Add support for the Polyhex Debix Model A SBC board.
It is an industrial grade single board computer based on
NXP's i.MX 8M Plus.
Currently supported interfaces are:
- Serial console
- Micro SD
- eQOS and FEC Ethernet
imx8mp-debix-model-a.dts is taken from Linux 6.3.
Signed-off-by: Gilles Talis <gilles.talis@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Later versions of Colibri iMX7D V1.1B modules use a "new" SoC fusing. The
difference lies in whether we enable the boot ROM to use the eMMC reset
signal. Depending on the SoC fuse, the boot ROM configures this pin as a
GPIO output to drive the reset signal. Our eMMC vs NAND detection
currently only sets that signal to a GPIO without explicitly setting any
direction. Previously, by default, it was set as an input. As the boot ROM
now configures it as an output, we receive a value of zero instead of one,
indicating the absence of the pull-up on eMMC modules.
To fix this, set the SION bit, allowing the reading back of the value
even if it is configured as an output by the boot ROM. It's important to
note that with the new SoC fusing, we now read back what the boot ROM
drives rather than the real value caused by the pull-up resistor. However,
if it were ever driven low, the eMMC would permanently be reset.
In addition, remove hard-coded variant in the eMMC build case as since the
commit 0c39564d0281 ("toradex: colibri_imx7: Enable nand/emmc detection
and set boot variant") will anyways always get overridden by the detection
routing in board code.
Fixes: 0c39564d ("toradex: colibri_imx7: Enable nand/emmc detection and set boot variant")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
- StarFive: Add StarFive watchdog driver
- VisionFive2: Support device tree overlay for VisionFive2 board
- Andes: Fix PLIC-SW setting
- RISC-V: Fix NVMe support by implying NVME_PCI for QEMU
- RISC-V: Fix binman for 64 bit format load address
To quote the author:
Currently bootmeth_efi crashes while doing a network (dhcp) boot.
This patch series fixes issues and both network and disk boot works.
# Do not modify or remove the line above.
# Everything below it will be ignored.
#
# Please enter a commit message to explain why this merge is necessary,
# especially if it merges an updated upstream into a topic branch.
#
# An empty message aborts the commit.
While booting with efi, if fdt isn't available externally,
just use the built-in one.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Shantur Rathore <i@shantur.com>
device tree overlay support requires fdtoverlay_addr_r to be set
before
~~~~~~
Invalid fdtoverlay_addr_r for loading overlays
after
~~~~~
Retrieving file: /boot/overlay/rtc-ds3231.dtbo
Signed-off-by: John Clark <inindev@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
If the xHC has a problem with our STOP ENDPOINT command, it is likely to
return a completion directly instead of first a transfer event for the
in-progress transfer. Handle that more gracefully.
We still BUG() on the error code, but at least we don't end up timing
out on the event and ending up with unexpected event errors.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
This is a hacky way to have this file included in all source files that
include common.h, instead just include from the files that need it.
Signed-off-by: Andrew Davis <afd@ti.com>
These are leftover definitions. While here cleanup some leftover comments.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To quote the author:
This series fixes an issue where the FAT type (FAT12, FAT16) is not
correctly detected, e.g. when the BPB field BS_FilSysType contains the
valid value "FAT ".
This issue occures, for example, if a partition is formatted by
swupdate using its diskformat handler. swupdate uses the FAT library
from http://elm-chan.org/fsw/ff/ internally.
See https://groups.google.com/g/swupdate/c/7Yc3NupjXx8 for a
discussion in the swupdate mailing list.
Please refer to the commit messages for more details.
1. Added bootsector checks
Most tests from https://www.win.tue.nl/~aeb/linux/fs/fat/fat-2.html
are added in the commit 'fs: fat: add bootsector validity check'.
Only the tests VIII, IX and X are not implemented.
I also checked the Linux kernel code (v6.6) and did not find any
checks on 'vistart->fs_type'. This is the reason why is skipped them
here.
See section '2. Size comparisons' for the impact on the binary size.
