AM64 ES2.0 bootrom seems to enable WAIT0EDGEDETECTION interrupt.
This causes a lockup at A53 SPL when accessing NAND controller
or ELM registers.
A good option would be to softrest GPMC block at probe
but this cannot be done for AM64 as SOFTRESET bit is marked
as reserved in SYSCONFIG register.
Fix the issue by disabling all IRQs at probe.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Some platforms (such as the Lichee Pi 4A) have their dwmac device
addressable only in high memory space. Storing the node's base address
on 32 bits is not possible in such case.
Use platform's physical address type to store the base address.
Signed-off-by: Nils Le Roux <gilbsgilbert@gmail.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
ID code is added for zu67dr_SE, zu11eg_SE, zu19eg_SE and zu47dr_SE
variants. SE is the select edition of restricted devices with the
capabilities.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20240123045715.893652-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Recent i.MX8MP DTs use new fsl,imx6ul-ecspi compatible string instead
of the fsl,imx51-ecspi compatible string. Add the new compatible string
to fix ECSPI operation on i.MX8MP.
For details, see Linux:
48d74376fb68 ("arm64: dts: imx8mp: update ecspi compatible and clk")
8eb1252bbedf ("spi: imx: remove ERR009165 workaround on i.mx6ul")
Fixes: 451799a6ceac ("arm: dts: imx8mp: Sync the DT with kernel 6.4-rc4")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Support RPC SPI on R8A779H0 V4M SoC.
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add PLL7 support to Gen3/Gen4 common clock driver. Add initial PLL7
multiplier and divider values into table in R8A779H0 V4M clock driver.
The PLL7 is new PLL added in R8A779H0 V4M SoC. Only integer multiplication
mode is supported by PLL7. The PLL reference clock are either 16.66 MHz or
20 MHz on R8A779H0 V4M SoC, and the output frequency must be 2000 MHz. The
multiplier values fitting this requirement are calculated to 120 or 100.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
- Add USB support for phycore-imx8mp
- Fix environment corruption, reset on mx6sabresd
- Print reset cause on imx8
- Extend mkimage to support generating an image for i.MXRT FlexSPI
- Add new apalis and colibri variants
- Add support for phyBOARD-Segin-i.MX93 support
- Fix when FEC is primarily used instead of EQOS on i.MX93.
Rename nxp_c45_tja11xx structure to nxp_c45_tja1103. The driver will
support more PHYs and nxp_c45_tja11xx is too generic.
Signed-off-by: "Radu Pirea (NXP OSS)" <radu-nicolae.pirea@oss.nxp.com>
Read PHY speed from hardware instead of assuming 100Mbps by default.
The TJA1103 works only at 100Mbps, but the driver will support more PHYs.
Signed-off-by: "Radu Pirea (NXP OSS)" <radu-nicolae.pirea@oss.nxp.com>
Use a local definition for the PHY features. PHY_100BT1_FEATURES are
not defined using the 100BaseT1 bit, so keep this workaround in the driver.
Signed-off-by: "Radu Pirea (NXP OSS)" <radu-nicolae.pirea@oss.nxp.com>
This error path should return -EINVAL instead of success.
Fixes: e261fbf34785 ("blk: host_dev: Sanity check on the size of host backing file")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Add a comment to explain the code under is_secure condition of
ti_sci_do_xfer. This will help avoid confusion amongst people who may in
future touch upon this code.
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
The ti_sci driver in U-Boot has support for secure_msg as part of it's
do_xfer function. This let's U-boot send secure messages during boot up.
The protocol to send such secure messages is described as part of the
struct ti_sci_secure_msg_hdr. As part of this, there are 2 fields for
checksum and reserved that occupy the first 4 bytes of any secure
message. This is called as the secure_hdr.
As of now, the secure_hdr needs to be 0 init-ed before sending secure
messages. However the existing code was never putting the zero-inited vars
into the secure_buf, leading to possibility of the first 4 bytes of
secure_buf being possibly garbage.
Fix this by initialising the secure_hdr itself to the secure_buf
location, thus when we make secure_hdr members 0, it automatically ensures
the first 4 bytes of secure_buf are 0.
Fixes: 32cd25128bd849 ("firmware: Add basic support for TI System Control Interface (TI SCI)")
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Testing has shown that writing to eMMC using HS400 modes on RK3568
result in an ERROR.
Change the tap number for transmit clock to fix this.
