The vop node should not be included in TPL/SPL control FDT, it should
only be included at U-Boot proper pre-reloc phase.
Change to use bootph-some-ram prop to fix this.
Fixes: 6794063d5065 ("ARM: dts: rk3328: Enable VOP for bootph-all")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Model: Firefly roc-rk3328-cc
DRAM: 1 GiB (effective 1022 MiB)
Video device 'vop@ff370000' cannot allocate frame buffer memory -ensure the device is set up before relocation
Error binding driver 'rockchip_rk3328_vop': -28
Some drivers failed to bind
initcall sequence 000000003ffcd5e8 failed at call 000000000021a5c4 (err=-28)
### ERROR ### Please RESET the board ###
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
USB gadget is not working fully as expected on RK3328, it uses a
board_usb_init() function to initialize the DWC2 OTG port.
The board_usb_init() function does not intgrate with the generic phy
framework and as a result the USB phy is not properly configured before
or after USB gadget use.
Having both USB_DWC2 and DWC2_OTG enabled for the same board is also
causing some issues.
Trying to use rockusb or ums command after usb stop result in a freeze
due to usb stop is putting the phy in a suspended state.
=> usb start
=> usb stop
=> ums 0 mmc 0
--> freeze due to usb phy is suspended <--
Fix this by only using one of USB_DWC2 (host) or DWC2_OTG (peripheral)
depending on the most likely usage of the otg port and by migrating to
use DM_USB_GADGET instead of a board_usb_init() function.
The nanopi-r2 and orangepi-r1-plus variants share OTG and power using a
Type-C connector, mark these boards dr_mode as peripheral, the most
likely usage is for recovery and image download.
The rock64 and roc-cc currently use dr_mode as host, remove the DWC2_OTG
driver from these boards to ensure that the USB_DWC2 driver is used.
The rock-pi-e board does not enable the usb20_otg node so both USB_DWC2
and DWC2_OTG is removed from this board.
Enable RockUSB and UMS on all boards with a otg port in peripheral mode.
Also with the migration to DM_USB_GADGET completed the U-Boot specific
change to reorder usb nodes in the soc device tree can be reverted.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Similar to RK35xx the BootRom in RK3328 can read all data and look for
idbloader at 0x8000, same as it does for SD and eMMC.
Use the rksd format and modify the mkimage offset to generate a bootable
u-boot-rockchip-spi.bin that can be written to 0x0 of SPI NOR flash.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Replace the rockchip,cryptov1-rng compatible with compatibles used in
the linux device tree for RK3288, RK3328 and RK3399 to ease sync of SoC
device tree from linux.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When RK3328 boards run SPL from eMMC and fail to load FIT from eMMC due
to it being missing or checksum validation fails there is a fallback to
read FIT from SD-card. However, without proper pinctrl configuration
reading FIT from SD-card will fail:
U-Boot SPL 2024.04-rc1 (Feb 05 2024 - 22:18:22 +0000)
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Fix this by tagging related emmc and sdmmc pinctrl nodes with bootph
props. Also sort and move common nodes shared by all boards to the SoC
u-boot.dtsi.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Change to use a common FIT load order, same-as-spl > SD-card > eMMC on
RK3328 boards. Only EVB and Radxa ROCK Pi E is affected by this change.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the rk3328 rng details to the u-boot.dtsi and
enable the RNG on the Rock64 to be able to provide
a random seed via UEFI.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
(Fix typo message)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
rk3328-xhci has been added due to the fact that the upstream
dwc3 is unsupported. Moreover, the driver for rk3328-xhci is
not added to the code tree.
By considering these facts and unsupported rk3328-xhci this
patch is dropping all related code from DT. However, the DWC3
is fixed now in dwc3-generic and RK3328 USB 3.0 is functional
in upcoming patches.
Let's drop it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This allows to build u-boot-rockchip.bin binary with binman for Rockchip
ARM64 boards instead of the legacy Makefile way.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add U-Boot SPI support for the RK3328
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(fix checkpatch error for code ident)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The "hnp-srp-disable" property for dwc2 is specific to U-boot, not part
of upstream Linux's device tree bindings.
Move it to rk3328-u-boot.dtsi to avoid losing it when syncing device
tree files.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