2. Size comparisons
I executed bloat-o-meter from the Linux kernel for an arm64
target (config xilinx_zynqmp_mini_emmc0_defconfig):
Comparison of the binary spl/u-boot-spl between master (rev
e17d174773e9ba9447596708e702b7382e47a6cf) and this patch
series (including the added validity checks of the boot sector):
add/remove: 0/0 grow/shrink: 1/1 up/down: 100/-12 (88)
Function old new delta
read_bootsectandvi 308 408 +100
fat_itr_root 444 432 -12
Total: Before=67977, After=68065, chg +0.13%
When compare the size of the binary spl/u-boot-spl between master this
series without the the validity checks of the boot sector:
add/remove: 0/0 grow/shrink: 0/2 up/down: 0/-24 (-24)
Function old new delta
read_bootsectandvi 308 296 -12
fat_itr_root 444 432 -12
Total: Before=67977, After=67953, chg -0.04%
So the size of the spl on this arm64 target increases by 88 bytes for
this series. When i remove the validity check the size decreases by 24 bytes.
This fixes an issue where the FAT type (FAT12, FAT16) is not
correctly detected, e.g. when the BPB field BS_FilSysType contains the
valid value "FAT ".
According to the FAT spec the field BS_FilSysType has only
informational character and does not determine the FAT type.
The logic of this code is based on the linux kernel implementation
from the file fs/fat/inode.c function fat_fill_super().
For details about FAT see http://elm-chan.org/docs/fat_e.html
Signed-off-by: Christian Taedcke <christian.taedcke@weidmueller.com>
To quote the author:
This series imports generic versions of ioread_rep/iowrite_rep and
reads/writes from Linux. Some cleanup is done to make sure that all
platforms have proper defines for implemented functions and there are no
redefinitions.
Currently {read,write}s{b,w,lq}() functions are available only on some
architectures, and there are no io{read,write}{8,16,32,64}_rep()
functions in u-boot. This patch adds generic versions that may be used
without arch-specific implementation.
Since some of added functions were already added locally in some files,
remove them to avoid redeclaration errors.
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
To quote the author:
The show_board_info() function was adjusted to weak so that it could be
entirely replaced with a board-specific implementation.
The intended way for boards to provide their own information is via a
sysinfo driver. But currently there is no way to show anything other
than the model name.
This series adds support for showing a few more items, in a way that is
easy for boards to extend.
Since there is already a weak checkboard() function, we don't need to
have two levels of weak function here. So this series drops the weak
attribute from show_board_info()
Existing boards will see a slight change in output, in that the model
name will appear first, before any custom output. If that is a problem,
then the solution is to implement a sysinfo driver for the board.
At present only the model name is shown on start. Some boards want to
display more information. Add some more options to allow display of the
manufacturer as well as the version and date of any prior-stage
firmware.
This is useful for coreboot, at least. If other boards have more
information to display, it is easy to add it, now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Red Hat, Inc. donates a part of its device ID range [1] to QEMU,
to be used for virtual devices. This commit adds several typical
devices that are useful in U-Boot.
[1] https://www.qemu.org/docs/master/specs/pci-ids.html
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
u-boot-dfu-next-20231124
- Make dfu entity name size configurable in KConfig
- Implement start-stop for UMS (graceful shutdown via eject)
- Improve help messages for cmd/bind
- Improve help message for udc bind failures
Modify spi and usb aliases name.
Add dt-binding for usb phy define and fix usb phy reset error.
Add tpm/otpee and host_intf node.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Draco is a family of 3 boards: thuban, rastaban & etamin. Rename all
targets of the family adding the draco- prefix to increase readibility
and simplify future commits about concerning all boards of the family.
The name draco was initially used for the first target. It's deprecated
since a 2nd target was introduced. Unfortunately the draco target was
copied to the thuban target instead to be renamed. Remove it to save
unnecessary maintenance effort.
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
Add CONFIG_DFU_NAME_MAX_SIZE to change the proper size.
If name is longer than default size, it can do wrong behavior during updating
image. So it need to change the proper maximum size.
This patch is proviced the solution to change value with configuration.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Link: https://lore.kernel.org/r/20220620111354.448512-1-jh80.chung@samsung.com
[mkorpershoek: fixed build errors for dfu.h includes]
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
This adds the URI device path option for 'boot add' subcommand.