Also stop DLL when config_dll() is called to disable DLL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for ddr4 on rv1126. Timing detection files are imported
from downstream Rockchip BSP u-boot. Allow selecting ddr4 ram with
define CONFIG_RAM_ROCKCHIP_DDR4.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Some ethernet PHY require being reset before a phy-id can be read back
on the MDIO bus. This can result in the following message being show
on e.g. a Radxa ROCK Pi E v1.21 with a RTL8211F ethernet PHY.
Could not get PHY for ethernet@ff540000: addr -1
Add support to designware ethernet driver to reset eth phy by calling
the eth phy uclass function eth_phy_set_mdio_bus(). The call use NULL
as bus parameter to not set a shared mdio bus reference that would be
freed when probe fails. Also add a eth_phy_get_addr() call to try and
get the phy addr from DT when DM_MDIO is disabled.
This help fix ethernet on Radxa ROCK Pi E v1.21:
=> mdio list
ethernet@ff540000:
1 - RealTek RTL8211F <--> ethernet@ff540000
Reported-by: Trevor Woerner <twoerner@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In the SMBIOS 3 entry point the Structure Table Maximum Size field was
incorrectly named max_struct_size. A Maximum Structure Size field only
exists in the SMBIOS 2.1 entry point and has a different meaning.
Call the Structure Table Length field table_maximum_size.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
For RISC-V CPUs the SMBIOS Processor ID field contains
the Machine Vendor ID from CSR mvendorid.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This patch adds an implementation of the Andes watchdog ATCWDT200 driver.
Signed-off-by: CL Wang <cl634@andestech.com>
Signed-off-by: Randolph <randolph@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmW4mGIcHGV1Z2VuLmhy
aXN0ZXZAY29sbGFib3JhLmNvbQAKCRAesx4CDqwvyBq9B/sHzeh4lWQpyU5CcO8J
WnlRn2blqL/2LzkawD6OvA7WhEYisLh2389q6pPSFqWZS8v1aNgTO4krnPDOG3a5
s7yigcBtg5KsmnM4K89+KZ/BZW4TzrSHIY4P+t1W92QtnFHEzNW/LolG6jBZnz+e
bMzi0uCGR1cgTW4IfLmuq6NajIaAXywdohMxfi/9kiNhQVT03Jux/CGoIvpJ61Bu
OKWX2KNn0o3XXK7UKdZUSzP6CyiRSplQl3eX/0shh9qPR16eSeUqh952zGxlcOZO
PKXvDMl8QxkCzRjXdg3EH2jADoaTB0maq6JutVyY+SoLiYJ9A8BUCLOIMevCVXjK
3BCH
=V29u
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2024.04-a' of https://source.denx.de/u-boot/custodians/u-boot-at91
First set of u-boot-at91 features for the 2024.04 cycle:
This set includes some DT alignments and solves a compile issue for
custom nand defconfigs.
This ports the pad drive strength register configuration which can be
already found in the Linux driver for this PHY.
Signed-off-by: Lukasz Tekieli <tekieli.lukasz@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Make sure that core SDHCI accessors are used and add
device specific card detection initialization, which
is borrowed from vendor Linux driver code.
Tested-by: Jens Maus <mail@jens-maus.de>
Tested-by: Darko Alavanja <darko.alavanja@konsulko.com>
Signed-off-by: Ivan T. Ivanov <iivanov@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
brcm,bcm2708-fb device provided by firmware on RPi5 uses
16 bits per pixel, so lets calculate framebuffer bytes
per pixel dynamically based on queried information.
Tested to work for RPi2b v1.2, RPi3b v1.3, RPi4b v1.1,
RPi2 Zero W, RPi5b v1.0.
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Tested-by: Jens Maus <mail@jens-maus.de>
Tested-by: Darko Alavanja <darko.alavanja@konsulko.com>
Signed-off-by: Ivan T. Ivanov <iivanov@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Existing gpio-gate-clock driver acts like a simple GPIO switch without any
effect on gated clock. Add actual clock actions into enable/disable ops and
implement get_rate op by passing gated clock if it is enabled.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20240110160956.4476-2-clamor95@gmail.com
[ sorted includes ]
Signed-off-by: Sean Anderson <seanga2@gmail.com>
When we call clk_get_rate(), we expect to get clock rate value as
ulong.
In that case we should not use log_ret() macro since it use internally
an int.
Otherwise we may return an invalid/truncated clock rate value.
Signed-off-by: Julien Masson <jmasson@baylibre.com>
Fixes: 5c5992cb90c ("clk: Add debugging for return values")
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/87o7erv9p4.fsf@baylibre.com
Amlogic SoCs embeds an hardware clock measure block, port it
from Linux and implement it as a UCLK_CLK with only the dump
op and fail-only xlate.
Based on the Linux driver introduced in [1].
