271184603 ("phy: rockchip: Add Rockchip INNO HDMI PHY driver")
Suggested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
No meaningful changes were made to this SoM since February 2021. Nobody
from Theobroma has booted anything recent on that product since July
2021 at the latest. The product isn't available to buy anymore and
disappeared from our website.
This product is therefore unmaintained and it would be disingenuous to
say the opposite, so drop support for RK3368 Lion.
If you're a user of Lion, feel free to revert this patch or contact our
sales/support department.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
It turns out only Puma had a working git:// URL. Though that is now
fixed, having HTTPS URLs make it easier to directly reach our cgit
webserver to check what's up without having to change the URL manually.
Depending on your terminal settings, this also makes it possible to
open the link from it.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
On Puma v2.1 with a KSZ9031, the Ethernet PHY often doesn't detect the
link in the 4-second default timeout.
After some boot-loop test for about a thousand boots, 70% were below
10s, 90% below 15s and 100% below 30s. Let's play it safe and make it
30s so that hopefully all links that should be detected are.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Commit 2ce40542e0eb ("power: rk8xx: properly print all supported PMICs
name") fixed all PMICs name that were broken but broke the only one that
was not broken already: RK808. This one is a special case because the ID
registers are marked as reserved and always return 0, so the variant
cannot be derived the same way it is done for other PMICs from Rockchip.
Fixes: 2ce40542e0eb ("power: rk8xx: properly print all supported PMICs name")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
In commit 100f489f58a6 ("rockchip: rk3399: Fix loading FIT from SD-card
when booting from eMMC"), the spi1 bootph properties were mistakenly
removed meaning, so re-add them back to fix SPI-NOR flash not being
found in U-Boot pre-reloc as required for RK3399 Puma.
Fixes: 100f489f58a6 ("rockchip: rk3399: Fix loading FIT from SD-card when booting from eMMC")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the IO domain on Ringneck. Based on the current HW design, this
should do nothing else than making sure vccio6 iodomain is controlled by
the GRF and not GPIO0B6.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Port the PX30 part of the Rockchip IO Domain driver from Linux.
This differs from linux version in that the io iodomain bit is enabled
in the write ops instead of in an init ops as in linux, this way we can
avoid keeping a full state of all supplies that have been configured.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There are some sub-nodes under the grf DT nodes, so add bind callback
function in syscon_px30 driver to scan them recursively.
Fixes: e9ccb2f526ed ("rockchip: add px30 architecture core")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Haikou Devkit exposes 4 buttons over GPIO so let's enable their
support so their status can be queried from the `button` command from
the CLI.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
PX30 supports ARMv8 Cryptography Extensions so let's enable it by
default for all PX30 to make FIT verification when enabled much faster.
While A35 shouldn't be impacted by ARMV8_SET_SMPEN cache coherency
according to the Kconfig help text, let's enable it just in case since
it exists in the documentation[1].
For u-boot part of the FIT image, it is now taking 5ms against currently
35ms. fdt-1 check lowered from 3ms to <1ms. atf-1 from 6ms to <1ms.
[1] https://developer.arm.com/documentation/100236/0100/register-descriptions/aarch64-system-registers/cpu-extended-control-register--el1?lang=en
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This enables FIT verification in SPL for its payload (bl31, u-boot.itb,
...). This makes PX30 Ringneck match what happens on other Theobroma
boards.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
USB gadget simply doesn't work right now on PX30. Tested on PX30 EVB and
PX30 Ringneck with Linux mainline and Rockchip 5.10 Linux as well as
U-Boot.
We don't want to our users to assume that USB gadget is supported on Q7
USB P1 on Ringneck Haikou, so let's remove its support, which also
removes the ums CLI command, fastboot and Android image booting
support.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
The scan_part() function uses a struct uuid to store the little-endian
partition type GUID, but this structure should be used only to contain a
big-endian UUID. Use an efi_guid_t instead and use guidcmp() for the
comparison.
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Move the guidcmp() and guidcpy() functions to efi.h, near the definition of
the efi_guid_t type those functions deal with.
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Manorit Chawdhry <m-chawdhry@ti.com> says:
fdtfile wasn't being populated in these boards in legacy boot using
bootcmd_ti_mmc, migrate these platforms to ti_set_fdt_env.
findfdt is used by bootcmd_ti_mmc by default which used to help populate
the fdtfile. The users of findfdt from bootcmd_ti_mmc have migrated to
ti_set_fdt_env for populating fdtfile; Hence, findfdt can be removed from
bootcmd_ti_mmc having no-impact for any platform.