User can add the URI load option for downloading ISO image file
or EFI application through network. Currently HTTP is only supported.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
When the image loaded by efibootmgr returns, efibootmgr
needs to clean the resources. Adding the event of returning
to efibootmgr is useful to simplify the implementation.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
const classifier is missing in EventGroup parameter of
CreateEventEx(). Fix it to remove the compiler warning.
NotifyContext parameter of CreateEventEx() is also defined
with const in UEFI specification, but NotifyContext parameter
of CreateEvent() is defined without const.
Since current implementation calls the common efi_create_event()
function from both CreateEventEx() and CreateEvent() services,
NotifyContext parameter leaves as is.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
User needs to call several functions to create the ramdisk
with blkmap.
This adds the utility function to create blkmap device and
mount the ramdisk.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Current wget takes the target uri in this format:
"<http server ip>:<file path>" e.g.) 192.168.1.1:/bar
The http server ip address must be resolved before
calling wget.
This commit adds the utility function runs wget with dhs.
User can call wget with the uri like "http://foo/bar".
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
EFI applications can be very large and thus used to cause boot failures
when malloc() space was exhausted.
A recent changed fixed this by using the kernel_addr_r environment var
as the address of the buffer. However, it still frees the buffer when
the bootflow is discarded.
Fix this by introducing a flag to indicate whether the buffer was
allocated, or not.
Note that kernel_addr_r is not the last word here. It might be better
to use lmb to place images. But there is a lot of refactoring to do
before we can remove the environment variables. The distro scripts rely
on them so it is safe for bootstd to do so too.
Fixes: 6a8c2f9781c bootstd: Avoid allocating memory for the EFI file
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported by: Simon Glass <sjg@chromium.org>
Reported by: Shantur Rathore <i@shantur.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Shantur Rathore <i@shantur.com>
- squashfs improvements, remove common.h in some places, assorted code
fixes, fix a few CONFIG symbol names in Kconfig files, bring in
linux's <linux/time.h> conversion functions, poplar updates, bcb
improvements.
Currently BCB C API only allows to modify 'command' BCB field.
Extend it so that we can also read and modify all the available
BCB fields (command, status, recovery, stage).
Co-developed-by: Cody Schuffelen <schuffelen@google.com>
Signed-off-by: Cody Schuffelen <schuffelen@google.com>
Signed-off-by: Dmitrii Merkurev <dimorinny@google.com>
Cc: Eugeniu Rosca <erosca@de.adit-jv.com>
Cc: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Cc: Sean Anderson <sean.anderson@seco.com>
Cc: Cody Schuffelen <schuffelen@google.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on vim3
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Currently BCB command-line, C APIs and implementation only
support MMC interface. Extend it to allow various block
device interfaces.
Signed-off-by: Dmitrii Merkurev <dimorinny@google.com>
Cc: Eugeniu Rosca <erosca@de.adit-jv.com>
Cc: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Cc: Sean Anderson <sean.anderson@seco.com>
Cc: Cody Schuffelen <schuffelen@google.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on vim3
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Adjust mem layout, providing more space for linux kernel image.
This fixes the problem:
ERROR: FDT image overlaps OS image (OS=0x30000000..0x32580000)
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Currently there are no defines for time conversion in time.h, which
leads to drivers declaring those locally or not using defines at all, so
add them from Linux.
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the spi load method to use spl_load. The address used for
LOAD_FIT_FULL may be different, but there are no in-tree users of that
config. Since payload_offs is only used without OS_BOOT, we defer its
initialization.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the semihosting load method to use spl_load. As a result, it
also adds support for LOAD_FIT_FULL and IMX images.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
This converts the blk load method (used exclusively by NVMe) to use
spl_load. As a consequence, it also adds support for LOAD_FIT_FULL and
IMX images.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the nor load method to use spl_load. As a result it also
adds support for LOAD_FIT_FULL. Since this is the last caller of
spl_load_legacy_img, it has been removed.