[1] commit 2b45ebef39a2 ("soc: amlogic: Add Meson Clock Measure driver").
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231218-uboot-meson-clk-msr-v3-1-acf4d90ccfee@linaro.org
Without explicit support for VIDEO_X2R10G10B10 VIDEO_X8R8G8B8 white
will be rendered as cyan-ish. The conversion leaves to lowest 2 bits
unset for more compact code.
Signed-off-by: Janne Grunau <j@jannau.net>
Use device-tree node property names for parsing nodes instead of
indexing as indexing could be different between different SoCs based on
number of DSS entities available on that particular SoC.
Also correct the video layer naming in driver to match to actual one
being used in upstream DSS device-tree node [1].
This also fixes AM62x splash screen usage using the latest upstream DSS
device-tree nodes where hard-coded indexing which driver was using
before this patch was not matching the correct properties in the DT
node.
[1]: Upstream AM62x DSS node:
https://github.com/torvalds/linux/blob/v6.8-rc1/arch/arm64/boot/dts/ti/k3-am62-main.dtsi#L774
Fixes: 5f9f816bb8 ("drivers: video: tidss: TIDSS video driver support for AM62x")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
Devarsh Thakkar <devarsht@ti.com> says:
Move video memory reservation for SPL at end of RAM so that it does
not interefere with reservations for next stage so that the next stage
need not have holes in between for passed regions and instead it can
maintain continuity in reservations.
Also catch the bloblist before starting reservations to avoid the same
problem.
While at it, also fill missing fields in video handoff struct before
passing it to next stage.
This is as per discussions at :
For moving SPL framebuffer reservation at end of RAM:
https://lore.kernel.org/all/CAPnjgZ3xSoe_G3yrqwuAvoiVjUfZ+YQgkOR0ZTVXGT9VK8TwJg@mail.gmail.com/
For filling missing video handoff fields :
https://lore.kernel.org/all/CAPnjgZ1Hs0rNf0JDirp6YPsOQ5=QqQSP9g9qRwLoOASUV8a4cw@mail.gmail.com/
Fill video handoff fields in video_post_probe as at this point we have
full framebuffer-related information.
Also fill all the fields available in video hand-off struct as those
were missing earlier and U-boot framework expects them to be filled for
some of the functionalities.
While filling framebuffer size in video hand-off structure use the
actual framebuffer region size as derived from gd->video_top and
gd->video_bottom instead of directly using the size populated in
video_uc_plat as it contains unaligned size.
Reported-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Skip framebufer reservation if it was already reserved from previous
stage and whose information was passed using a bloblist.
Return error in case framebuffer information received from bloblist is
invalid i.e NULL or empty.
While at it, improve the debug message to make it more clear that
address in discussion is of framebuffer and not bloblist and also match
it with printing scheme followed in video_reserve function.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make the "phy-handle" property optional, which allows support
for a fixed-link phy configuration.
Thus if the "phy-handle" is present in a DT, then driver will work as
before. Otherwise, phyaddr initialization will not be necessary,
as it is not needed in case of a fixed-link config.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Infineon(Cypress) S28HS02GT is 1.8V, 2Gb (256MB) NOR Flash memory with
Octal interface. It is a dual-die package parts and has same features
with existing S28 series.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Enabling Octal DTR mode in multi-die package parts requires reister setup
for each die. That can be done by simple for-loop. write_enable() takes
effect to all die at once so we can call it before the loop. Besides we
can replace spi_mem_exec_op() calls with spansion_read/write_any_reg().
And finally, we must mask CFR2V[7:4] when changing dummy cycles, as
CFR2V[7] indicates current addressing mode and that should be 1 (4-byte
address mode) for multi-die package parts.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
s28hx_t_post_bfpt_fixup() fixes erase opcode, erase size, and page size.
s25_post_bfpt_fixup() is doing same thing including multi-die support.
We can consolidate s28hx_t_post_bfpt_fixup() and s25_post_bfpt_fixup()
into one named s25_s28_post_bfpt_fixup().
In s25_s28_post_bfpt_fixup(), set_4byte() is called to force the device to
be 4-byte addressing mode. In S28HS02GT datasheet, the B7 opcode is missing
but it works actually (confirmed).
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
s28hx_t_setup() only checks sector layout setting. To support multi-die
package parts like S28HS02GT, it needs to check device size and assign
ready() hook for multi-die package parts. These are covered in s25_setup()
so we can consolidate s28hx_t_setup() and s25_setup() into one named
s25_s28_setup().
spi_nor_wait_till_ready() at the beginning of s28hx_t_setup() can be
removed since there is no op that makes device busy state before setup.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
