The 'rng list' command probes all RNG devices and list those devices
that are successfully probed. Also update the help info.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Weizhao Ouyang <o451686892@gmail.com>
This migrates the plaintext README in
board/theobroma-systems/ringneck_px30 to doc/board/theobroma-systems and
while doing so, update the instructions and rewrite it in rST.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
This migrates the plaintext README in
board/theobroma-systems/puma_rk3399 to doc/board/theobroma-systems and
while doing so, update the instructions and rewrite it in rST.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
When copying the build system for Linux we missed to replace some
instances of 'Documentation' by 'doc'.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Python 3.6 introduced a DeprecationWarning for invalid escape sequences.
This is upgraded to a SyntaxWarning in Python 3.12, and will eventually
be a syntax error.
Fix these now to get ahead of it before it's an error.
Signed-off-by: Benjamin Gray <bgray@linux.ibm.com>
Message-ID: <20230912060801.95533-3-bgray@linux.ibm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Adapted for U-Boot
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Use proper binary artifact names for HSFS devices.
Do not use the *_unsigned binaries.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
When using the previous prototype you got a compiler warning like this:
warning: initialization of 'int (*)(struct cmd_tbl *, int, int, char * const*)' from incompatible pointer type 'int (*)(struct cmd_tbl *, int, int, const char **)' [-Wincompatible-pointer-types]
Fixes: 3d9640f55cb2 ("doc: expand README.commands")
Signed-off-by: Alexander Dahl <ada@thorsis.com>
TI K3 J784S4 and AM69 are new additions to the K3 SoC family.
Add documentation about the J784S4 EVM and AM69 SK.
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # AM69-SK
The "bootflow" command currently doesn't support scanning a single
partition. This is inconvenient in setups with multiple bootable
partitions within a single disk, but only one is desired.
Support scanning a single disk partition. Specifically, support the
syntax:
bootflow scan mmc1:4
which scans only mmc device 1, partition 4.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Use the latest, mx93a1-ahab-container.img that is compatible with the
i.MX93 A1 revision.
Using mx93a1-ahab-container.img on an A0 chip and conversely causes a boot
failure without any traces on the UART.
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Marek Vasut <marek.vasut+renesas@mailbox.org> says:
Rename R-Mobile to Renesas all over the place because the chips are
made by Renesas, while only a subset of them is from the R-Mobile line.
Add new renesas entry and update rmobile entry to match.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
In gsub, when the destination string is empty, the string 't' is
provided and the regular expression doesn't match, then the final result
is an empty string.
Example:
=> echo ${foo}
=> setenv foo
=> setexpr foo gsub e a bar
=> echo ${foo}
=>
The variable ${foo} should contain "bar" and the lack of match shouldn't
be considered an error.
This patch fixes the erroneous behavior by removing the return
statement and breaking out of the loop in case of lack of match.
Also add a test for the no match case.
Signed-off-by: Massimiliano Minella <massimiliano.minella@se.com>
Currently, if boot with extlinux.conf and do not set the fdt
U-Boot will provide its own device tree. This behavior is
beneficial if the U-Boot device tree is in sync with Linux,
but it totally halts the booting of pre-dtb kernels (3.4 for
example) since it uses ATAGs. To fix this, pass `-` in the
fdt extlinux field as a signal that no tree should be used.
Suggested-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Tested-by: Jethro Bull <jethrob@hotmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The MSM8916/APQ8016 Technical Reference Manual is publicly available and
contains a lot of useful register maps for many core parts of the SoC.
Include an archive.org link to it in the dragonboard410c documentation.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Replace the board specific docs with a generic board.rst file which
documents the build/boot process for the sdm845 and qcs404 boards now
that the only differences are the DTB in use.
At the same time, create a debugging page to document some useful
snippets and tips for working with Qualcomm platforms.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Use the root compatible strings from upstream Linux, add missing
'#clock-cells' property to the gcc node.
Adjust some of the msm8916/apq8016 drivers to use the correct upstream
compatible properties and DT bindings.
This prepares us to switch to upstream DT in a future patch.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The upstream DT is supported here, so drop the U-Boot specific binding
docs.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Encourage SoC/board maintainers to migrate to using devicetree-rebasing
subtree and maintain a regular sync with Linux kernel devicetree files
and bindings.
Along with that add documentation regarding how to run DT bindings
schema checks.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
With the relatively new button API in U-Boot, it's now much easier to
model the common usecase of mapping arbitrary actions to different
buttons during boot - for example entering fastboot mode, setting some
additional kernel cmdline arguments, or booting with a custom recovery
ramdisk, to name a few.
Historically, this functionality has been implemented in board code,
making it fixed for a given U-Boot binary and requiring the code be
duplicated and modified for every board.
Implement a generic abstraction to run an arbitrary command during boot
when a specific button is pressed. The button -> command mapping is
configured via environment variables with the following format:
button_cmd_N_name=<button label>
button_cmd_N=<command to run>
Where N is the mapping number starting from 0. For example:
button_cmd_0_name=vol_down
button_cmd_0=fastboot usb 0
This will cause the device to enter fastboot mode if volume down is held
during boot.
After we enter the cli loop the button commands are no longer valid,
this allows the buttons to additionally be used for navigating a boot
menu.
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Tegra30
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Rework the section about includes slightly. We should not be using
common.h anywhere, so remove that from examples and ask people to send
patches removing it when found. Doing this also means we need to reword
other parts of this section. Be clearer about using alphabetical
ordering.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Sonoff iHost is gateway device designed to provide a Smart Home Hub,
it is based on Rockchip RV1126. There is also a version with 2GB RAM
based off the RV1109 dual core SoC however this works with the same
config as the RV1126 for uboot purposes.
