The production DH i.MX8MP DHCOM SoM rev.200 uses updated PHY MDIO addresses
for the Fast ethernet PHYs. Update the base SoM DT and SoM rev.100 backward
compatibility DTO to cater for this change.
Since the MDIO address adjustment is now also in the rev.100 SoM DTO, not
only in the rev.100 PDK3 DTO, update Makefile accordingly as well, else the
DTC would complain about the DTO overriding the 'reg' property without also
updating the node unit-address, which is not doable without duplicating the
entire PHY node in the DTO, which leads to large amount of duplication with
no gain.
Fixes: 9de599ec3d59 ("arm64: dts: imx8mp: Update i.MX8MP DHCOM SoM DT to production rev.200")
Signed-off-by: Marek Vasut <marex@denx.de>
Enable PCA953x GPIO expander driver in DH i.MX8MP DHCOM PDK2 configuration.
The PCA9539 GPIO expander is used on production DH i.MX8MP DHCOM SoM rev.200.
This is already enabled in DH i.MX8MP DHCOM PDK3 configuration so align the
two configurations.
Fixes: 9de599ec3d59 ("arm64: dts: imx8mp: Update i.MX8MP DHCOM SoM DT to production rev.200")
Signed-off-by: Marek Vasut <marex@denx.de>
Enable 'cat' command to print file from filesystem to stdout.
Enable 'xxd' command to hexdump file from filesystem to stdout.
Signed-off-by: Marek Vasut <marex@denx.de>
The older i.MX8M Mini Verdin SoMs may came with 20 MHz SPI CAN controller
oscillator, the newer SoMs always use 40 MHz oscillator. Handle both by
overriding the oscillator frequency just before booting the kernel.
These are the known variants with 20 MHz oscillator:
- 0055, V1.1A, V1.1B, V1.1C and V1.1D, use a 20MHz oscillator
- 0059, V1.1A and V1.1B, use a 20MHz oscillator
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
- Re-instate the zlib update, so we can fix it for this release,
assorted whitespace cleanups, allow mkimage to 'auto-conf' signing of
scripts, enhance ELF image support, add more HW rev support to e1000
driver, update am64x_evm config, correct mpc8xxx watchdog, update
phycore-am6 docs.
Now that the release has happened, bring back the update to zlib.
This reverts commit bbacdd3ef7762fbdeab43ceea5205d1fd0f25bbd.
Signed-off-by: Tom Rini <trini@konsulko.com>
Timer value is a 16 bits calculated from the wanted timeout and the
system clock. On powerpc/8xx, a timeout of 2s gives a value which
is over U16_MAX so U16_MAX shall be used. But the calculation is
casted to u16 so at the end the result is 63770 instead of 128906.
So the timer gets loaded with 63770 instead of 65535. It is not
a big difference in that case, but lets make the code correct and
cast to u32 instead of u16.
Fixes: 26e8ebcd7cb7 ("watchdog: mpc8xxx: Make it generic")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
This patch fixes the I225 hardware default value
at 0x15FD meaning empty flash image
or the NVM configuration loading failed
Signed-off-by: Marjolaine Amate <marjolaine.amate@odyssee-systemes.fr>
This patch adds support for Intel Foxville I226
devices LM,V,I,K in e1000 driver.
Signed-off-by: Marjolaine Amate <marjolaine.amate@odyssee-systemes.fr>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
The board has the TCA9554 I2C GPIO expander chip for expansion
board presence detection logic.
Enable the relevant I2C GPIO drivers.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Some operating systems (e.g. seL4) and embedded applications are ELF
images. It is convenient to use FIT-images to implement trusted boot.
Added "elf" image type for booting using bootm command.
Signed-off-by: Maxim Moskalets <maximmosk4@gmail.com>
U-Boot configured for verified boot with the "required" option set to
"conf" also checks scripts put in FIT images for a valid signature, and
refuses to source and run such a script if the signature for the
configuration is bad or missing. Such a script could not be packaged
before, because mkimage failed like this:
% tools/mkimage -T script -C none -d tmp/my.scr -f auto-conf -k tmp -g dev -o sha256,rsa4096 my.uimg
Failed to find any images for configuration 'conf-1/signature'
tools/mkimage Can't add hashes to FIT blob: -1
Error: Bad parameters for FIT image type
This is especially unfortunate if LEGACY_IMAGE_FORMAT is disabled as
recommended.
Listing the script configuration in a "sign-images" subnode instead,
would have added even more complexity to the already complex auto fit
generation code.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Various minor fixes and improvements:
* Fix Qualcomm SPMI v5 support
* Move default environment to a file
* Add support for special pins (e.g ufs/mmc reset/data pins)
* IPQ moves to OF_UPSTREAM and receives some cleanup and MAINTAINERS
changes
* Add a reset driver for devices without PSCI
* msm8916 USB clock improvements for mobile devices
Branch contains minor improvemets for existing tegra devices along
with bring up of 4 new devices (ASUS Transformers T20, Microsoft
Surface RT, Lenovo Ideapad Yoga 11 and WEXLER Tab 7t).
This change was brought in by accident, revert.
