Support is added for 5 new Qualcomm SoCs:
* QCM2290 and SM6115 are low and mid range SoCs used on the RB1 and RB2
respectively. SM6115 is also used in some mid-range smartphones/tablets.
Initial support includes buttons and USB (host and gadget).
* SM8250 is a flagship SoC from 2020 used on the RB5, as well as many flagship
smartphones. The board can boot to a U-Boot prompt, but is missing regulators
necessary for USB support.
* SM8550, and SM8650 are flagship mobile SoCs from 2023 and 2024
respectively. Found on many high end smartphones.
In addition:
* Support is added for the Schneider HMIBSC board.
* mach-snapdragon switches to OF_UPSTREAM
* IPQ40xx gets several regressions fixed and some overall cleanup.
* The MSM serial driver gains the ability to generate the bit-clock
automatically, no longer relying on a custom DT property.
* The Qualcomm SMMU driver gets a generic compatible (so per-SoC compatibles
don't need to be added).
* Support for the GENI I2C controller is added.
* The qcom SPMI driver has SPMI v5 support fixed, and v7 support added.
* The qcom sdhci driver gets some fixes for SDCC v5 support.
* SDM845 gains sdcard support
* Support is added for the Synopsys eUSB2 PHY driver (used on SM8550 and SM8650)
* SYS_INIT_SP_BSS_OFFSET is set to 1.5M to give us more space for FDTs.
* RB2 gets a work-around to fix the USB dr_mode property before booting Linux.
Add support for driving the GPIO pins as output low or high.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
SE HMIBSC board uses UART1 as the main debug console, so add
corresponding clocks and pinmux support. Along with that update
instructions to enable clocks for debug UART support.
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Currently, IPQ4019 pinctrl driver supports only a very limited number of
pin functions and is not fully DT compatible with Linux pinctrl nodes.
IPQ40xx SoC-s sometimes use different pin function numbers for the same
function depending on the pin number, so for example I2C0 on GPIO58 uses
function number 3 while on GPIO59 it uses function number 2.
So, in order to make the driver compatible with upstream DTS to avoid the
need to patch the pinctrl nodes in U-Boot and support all of the missing
pin functions lets rework the driver based on upstream Linux IPQ4019
pinctrl driver and the pending SM8150 U-Boot pinctrl driver which also uses
different function numbers pased on the exact pin number.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
If compiled with logging and debug UART support, the following is printed:
serial_msm serial@78af000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
This is due to the fact that IPQ4019 pinctrl driver is not available prior
to relocation and thus MSM serial will fail probing as pinctrl provider is
not available.
So, lets enable DM_FLAG_PRE_RELOC for IPQ4019 pinctrl to fix this.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
We want to use OF_UPSTREAM on IPQ40XX as its well supported upstream, so
as a preparation update pinctrl driver to look for the upstream pin format.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
IPQ4019 pinctrl driver was moved to the dedicated Qualcomm pinctrl
directory, but the KConfig depends on ARCH_SNAPDRAGON only and thus
PINCTRL_QCOM_IPQ4019 cannot be selected when ARCH_IPQ40XX is used.
Fixes: 24d2908e987a ("pinctrl: qcom: move ipq4019 driver from mach-ipq40xx")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Adjust sdm845_get_pin_name() to return the correct names for the special
pins. This fixes a non-fatal -ENOSYS error when probing MMC.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
This SoC features a pinctrl block with north, south, and west tiles
accessible to the AP.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
This SoC features a pinctrl block with west, east, and south tiles.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
This SoC has a basic pinctrl block with no tiles.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Add pinctrl driver for the TLMM block found in the SM8650 SoC.
This driver only handles the gpio and qup2_se7 pinmux, and makes sure
the pinconf applies on SDC2 pins.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Add pinctrl driver for the TLMM block found in the SM8550 SoC.
This driver only handles the gpio and qup1_se7 pinmux, and makes sure
the pinconf applies on SDC2 pins.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
This patch is the preparation for SM8150 support. This new SoC
depending on the particular pin can have different numbers for the
same function. For example "rgmii" function for GPIO4 has id=2 while
for GPIO59 it has id=1. So, to support this type of SoCs,
get_function_mux() callback needs to know for which pin the function
is requested.
Signed-off-by: Volodymyr Babchuk <volodymyr_babchuk@epam.com>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Use the root compatible strings from upstream Linux, add missing
'#clock-cells' property to the gcc node.
Adjust some of the msm8916/apq8016 drivers to use the correct upstream
compatible properties and DT bindings.
This prepares us to switch to upstream DT in a future patch.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
On the DB410c we support running as a first stage bootloader. This
requires initialising the GPIOs which are muxed to UART before they can
be used. Add DM_FLAG_PRE_RELOC to the apq8016 pinctrl driver to ensure
that we do this early enough.
This is required to prevent the first few lines of UART log from being
dropped.
Reported-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Upstream devicetrees label GPIOs with "gpioX", not "GPIO_X", fix this
for SoCs where we're now using upstream DT.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Most platforms have a handful of "special" GPIOs, like the MMC
clock/data lanes, UFS reset, etc. These don't follow the usual naming
scheme of "gpioX" and also have unique capabilities and registers. We
can get away without supporting them all for now, but DT compatibility
is still an issue.
Add support for allowing these to be specified after the other pins, and
make all pinmux/pinconf calls for them nop.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The pinctrl and GPIO drivers are currently heavily incompatible with
upstream. Most Qualcomm pinctrl blocks feature "tiles" of pins, each at
it's own address. Introduce support for these by allowing the soc driver
to specify per-pin register offsets similarly to the Linux driver.
Adjust the GPIO driver to handle these too, and finally enable support
for all pins with the same numbering as used in Linux.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Drop the duplicated pinctrl-snapdragon driver from mach-ipq40xx and add
it to drivers/pinctrl/qcom.
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Move the Qualcomm pinctrl drivers out of mach-snapdragon and over to the
rest of the pinctrl drivers, adjust the drivers so that support for each
platform can be enabled/disabled individually and introduce platform
specific configuration options.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