Remove findfdt to not print out the warning that gets set after calling
ti_set_fdt_env. viz.
"echo WARN: fdtfile already set. Stop using findfdt in script"
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
name_fdt is kept for backward compatibility but it depends on EEPROM
detection logic and some of the TI K3 platforms don't have that anymore
which causes boot failure in legacy boot flow using bootcmd_ti_mmc.
K2g platforms which uses the same file have their own override causing
this change to be no-impact for them.
Replacing name_fdt usage to fdtfile as fdtfile is populated based on
CONFIG_DEFAULT_DEVICE_TREE after using ti_set_fdt_env.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
stdboot and legacy boot depend on fdtfile. Since findfdt is getting
deprecated, move the rest of k3 platforms dependent on findfdt to
ti_set_fdt_env.
Populate fdtfile by calling ti_set_fdt_env in board files.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
By moving the earlycon definition into a dedicated variable, it's
easier to change these values in case the kernel should print on
a different serial interface.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
By moving the earlycon definition into a dedicated variable, it's
easier to change these values in case the kernel should print on
a different serial interface.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Add the rtc command for testing this device. Additionally, add smc
and cache commands to boot non-Linux firmwares on the A53.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Add i2c and rtc commands with all dependencies which are
required for testing.
Additionally, add smc and cache commands to boot Zephyr on the A53.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Vasileios Amoiridis <vassilisamir@gmail.com> says:
This patch adds support to save the bootcount variable in a file located in
FAT filesystem. Up to now, there was support only for EXT filesystem.
The bootcount documentation was using "unattended" while it probably
intending to say "unintended"
Signed-off-by: Vasileios Amoiridis <vasileios.amoiridis@cern.ch>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Add support to save boot count variable in ANY filesystem. Tested with
FAT and EXT.
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Philip Oberfichtner <pro@denx.de>
Signed-off-by: Vasileios Amoiridis <vasileios.amoiridis@cern.ch>
On some SoCs, like Qualcomm SoCs, the PSCI cluster power domain
is used by system-wide firmware interfaces to make sure none
of the CPUs are suspended before submitting requests.
While on U-boot we only use the first core and we never
suspend it, the Device Tree still references it and blocks
those nodes to be probed.
Simply bind the PSCI power-domain subnoded to a stub power
domain driver in order to solve the runtime dependencies.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Nothing really major here, some rework of the SPL PMIC drivers, adding
support for the AXP717 on the way, which is showing up on newer boards
now, most prominently some Anbernic handheld gaming devices. The rest
is enabling Ethernet and SPI boot on the Allwinner V3s SoC, plus two
fixes. This also updates the "traditional U-Boot" DTs to that of kernel
v6.9. I will look into upgrading some SoCs to dts/upstream in the
coming cycle, though this will not cover all SoCs for now, as we carry
some non-mainline fix to improve compatibility with older kernels. Will
see how it goes, but for now we stick with the "old way".
The branch survived the gitlab CI run, and Linux boot testing on some
selected boards.
The driver is trying to read the "spi-max-frequency" property of the
*controller* driver node. There is no such property. The
"spi-max-frequency" property belongs to the SPI devices on the bus.
Right now, the driver will always fall back to the default value of 1MHz
and thus flash reads are very slow with just about 215kb/s.
In fact, the SPI uclass will already take care of everything and we just
have to clamp the frequency to the values the driver/hardware supports.
Thus, drop the whole max_hz handling.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
The BootROM in the Allwinner H616 tries to load the initial boot code
from sector 16 (8KB) of an SD card or eMMC device, but also looks at
sector 512 (256KB). This helps with GPT formatted cards.
A "high" boot offset is also used on previous SoCs, but it's sector 256
(128KB) there instead.
Extend the existing offset calculation code to consider the different
sector offset when running on an H616 SoC. This allows to load U-Boot
on any H616 device when the SPL is not located at 8KB.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Ryan Walklin <ryan@testtoast.com>
The V3s is identical regarding register layout, clocks and resets to
the sun6i variants. Therefore, we can just add the MACH_SUN8I_V3S to
the sun6i compatible ones.
SPI boot was tested on a custom board with a Gigadevice GD25Q64 8MiB
SPI flash.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Add the compatible string for the emac found on the V3s SoC. The SoC
only supports the internal PHY. There are no (R)MII signals on any pins.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Add the clock gate registers as well as the reset register bits for the
EMAC and EPHY for the V3s. These are needed by the sun8i network driver.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