This reverts commit 51aabf50e57f5139de31a4850347edbad8bb338b.
Signed-off-by: Tom Rini <trini@konsulko.com>
The dm_usb_gadget_handle_interrupts() is not implemented by any USB
gadget controller drivers which do enable DM_USB_GADGET anymore. Set
the symbol as non-weak.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3
Link: https://lore.kernel.org/r/20240614005309.34433-12-marek.vasut+renesas@mailbox.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Drop dm_usb_gadget_handle_interrupts() in favor of empty default
implementation of the same in drivers/usb/gadget/udc/udc-uclass.c .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3
Link: https://lore.kernel.org/r/20240614005309.34433-11-marek.vasut+renesas@mailbox.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Implement .handle_interrupts callback as a replacement for deprecated
dm_usb_gadget_handle_interrupts() function. The new callback allows
for each DM capable USB gadget controller driver to define its own
IRQ handling implementation without colliding with other controller
drivers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3
Link: https://lore.kernel.org/r/20240614005309.34433-10-marek.vasut+renesas@mailbox.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Implement .handle_interrupts callback as a replacement for deprecated
dm_usb_gadget_handle_interrupts() function. The new callback allows
for each DM capable USB gadget controller driver to define its own
IRQ handling implementation without colliding with other controller
drivers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3
Link: https://lore.kernel.org/r/20240614005309.34433-9-marek.vasut+renesas@mailbox.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Implement .handle_interrupts callback as a replacement for deprecated
dm_usb_gadget_handle_interrupts() function. The new callback allows
for each DM capable USB gadget controller driver to define its own
IRQ handling implementation without colliding with other controller
drivers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3
Link: https://lore.kernel.org/r/20240614005309.34433-8-marek.vasut+renesas@mailbox.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Implement .handle_interrupts callback as a replacement for deprecated
dm_usb_gadget_handle_interrupts() function. The new callback allows
for each DM capable USB gadget controller driver to define its own
IRQ handling implementation without colliding with other controller
drivers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3
Link: https://lore.kernel.org/r/20240614005309.34433-7-marek.vasut+renesas@mailbox.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Implement .handle_interrupts callback as a replacement for deprecated
dm_usb_gadget_handle_interrupts() function. The new callback allows
for each DM capable USB gadget controller driver to define its own
IRQ handling implementation without colliding with other controller
drivers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3
Link: https://lore.kernel.org/r/20240614005309.34433-6-marek.vasut+renesas@mailbox.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Implement .handle_interrupts callback as a replacement for deprecated
dm_usb_gadget_handle_interrupts() function. The new callback allows
for each DM capable USB gadget controller driver to define its own
IRQ handling implementation without colliding with other controller
drivers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3
Link: https://lore.kernel.org/r/20240614005309.34433-5-marek.vasut+renesas@mailbox.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Implement .handle_interrupts callback as a replacement for deprecated
dm_usb_gadget_handle_interrupts() function. The new callback allows
for each DM capable USB gadget controller driver to define its own
IRQ handling implementation without colliding with other controller
drivers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3
Link: https://lore.kernel.org/r/20240614005309.34433-4-marek.vasut+renesas@mailbox.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Implement .handle_interrupts callback as a replacement for deprecated
dm_usb_gadget_handle_interrupts() function. The new callback allows
for each DM capable USB gadget controller driver to define its own
IRQ handling implementation without colliding with other controller
drivers.
Keep the dm_usb_gadget_handle_interrupts() in this driver for non-DM
case for now, until this driver gets fully converted to DM USB gadget.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3
Link: https://lore.kernel.org/r/20240614005309.34433-3-marek.vasut+renesas@mailbox.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Introduce .ops for USB_GADGET_GENERIC uclass. The first new ops is
.handle_interrupts which must be implemented by DM capable USB gadget
controller drivers and must implement interrupt handling similar to
dm_usb_gadget_handle_interrupts(). This patch currently provides weak
dm_usb_gadget_handle_interrupts() implementation which is overridden by
the drivers, but this will be removed once conversion to handle_interrupts
callback is complete.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3
Link: https://lore.kernel.org/r/20240614005309.34433-2-marek.vasut+renesas@mailbox.org
[mkorpershoek: fixed trivial typo in commit message]
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Use the .match_ep() callback instead of workaround in core code.
Replace descriptor parsing with ch9 macros with the same effect.
Drop the SPL specific behavior, it is unclear why SPL should even
be special.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tested-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on vim3
Link: https://lore.kernel.org/r/20240609213449.194762-6-marek.vasut+renesas@mailbox.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
If .match_ep() callback returns non-NULL endpoint, immediately check
its usability and if the returned endpoint is usable, stop search and
return the endpoint. Otherwise, continue with best effort search for
usable endpoint.
Currently the code would attempt the best effort search in any case,
which may find another unexpected endpoint. It is likely that the
intention of the original code was to stop the search early.
Fixes: 77dcbdf3c1ce ("usb: gadget: Add match_ep() op to usb_gadget_ops")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tested-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on vim3
Link: https://lore.kernel.org/r/20240609213449.194762-5-marek.vasut+renesas@mailbox.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
The only actually used gadget_is_*() functions are the one for DWC3
used in epautoconf.c usb_ep_autoconfig() and one for MUSB in ether.c.
