Agilex5 FSBL is required to disable the power of unused peripheral SRAM
blocks to reduce power consumption.
Introducing a new power manager driver for Agilex5 which will be called
as part of Agilex5 SPL initialization process.
This driver will read the peripheral handoff data obtained from the
bitstream and will power off the specified peripheral's SRAM from the
handoff data values.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
In case of the i.MX8M power-domains (i.MX8MQ, MM, MN) there is only
one power-domain for each device. Therefore the 'id' field in struct
power_domain should always be zero.
Currently if a power-domain is accessed after the initial bind, the
'id' field is left uninitialized. This didn't cause any problems
until the following commits were introduced:
9086b64ca071 ("power-domain: Add support for refcounting (again)")
a785ef24487b ("imx: power-domain: Enable refcounting on imx8mp")
Now the 'id' field gets accessed in the power_domain_off() sequence
and the invalid value causes "Synchronous Abort" failures.
This was observed on a i.MX8MM board when running "usb start" and
then "usb stop".
Fix this issue by setting power_domain->id to '0' in
imx8m_power_domain_of_xlate().
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Fixes: d08a194871fd ("imx: add support for i.MX8MQ power domain controller")
Fixes: 9086b64ca071 ("power-domain: Add support for refcounting (again)")
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
If there is a SoC specific SCMI protocol driver, using
scmi_proto_driver_get() function can avoid to add SoC specific code to
scmi_agent-uclass.c.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Prevent enabling/disabling multiple times the same power domain to avoid
breakages due to the same power domains being referenced several times
by different device nodes.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It is very surprising that such an uclass, specifically designed to
handle resources that may be shared by different devices, is not keeping
the count of the number of times a power domain has been
enabled/disabled to avoid shutting it down unexpectedly or disabling it
several times.
Doing this causes troubles on eg. i.MX8MP because disabling power
domains can be done in recursive loops were the same power domain
disabled up to 4 times in a row. PGCs seem to have tight FSM internal
timings to respect and it is easy to produce a race condition that puts
the power domains in an unstable state, leading to ADB400 errors and
later crashes in Linux.
Some drivers implement their own mechanism for that, but it is probably
best to add this feature in the uclass and share the common code across
drivers. In order to avoid breaking existing drivers, refcounting is
only enabled if the number of subdomains a device node supports is
explicitly set in the probe function. ->xlate() callbacks will return
the power domain ID which is then being used as the array index to reach
the correct refcounter.
As we do not want to break existing users while stile getting
interesting error codes, the implementation is split between:
- a low-level helper reporting error codes if the requested transition
could not be operated,
- a higher-level helper ignoring the "non error" codes, like EALREADY and
EBUSY.
CI tests using power domains are slightly updated to make sure the count
of on/off calls is even and the results match what we *now* expect. They
are also extended to test the low-level functions.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tom Rini <trini@konsulko.com> says:
This series switches to always using $(PHASE_) in Makefiles when
building rather than $(PHASE_) or $(XPL_). It also starts on documenting
this part of the build, but as a follow-up we need to rename
doc/develop/spl.rst and expand on explaining things a bit.
Link: https://lore.kernel.org/r/20250401225851.1125678-1-trini@konsulko.com
It is confusing to have both "$(PHASE_)" and "$(XPL_)" be used in our
Makefiles as part of the macros to determine when to do something in our
Makefiles based on what phase of the build we are in. For consistency,
bring this down to a single macro and use "$(PHASE_)" only.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support for the i.MX8 MEDIAMIX domain which is driving the power
over the whole display/rendering pipeline.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
It is very surprising that such an uclass, specifically designed to
handle resources that may be shared by different devices, is not keeping
the count of the number of times a power domain has been
enabled/disabled to avoid shutting it down unexpectedly or disabling it
several times.
Doing this causes troubles on eg. i.MX8MP because disabling power
domains can be done in recursive loops were the same power domain
disabled up to 4 times in a row. PGCs seem to have tight FSM internal
timings to respect and it is easy to produce a race condition that puts
the power domains in an unstable state, leading to ADB400 errors and
later crashes in Linux.
CI tests using power domains are slightly updated to make sure the count
of on/off calls is even and the results match what we *now* expect.
As we do not want to break existing users while stile getting
interesting error codes, the implementation is split between:
- a low-level helper reporting error codes if the requested transition
could not be operated,
- a higher-level helper ignoring the "non error" codes, like EALREADY and
EBUSY.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently in j721e_init.c we check which firewalls to remove using
the board configuration (e.g CONFIG_TARGET_J721E_R5_EVM). We do this
as J721e and J7200 have different IP and firewalls but use the same
SoC definition (SOC_K3_J721E) even though they are different SoCs.
The idea was they would be similar enough that they both could use
the same SoC config to help with common code sharing. Board checks
would then be used differentiate.
This has grown far too messy to maintain any more, especially now
that there is more than one board using J721e (EVM, SK, Beagle AI64).
As differentiation is done based on board, every one of these boards
would have to have checks added for them. Instead let's split J7200
support out from J721e like how normal new SoC support is done.
This patch touches several subsystems and could not be split much better
as when we add SOC_K3_J7200 we want to make use of it in all spots that
once used the combined SOC_K3_J721E so we can turn off SOC_K3_J721E when
building for J7200 boards.
Signed-off-by: Andrew Davis <afd@ti.com>
Re-use j784s4 clocks and power domains for j742s2 family of device.
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Convert to using livetree API functions.
Without this if livetree is enabled (OF_LIVE) the imx8m-power-domain
driver will (silently) fail to probe its children leaving you with
no power domain support causing issues with certain devices.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The upstream Device Tree for GXBB/GXL/G12A was updated with VPU domain
shared between the VPU and HDMI node, causing a double enable.
