Pinctrl driver was refactored and moved, but the required header that
it depends on was not included.
Fixes: 24d2908e987a ("pinctrl: qcom: move ipq4019 driver from mach-ipq40xx")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
IPQ4019 pinctrl driver was moved to the dedicated Qualcomm pinctrl
directory, but the KConfig depends on ARCH_SNAPDRAGON only and thus
PINCTRL_QCOM_IPQ4019 cannot be selected when ARCH_IPQ40XX is used.
Fixes: 24d2908e987a ("pinctrl: qcom: move ipq4019 driver from mach-ipq40xx")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
IPQ40xx SoC-s dont have proper SMEM support like more modern Qualcomm
SoC-s so there is no point in selecting the required drivers.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Give us lots of room for the appended FDT.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
These files are all identical (or older) than those in dts/upstream.
Drop them as we now use upstream DTS files with OF_UPSTREAM.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Switch to using upstream DT from dts/upstream.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The driver currently requires the bit clock divider be hardcoded in
devicetree (or use the hardcoded default from apq8016).
The bit clock divider is used to derive the baud rate from the core
clock:
baudrate = clk_rate / csr_div
clk_rate is the actual programmed core clock rate which is returned by
clk_set_rate(), and this UART driver only supports a baudrate of 115200.
We can therefore determine the appropriate value for UARTDM_CSR by
iterating over the possible values and finding the one where the
equation above holds true for a baudrate of 115200.
Implement this logic and drop the non-standard DT bindings for this
driver.
Tested on dragonboard410c.
Tested-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
clk_set_rate() should return the clock rate that was set. The IPQ4019
clock driver doesn't set any rates yet but it should still return the
expected value so that drivers can work properly.
For a baud rate of 115200 with an expected bit clock divisor of 16, the
clock rate should be 1843200 so return that frequency.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The clk_init_uart() helper always returns 0, but we're meant to return a
real clock rate. Given that we hardcode 115200 baud, just return the
clock rate that we set.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
MSM serial in DEBUG UART mode is trying to set .clk_rate, but the
msm_serial_data structure does not have such property at all, so lets
remove it as otherwise it will fail compiling.
Fixes: 90023bdfe979 ("serial: msm: add debug UART")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Currently, DEBUG_UART_MSM depends on ARCH_SNAPDRAGON only, but IPQ40XX
devices also use the same UART HW so they can also use the debug UART.
So, allow selecting DEBUG_UART_MSM when using ARCH_IPQ40XX as well.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The addresses were mistakenly swapped. Put them right.
Reported-by: Sumit Garg <sumit.garg@linaro.org>
Fixes: a737d8962cae ("mmc: msm_sdhci: correct vendor_spec_cap0 register for v5")
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Add the newly created u-boot-qcom mailing list to keep track of Qualcomm
patches.
Additionally, link to the U-Boot Snapdragon custodian tree.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Qcom SoCs derived boards can come from various OEMs/ODMs and not just
Qcom itself. So allow CONFIG_SYS_VENDOR to be set correctly
corressponding to the actual board vendor.
Suggested-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Add the GCC and TCSRCC clock driver for the SM8650 SoC.
The GCC driver uses the clk-qcom infrastructure to support GDSCs,
Resets and gates. While the TCSRCC is a simpler clock driver which
only supports gates.
The GCC enable and set_rate callbacks contains some tweaks to
setup clocks for Debug UART, SDCard controller and USB.
The TCSRCC gates returns the XO frequency, which is used by the
Synopsys eUSB2 driver to determine the PHY configuration.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Add the GCC and TCSRCC clock driver for the SM8550 SoC.
The GCC driver uses the clk-qcom infrastructure to support GDSCs,
Resets and gates. While the TCSRCC is a simpler clock driver which
only supports gates.
The GCC enable and set_rate callbacks contains some tweaks to
setup clocks for Debug UART, SDCard controller and USB.