The DWC3 one should be fixed in some separate patch.
Inline the gadget_is_dwc3() and stop using ifdefs in favor of
IS_ENABLED() macro.
The rest of gadget_is_*() calls in usb_ep_autoconfig() can never
be anything but 0, since those gadgets are not supported in U-Boot,
so remove all that unused code. Remove gadget_chips.h as well.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tested-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on vim3
Link: https://lore.kernel.org/r/20240609213449.194762-4-marek.vasut+renesas@mailbox.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
The bcdDevice field is defined as
|Device release number in binary-coded decimal
in the USB 2.0 specification. We use this field to distinguish the UDCs
from each other. In theory this could be used on the host side to apply
certain quirks if the "special" UDC in combination with this gadget is
used. This hasn't been done as far as I am aware. In practice it would
be better to fix the UDC driver before shipping since a later release
might not need this quirk anymore.
This patch removes the newly unused function. Linux stopped using this
functionality in 2012, remove it from U-Boot as well.
Matching Linux kernel commit:
ed9cbda63d45 ("usb: gadget: remove usb_gadget_controller_number()")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tested-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on vim3
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Link: https://lore.kernel.org/r/20240609213449.194762-3-marek.vasut+renesas@mailbox.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
The bcdDevice field is defined as
|Device release number in binary-coded decimal
in the USB 2.0 specification. We use this field to distinguish the UDCs
from each other. In theory this could be used on the host side to apply
certain quirks if the "special" UDC in combination with this gadget is
used. This hasn't been done as far as I am aware. In practice it would
be better to fix the UDC driver before shipping since a later release
might not need this quirk anymore.
This patch converts this gadget to use the U-Boot version instead of a
random 2 or 3 plus the UDC number. Linux stopped using this functionality
in 2012, remove it from U-Boot as well.
Matching Linux kernel commit:
ed9cbda63d45 ("usb: gadget: remove usb_gadget_controller_number()")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tested-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on vim3
Link: https://lore.kernel.org/r/20240609213449.194762-2-marek.vasut+renesas@mailbox.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
The bcdDevice field is defined as
|Device release number in binary-coded decimal
in the USB 2.0 specification. We use this field to distinguish the UDCs
from each other. In theory this could be used on the host side to apply
certain quirks if the "special" UDC in combination with this gadget is
used. This hasn't been done as far as I am aware. In practice it would
be better to fix the UDC driver before shipping since a later release
might not need this quirk anymore.
This patch converts this gadget to use the U-Boot version instead of a
random 2 or 3 plus the UDC number. Linux stopped using this functionality
in 2012, remove it from U-Boot as well.
Matching Linux kernel commit:
ed9cbda63d45 ("usb: gadget: remove usb_gadget_controller_number()")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tested-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3
Link: https://lore.kernel.org/r/20240609213449.194762-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Commit ee1d8aa5ecf7 ("spmi: msm: support controller version 7") broke
support for channels > 128 on v5 controllers, resulting in some
peripherals (like the power button / pon) working but others (like
gpios) reading bogus data.
Correct max_channels for v5 controllers.
Fixes: ee1d8aa5ecf7 ("spmi: msm: support controller version 7")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Make use of CONFIG_DEFAULT_ENV_FILE and move the default qcom
environment to a file under board/qualcomm.
This is much cleaner and means we don't need to recompile on changing
the environment.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Most devices have buttons exposed via the PMIC, the button polling
therefore triggers a log spam if debug logging is enabled.
Demote these to debug() so that they aren't printed unless LOG_DEBUG is
defined explicitly for this file.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Add the special pins configuration data to allow setup the bias
of the UFS and SDCard pins on the SM8650 SoC.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Add the special pins configuration data to allow setup the bias
of the UFS and SDCard pins on the SM8550 SoC.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Use the previously introduced msm_special_pin_data to setup the special
pins configuration if the SoC driver have them specified.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
In order to help setup pin configuration for special pins (UFS, SDCard),
introduce the msm_special_pin_data struct largely inspired from the
Linux conterpart but with only U-Boot required fields.
This struct is added to the pins_data to allow specifying the special
pins data for each SoC.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
I2C clocks are not initialized by the SBL, so lets add support for clocks
required by both of the QUP I2C controllers.
BLSP1 AHB clock is already initialized by SBL, but QUP I2C driver is
requesting it so we have to add it to the enable list.
Based off QCS404 clock driver.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Pinctrl drivers were moved to a dedicated directory but the entry was never
updated, so add the pinctrl-ipq4019 driver entry.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
The reset handling was added to the clock drivers but the entry was never
updated, so add the clock-ipq4019 driver instead.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
The separate clock and reset dt-bindings for IPQ40XX were merged into one
recently, but the entry was not updated so do it now.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
We want to use OF_UPSTREAM on IPQ40XX as its well supported upstream, so
lets drop our downstream DTSI.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Now that drivers are compatible enough with the upstream DTS, there is no
reason to not use the upstream DTS, so imply OF_UPSTREAM by default.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