We can't load FITs with external data with SPL_LOAD_FIT_FULL, so disable the
test in that case. No boards enable SPL_NOR_SUPPORT and SPL_LOAD_FIT_FULL, so
this is not a regression.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the net load method to use spl_load. As a result, it also
adds support for LOAD_FIT_FULL and IMX images.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the nand load method to use spl_load. nand_page_size may not
be valid until after nand_spl_load_image is called (see e.g. fsl_ifc_spl),
so we set bl_len in spl_nand_read. Since spl_load reads the header for us,
we can remove that argument from spl_nand_load_element.
There are two possible regressions which could result from this commit.
First, we ask for a negative address from spl_get_load_buffer. That is,
instead of
header = spl_get_load_buffer(0, sizeof(*header));
we do
header = spl_get_load_buffer(-sizeof(*header), sizeof(*header));
this could cause a problem if spl_get_load_buffer does not return valid
memory for negative offsets. Second, we now set bl_len for legacy images.
This can cause memory up to a bl_len - 1 before the image load address to
be written, which might not have been the case before. If this turns out to
be a problem, we can add an option for a bounce buffer.
We can't load FITs with external data with SPL_LOAD_FIT_FULL, so disable the
test in that case. No boards enable SPL_NAND_SUPPORT and SPL_LOAD_FIT_FULL, so
this is not a regression.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the mmc loader to spl_load. Legacy images are handled by
spl_load (via spl_parse_image_header), so mmc_load_legacy can be
omitted. To accurately determine whether mmc_load_image_raw_sector is used
(which might not be the case if SYS_MMCSD_FS_BOOT is enabled), we introduce
a helper config SYS_MMCSD_RAW_MODE. This ensures we can inline spl_load
correctly when a board only boots from filesystems. We still need to check
for SPL_MMC, since some boards enable configure raw mode even without MMC
support.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the fat loader to use spl_load. Some platforms are very
tight on space, so we take care to only include the code we really need.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the ext load method to use spl_load. As a consequence, it
also adds support for FIT and IMX images.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Implementers of SPL_LOAD_IMAGE_METHOD have to correctly determine what
type of image is being loaded and then call the appropriate image load
function correctly. This is tricky, because some image load functions
expect the whole image to already be loaded (CONFIG_SPL_LOAD_FIT_FULL),
some will load the image automatically using spl_load_info.read()
(CONFIG_SPL_LOAD_FIT/CONFIG_SPL_LOAD_IMX_CONTAINER), and some just parse
the header and expect the caller to do the actual loading afterwards
(legacy/raw images). Load methods often only support a subset of the
above methods, meaning that not all image types can be used with all
load methods. Further, the code to invoke these functions is
duplicated between different load functions.
To address this problem, this commit introduces a "spl_load" function.
It aims to handle image detection and correct invocation of each of the
parse/load functions.
Although this function generally results in a size reduction with
several users, it tends to bloat boards with only a single user.
This is generally because programmers open-coding the contents of this
function can make optimizations based on the specific loader. For
example, NOR flash is memory-mapped, so it never bothers calling
load->read. The compiler can't really make these optimizations across
translation units. LTO solves this, but it is only available on some
arches. To address this, perform "pseudo-LTO" by inlining spl_load when
there are one or fewer users. At the moment, there are no users, so
define SPL_LOAD_USERS to be 0.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These will soon be supported, so we need to be able to test it. Export the
lzma data and generally use the same process in spl_test_mmc_fs as
do_spl_test_load. If we end up needing this in third place in the future,
it would probably be good to refactor things out.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To allow for easier reuse of this functionality, split it off into its
own function.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Aligning addresses and sizes causes overhead which is unnecessary when we
are not loading from block devices. Remove bl_len when it is not needed.
For example, on iot2050 we save 144 bytes with this patch (once the rest of
this series is applied):
add/remove: 0/0 grow/shrink: 0/3 up/down: 0/-144 (-144)
Function old new delta
spl_load_simple_fit 920 904 -16
load_simple_fit 496 444 -52
spl_spi_load_image 384 308 -76
Total: Before=87431, After=87287, chg -0.16%
We use panic() instead of BUILD_BUG_ON in spl_set_bl_len because we still
need to be able to compile it for things like mmc_load_image_raw_sector,
even if that function will not be used.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