Simply store the enable state and avoid enabling twice, fixing
HDMI output on all platforms.
Link: https://lore.kernel.org/r/20241009-u-boot-topic-fix-hdmi-v1-2-2479cd90c4ea@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Include the clock and lpsc tree files needed for the wkup spl to
initialize the proper PLLs and power domains to boot the SoC.
Reviewed-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Add the power domain platform data entries in alphabetical order.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Expose the high performance PLL as clock framework clock, so the
PCIe PHY can use it when there is no external refclock provided.
Inspired from counterpart Linux kernel v6.8-rc3 driver:
drivers/pmdomain/imx/imx8mp-blk-ctrl.c. Use last Linux kernel driver
reference commit 7476ddfd36ac ("pmdomain: imx8mp-blk-ctrl: Convert to
platform remove callback returning void").
Tested-by: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice*
Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon-kit
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Add support for GPCv2 power domains and clock handling for PCIe and
PCIe PHY.
Tested-by: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice*
Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon-kit
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Include the clock and lpsc tree files needed for the wkup spl to
initialize the proper PLLs and power domains to boot the SoC.
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Cleanup this list and standardize on using the IS_ENABLED macro for the
power domain data list.
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Add clk and device data which can be used by respective drivers
to configure clocks and PSC.
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # AM69-SK
In the imx8m power domain kernel driver, there is an extra udelay(5)
prior to requesting the domain to power up:
https://github.com/torvalds/linux/blob/v6.3/drivers/soc/imx/gpcv2.c#L347-L375
Haven't observed any issues due to the lack of this delay in U-Boot yet,
but better to align it with the kernel driver implementation.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
This patch adds Power controller driver support for Amlogic
A1 family using secure monitor calls. The power domains register
only can access in secure world.
Signed-off-by: Alexey Romanov <avromanov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230531093156.29240-4-avromanov@sberdevices.ru
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Move imx8 sci header file to include/firmware/imx, then we could
use build macro to reuse some i.MX8 drivers for i.MX9, such as
drivers/cpu/imx8_cpu.c.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Introduce the auto-generated clock tree and power domain data needed to
attach the am62a into the power-domain and clock frameworks of uboot
Signed-off-by: Bryan Brattlof <bb@ti.com>
Introduce autogenerated SoC data support clk and device data for the
AM62. Hook it upto to power-domain and clk frameworks of U-Boot.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
If dev_count_phandle_with_args returns 0 or another error, then pd will never
have been initialized by power_domain_get_by_index. Avoid comparing against
pd.dev in this situation.
Fixes: 3e4fcfa4bc ("power-domain: fix hang in endless loop on i.MX8")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add trivial driver for i.MX8MP HSIOMIX handling. This is responsible
for enabling the GPCv2 power domains and clock for USB 3.0 and PCIe
in the correct order. Currently supported is the USB 3.0 part which
can be tested, PCIe support should be easy to add.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add i.MX8MP power domain handling into the driver. This is based on the
Linux GPCv2 driver state which is soon to be in Linux next.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Implement power_domain_get_by_name() convenience function which parses
DT property 'power-domain-names' and looks up power domain by matching
name.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Simon Glass <sjg@chromium.org>
This driver is the only SMCCC dependency in iMX8M U-Boot port. Rework
the driver based on Linux GPCv2 driver to directly control the GPCv2
block instead of using SMCCC calls. This way, U-Boot can operate the
i.MX8M power domains without depending on anything else.
This is losely based on Linux GPCv2 driver. The GPU, VPU, MIPI power
domains are not supported to save space, since they are not useful in
the bootloader. The only domains kept are ones for HSIO, PCIe, USB.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-defconfig
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The arch/arm/include/asm/arch-imx8m/power-domain.h is not included
anywhere except in drivers/power/domain/imx8m-power-domain.c, just
inline the content and drop the header. No functional change.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-defconfig
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
In case the power domain node structure is gpc@303a0000/pgc/power-domain@N,
do not bind power domain driver to the 'pgc' node, but rather descend into
it and only bind power domain drivers to power-domain@N subnodes. This way
we do not waste one useless driver instance associated with 'pgc' node.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-defconfig
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
In case the ops is not implemented, return 0 in the core right away.
This is better than having multiple copies of functions which just
return 0 in each power domain driver. Drop all those empty functions.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Simon Glass <sjg@chromium.org>
It is possible for power domain IDs to be great than 31. If this
happens, the PTCMD and PTSTAT registers must overflow into adjacent
corresponding PTCMD_H and PTSTAT_H registers for each. Update the driver
to account for this.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Remove private xpm_configobject[] and use zynqmp_pmufw_node() which
provides the same functionality.
Also add debug messages for easier debugging.
Fixes: e0283cbdfd49 ("power: zynqmp: Add power domain driver for ZynqMP")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/bddf11459b9b9e849fac9a50db2f1a5fdfae4119.1646122254.git.michal.simek@xilinx.com
Driver should be enabled by CONFIG_POWER_DOMAIN=y and
CONFIG_ZYNQMP_POWER_DOMAIN=y. Power domain driver doesn't have own DT node
but it uses zynqmp firmware DT node that's why there is a need to bind
driver when firmware node is found.
Driver itself is simple. It is sending pmufw config object overlay for
enabling access to device which is done in ...domain_request().
In ...domain_on() capabilities are passed and node is requested.
This should be bare minimum of required to get power domain driver working.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/f4b9433b91c0b18c375b061c7a4e29d428f70547.1644226055.git.michal.simek@xilinx.com
