MD Danish Anwar <danishanwar@ti.com> says:
Introduce ICSSG PRUETH support in uboot. The ICSSG driver is used in TI
AM654 SR2.0.
The ICSSG PRU Sub-system runs on EMAC firmware. This series Introduces
support for ICSSG driver in uboot.
This series has been tested on AM65x SR2.0, and the ICSSG interface is
able to ping / dhcp and boot kernel using tftp in uboot.
To use ICSSG2 ethernet, the ICSSG firmware needs to be loaded to PRU RPROC
cores and RPROC cores need to be booted with the firmware. This step is
done inside driver similar to kernel.
The remoteproc driver uses request_fw_into_buf() API from fs-loader driver
to load and start rproc with the required firmwares.
This series only introduces driver files. The device tree and config
changes to enable ICSSG driver will be introduced later.
ICSSG firmware supports FDB commands. Add support to send FDB commands
from driver. Once rx_flow_id is obtained from dma, let firmware know that
we are using this rx_flow_id by sending a FDB command.
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
This is the PRUSS Ethernet driver for TI AM654 SR2.0 and later SoCs with
the ICSSG PRU Sub-system running EMAC firmware. ICSSG Subsystem supports
two slices per instance. This driver caters to both slices / ports of
the icssg subsystem.
Since it is not possible for Ethernet driver to register more than one
port for a given instance, this patch introduces top level PRUETH as
UCLASS_MISC and binds UCLASS_ETH to individual ports in order to support
bringing up more than one Ethernet interface in U-Boot.
Since top level driver is UCLASS_MISC, board files would need to
instantiate the driver explicitly.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Add icssg_queue.c file. This file introduces macros and APIs related to
ICSSG queues. These will be used by ICSSG Ethernet driver.
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Add icssg_config.h / .c and icssg_classifier.c files. These are firmware
configuration and classification related files. Add MII helper APIs and
MACROs. These APIs and MACROs will be later used by ICSSG Ethernet driver.
Also introduce icssg_prueth.h which has definition of prueth related
structures.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Add firmware interface related headers and macros for ICSSG Ethernet
driver. These macros will be later used by the ICSSG ethernet driver.
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
The device name is a concatenation of the device node name of the cpsw
device and of the device node name of the port. In my case that is
ethernet@8000000
port@1
First the buffer is really too small, but more importantly, there is no
boundary check. Use snprintf() and increase the buffer size.
Fixes: 38922b1f4acc ("net: ti: am65-cpsw: Add support for multi port independent MAC mode")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Add a new Kconfig symbol MDIO_TI_CPSW for the CPSW MDIO
driver and build it with proper DM support if enabled.
If MDIO_TI_CPSW is not enabled then we continue to
behave like before.
Clean up MDIO custom handling in am65-cpsw and use
dm_eth_phy_connect() to get the PHY.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Tested-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
This old patch was marked as deferred. Bring it back to life, to continue
towards the removal of common.h
Move this out of the common header and include it only where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enhance the AM65 CPSW NUSS driver to perform a MDIO reset using a GPIO
line. Logic is also added to perform a pre and post delay around reset
using the optional 'reset-delay-us' and 'reset-post-delay-us' properties.
This is similar to the reset being performed in the Linux kernel. The
reset is done once when the CPSW MDIO bus is being initialized.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Approved DT binding has the port mode register in the
"phys" property. Get it from there instead of the custom
"cpsw-phy-sel" property.
This will allow us to keep DT in sync with Linux.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Nishanth Menon <nm@ti.com>
The approved DT property for MAC efuse (ROM) address is
"ti,syscon-efuse".
Use that and drop custom property "mac_efuse".
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Nishanth Menon <nm@ti.com>
The binding represents the MDIO controller as a child device tree
node of the MAC device tree node.
The U-Boot driver mostly ignores that child device tree node and just
hardcodes the resources it uses to support both the MAC and MDIO in a
single driver.
However, some resources like pinctrl muxing states are thus ignored.
This has been a problem with some device trees that will put some
pinctrl states on the MDIO device tree node, like the SK-AM62 Device
Tree does.