The TCSRCC gates returns the XO frequency, which is used by the
Synopsys eUSB2 driver to determine the PHY configuration.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Remove the reference to the xo clock which is on the unsupported rpmhcc
clock controller. It isn't needed for MMC functionality.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Adjust sdm845_get_pin_name() to return the correct names for the special
pins. This fixes a non-fatal -ENOSYS error when probing MMC.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Allow setting the clock rate for the SD card core clock. This is
required for SD card support on SDM845 devices.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
We currently default to the lowest rate but this actually doesn't work
on most platforms. Default to the HS400 speed instead which is most
common on Qualcomm platforms.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
using fdtdec_* functions is incompatible with OF_LIVE and generally
offers a less friendly interface. Update to use dev_read_* functions
instead.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The V4 and V5 controllers have quite varied register layouts. Inherit
the register offsets and naming from the Linux driver. More version
specific offsets can be inherited from Linux as needed.
Fixes: 364c22a ("mmc: msm_sdhci: Add SDCC version 5.0.0 support")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Add a clock driver for the SM8250 SoC. This driver can enable necessary
clocks for UART, UFS, USB, and MMC.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Add a driver for the clock controller in the SM6115 SoC, this is used in
the QRB4210 RB2 board.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Finally add the entries for the qcom,pmk8350-pwrkey and qcom,pmk8350-resin
found on PMICs used with SM8350 and later SoCs.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Move node name checks to a proper data struct with all information
for the supported subnodes.
Replace the key offset defines with the Linux driver ones.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Add support for PM8550 GPIO controller variant, keep read-only
until the GPIO and Pinctrl setup is fixed for new PMICs.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Enable the clock and pinctrl drivers for qcm2290, sm6115, and sm8250.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
This SoC features a pinctrl block with north, south, and west tiles
accessible to the AP.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
This SoC features a pinctrl block with west, east, and south tiles.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
This SoC has a basic pinctrl block with no tiles.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Add pinctrl driver for the TLMM block found in the SM8650 SoC.
This driver only handles the gpio and qup2_se7 pinmux, and makes sure
the pinconf applies on SDC2 pins.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Add pinctrl driver for the TLMM block found in the SM8550 SoC.
This driver only handles the gpio and qup1_se7 pinmux, and makes sure
the pinconf applies on SDC2 pins.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Add a driver for the new Synopsys eUSB2 PHY found in the SM8550
and SM8650 SoCs.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Janne Grunau <j@jannau.net> says:
This series contains a few misc config changes for Apple silicon
systems:
- switch from the deprecated distro boot scripts to standard boot
- allows EFI console resizing based on the video console size
- enables 16x32 bitmap fonts as Apple devices come with high DPI
displays
- enables 64-bit LBA addressing
The bootflow list is only seen briefly and is probably more confusing
than helpful.
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Use standard boot instead of the distro boot scripts. Use
BOOTSTD_FULL instead of BOOTSTD_DEFAULTS for easier interactive use.
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Apple devices have high DPI displays so the larger fonts are preferable
for improved readability. This does not yet change the used font based
on the display's pixel density so the standard 8x16 font is still used
by default.
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Janne Grunau <j@jannau.net>
The display size querying in efi_console relies on this order. The
display should be the primary output device and should be used to
display more than 80x25 chars.
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Janne Grunau <j@jannau.net>
This makes USB HDDs >2TiB work. The only reason this hasn't bitten us
for the internal NVMe yet is the 4K sector size, because the largest SSD
Apple sells is 8TB and we can handle up to 16TiB with that sector size.
Close call.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Janne Grunau <j@jannau.net>
Michal Simek <michal.simek@amd.com> says:
I looked as cleaning up some dependencies and I found that qconfig is
reporting some issues. This series is fixing some of them. But there are
still some other pending. That's why please go and fix them if they are
related to your board.
UTF-8: I am using uni2ascii -B < file to do conversion. When you run it in
a loop you will find some other issue with copyright chars or some issues
in files taken from the Linux kernel like DTs. They should be likely fixed
in the kernel first.
Based on discussion I am ignoring names too.
Convert UTF-8 chars to ASCII in cases where make sense. No Copyright or
names are converted.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Marek Behún <kabel@kernel.org>
