In Linux, we allow sleep moci to be turned off when the carrier board
supports it and the system is in suspend. In U-Boot, however, we want
the sleep moci to be always on. So we use a gpio hog and disable the
regulator. This change is necessary because we switched to upstream
device tree files with commit 23fe2def1edf
("verdin-imx8mm/verdin-imx8mp: move imx verdins to OF_UPSTREAM"). A
recent upstream patch removes the gpio hog from the Linux device tree,
so we need to add it to the u-boot dtsi. The following patch will remove
the gpio hog from the Linux device tree:
https://lore.kernel.org/linux-devicetree/20240405160720.5977-1-eichest@gmail.com/
The U-Boot patch can be applied without it and will not break the build.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
This commit introduces support for the Toradex sysinfo driver in U-Boot,
which uses information from Toradex config block to print correct
board model.
In case the Toradex config block is not present sysinfo prints the model
of the board provided by device tree removing per board specific prints.
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # Verdin iMX8M Plus
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Move the crypto and sec_jr* nodes from board-specific
u-boot.dtsi files into the common files. Additionally protect the
nodes with ifdef CONFIG_FSL_CAAM as they don't serve any purpose if
that is not enabled.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Move the firmware/optee node to the common imx8mp-u-boot.dtsi and
protect it with an ifdef CONFIG_OPTEE as it is a meaningless node
without the optee driver enabled.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Drive CTRL_SLEEP_MOCI# high at boot (SPL) using a GPIO hog, this signal
may be used to control some power-rails on the carrier board, therefore
it should be set to high when the module is booting.
To do this as early as possible is generally a good idea and the issue
was noticed on the Yavia carrier board where it is needed to power the
I2C EEPROM on the carrier board.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The assigned-clock no longer have to be dropped, the clock are now
defined in clk-imx8mp.c and used by DWMAC driver to configure the
DWMAC clock. Drop the workarounds from U-Boot specific DT extras.
Signed-off-by: Marek Vasut <marex@denx.de>
Synchronise device tree with linux v5.19-rc5.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device tree we are now using the
regular one for the Verdin Development (carrier) board (e.g.
imx8mp-verdin-wifi-dev.dtb rather than the previous imx8mp-verdin.dtb).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