Let's rework the driver a bit to create a dummy MDIO driver that we will
then get during our initialization to force the core to select the right
muxing.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Nishanth Menon <nm@ti.com>
The different CPSW sub-system Ethernet ports have different PHY mode
control registers. In order to allow the modes to get configured
independently only the register for the port in question must be
accessed, otherwise we would just be re-configuring the mode for port 1,
while leaving all others at their power-on defaults. Fix this issue by
adding a port-number based offset to the mode control base register
address based on the fact that the control registers for the different
ports are spaced exactly 0x4 bytes apart.
Fixes: 9d0dca1199d1 ("net: ethernet: ti: Introduce am654 gigabit eth switch subsystem driver")
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
This platform is currently unmaintained and untested, so remove it.
Further, as it is the only TI816X SoC example, remove related files as
well.
Signed-off-by: Tom Rini <trini@konsulko.com>
At this point, the remaining places where we have a symbol that is
defined as CONFIG_... are in fairly odd locations. While as much dead
code has been removed as possible, some of these locations are simply
less obvious at first. In other cases, this code is used, but was
defined in such a way as to have been missed by earlier checks. Perform
a rename of all such remaining symbols to be CFG_... rather than
CONFIG_...
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When the ti814x_evm config was removed most, but not all, of the
relevant support code was remove. Get rid of what was missed.
Fixes: 50b532686849 ("ti814x: Remove platform")
Signed-off-by: Tom Rini <trini@konsulko.com>
For the TI SoCs affected by errata i2329, enable MDIO manual
mode by default
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
In certain TI SoCs, on the CPSW and ICSS peripherals, there is
a possibility that the MDIO interface returns corrupt data on
MDIO reads or writes incorrect data on MDIO writes. There is also
a possibility for the MDIO interface to become unavailable until
the next peripheral reset.
The workaround is to configure the MDIO in manual mode and disable the
MDIO state machine and emulate the MDIO protocol by reading and writing
appropriate fields in MDIO_MANUAL_IF_REG register of the MDIO controller
to manipulate the MDIO clock and data pins.
More details about the errata i2329 and the workaround is available in:
https://www.ti.com/lit/er/sprz487a/sprz487a.pdf
Add implementation to disable MDIO state machine, configure MDIO in manual
mode and provide software MDIO read and writes via MDIO bitbanging. Allow
the MDIO to be initialized based on the need for manual mode.
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Change type of private struct member mdio_base from void * to
phys_addr_t. This allows us to drop 2 casts.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Rename constant PHY_INTERFACE_MODE_NONE to PHY_INTERFACE_MODE_NA to make
it compatible with Linux' naming.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Add helpers ofnode_read_phy_mode() and dev_read_phy_mode() to parse the
"phy-mode" / "phy-connection-type" property. Add corresponding UT test.
Use them treewide.
This allows us to inline the phy_get_interface_by_name() into
ofnode_read_phy_mode(), since the former is not used anymore.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
In case fastboot over Ethernet, am65_cpsw_stop() is not called unless
DM_FLAG_OS_PREPARE is set. Without call to am65_cpsw_stop(), DMA
resources are not released thus leading to failures in kernel.
Fix this by adding DM_FLAG_OS_PREPARE flag to am65_cpsw_nuss_port
driver.
Reported-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
On certain TI SoC, like AM64x there is a CPSW3G which supports 2
external independent MAC ports for single CPSW instance.
It is not possible for Ethernet driver to register more than one port
for given instance.
This patch modifies top level CPSW NUSS as UCLASS_MISC and binds
UCLASS_ETH to individual ports so as to support bring up more than one
Ethernet interface in U-Boot.
Note that there is no isolation in the since, CPSW NUSS is in promisc
mode and forwards all packets to host.
Since top level driver is now UCLASS_MISC, board files would need to
instantiate this driver explicitly.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Currently driver may end up caching disabled port ID as active
interface. Fix this by bailing out earlier in case port is marked
disabled in the DT.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
CPSW NUSS IP on K3 SoCs can have more than one external port (upto 8)
Therefore increase AM65_CPSW_CPSWNU_MAX_PORTS to 9 (8 ext + 1 Root port)
as preparation to allow any one of the 8 ports to be used as ethernet
interface in U-Boot.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
Without DM_ETH, cpsw_priv.dev is an eth_device. Just use its name instead.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