Features:
- Rockchip RV1126
- 4GB DDR4
- 8GB eMMC
- microSD slot
- RMII Ethernet PHY
- 1x USB 2.0 Host
- 1x USB 2.0 OTG
- Realtek RTL8723DS WiFi/BT
- EFR32MG21 Silabs Zigbee radio
- Speaker/Microphone
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add document for Milk-V Duo board which based on Sophgo's CV1800B SoC.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add documentation to introduce the Falcon Mode on RISC-V.
In this mode, the boot sequence is SPL -> OpenSBI -> Linux kernel.
Signed-off-by: Randolph <randolph@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Documentation:
* uefi: remove ".py" suffix for pytest.py command
* correct date in migration plan for CONFIG_DM
UEFI:
* fix conflicting SPDX license in RISC-V EFI linker scripts
* page align EFI binary section in RISC-V EFI binaries
* separate .data and .text sections of RISC-V EFI binaries
* use common function to get EFI configuration table
-----BEGIN PGP SIGNATURE-----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=ZGn5
-----END PGP SIGNATURE-----
Merge tag 'efi-2024-04-rc1-4' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request efi-2024-04-rc1-4
Documentation:
* uefi: remove ".py" suffix for pytest.py command
* correct date in migration plan for CONFIG_DM
UEFI:
* fix conflicting SPDX license in RISC-V EFI linker scripts
* page align EFI binary section in RISC-V EFI binaries
* separate .data and .text sections of RISC-V EFI binaries
* use common function to get EFI configuration table
Devarsh Thakkar <devarsht@ti.com> says:
Move video memory reservation for SPL at end of RAM so that it does
not interefere with reservations for next stage so that the next stage
need not have holes in between for passed regions and instead it can
maintain continuity in reservations.
Also catch the bloblist before starting reservations to avoid the same
problem.
While at it, also fill missing fields in video handoff struct before
passing it to next stage.
This is as per discussions at :
For moving SPL framebuffer reservation at end of RAM:
https://lore.kernel.org/all/CAPnjgZ3xSoe_G3yrqwuAvoiVjUfZ+YQgkOR0ZTVXGT9VK8TwJg@mail.gmail.com/
For filling missing video handoff fields :
https://lore.kernel.org/all/CAPnjgZ1Hs0rNf0JDirp6YPsOQ5=QqQSP9g9qRwLoOASUV8a4cw@mail.gmail.com/
Add details regarding scheme which need to be followed in SPL and
further stages for those regions which need to be preserved across
bootstages.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium>
Add info regarding splash screen, video, bloblist and GPIO related
Kconfigs which were missing in the documentation.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium>
the file pytest.py does not exist
Signed-off-by: Wei Ming Chen <jj251510319013@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
That's most probably a typo, because driver model design documents seem
to be from 2012 and there is no 2010.01 release.
Fixes: 282ed24fb3ca ("dm: MIGRATION: Add migration plan for CONFIG_DM")
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Provide a man-page for the smbios command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add support for WinLink E850-96 board [1]. It's based on Exynos850 SoC
and follows 96boards specification, so it's compatible with 96boards
mezzanine boards [2]. This patch enables next features:
* Serial console
* USI
* PMU (muxing AP UART path)
* Pinctrl
* Clocks
* Timer (ARMv8 architected)
* Reset control
It's quite a minimal enablement. Features like MMC, USB and Ethernet
will be enabled later.
The rationale for config values is as follows:
* TEXT_BASE = 0xf8800000
That's where BL2 loads the U-Boot payload, so TEXT_BASE must be
exactly this value. Overall the memory map is designed in a way to
keep the bootloader in the upper 128 MiB area of RAM, which is
0xf8000000..0xffffffff. That includes bootloader's code, stack,
data, heap, MMU tables, etc. All the memory below that 128 MiB chunk
can be used for storing boot images (0x80000000..0xf8000000).
* CUSTOM_SYS_INIT_SP_ADDR = 0xf8c00000
Just 4 MiB above the TEXT_BASE address, to leave enough space for
U-Boot code and stack itself (grows downwards).
* SYS_LOAD_ADDR = 0x80000000
The beginning of RAM. That's where Linux kernel image must be
loaded.
* SYS_MALLOC_LEN = 0x81f000
8 MiB for malloc() + ENV_SIZE (128 KiB)
* SYS_MALLOC_F_LEN = 0x4000
Increase malloc() pool size available before relocation from 8 KiB
(default) to 16 KiB. Otherwise "alloc space exhausted" message
appears in U-Boot log during board_init_f() stage. There are next
reasons for doing so:
1. Having "bootph-all" flags in some dts nodes leads to binding
those during pre-relocation stage, and binding (DM) uses
dynamic memory allocation
2. clk-exynos850 driver uses CCF clocks, which in turn use dynamic
memory allocation
Device tree file was imported from Linux kernel. All nodes and boot
phase flags added in exynos850-e850-96-u-boot.dtsi are only needed to
enable serial console:
* oscclk -> cmu_top -> cmu_peri: generate UART/USI clocks
* pinctrl_alive and uart1_pins: needed to mux UART pins
* pmu_system_controller: configures AP UART path to uart1_pins
* usi_uart: configures USI block to operate as a UART protocol
* serial_0: enables serial console (UART)
[1] https://www.96boards.org/product/e850-96b/
[2] https://www.96boards.org/products/mezzanine/
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add bindings documentation and the header file for Exynos850 clock
controller. It was taken from Linux kernel [1,2].
[1] Documentation/devicetree/bindings/clock/samsung,exynos850-clock.yaml
[2] include/dt-bindings/clock/exynos850.h
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
