When enabling/disabling a clock or reset signal, confirm that the change
has completed before returning from the function. A somewhat arbitrary
100ms timeout is defined to ensure that the system doesn't lock up in
the case of an error.
Since we need to dynamically determine if we're waiting for a 0 bit or a
1 bit, it's easier to use wait_for_bit_32() than readl_poll_timeout().
This change is needed for reliable initialization of the I2C driver
which is added in a following patch.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
i.MX93 uses the same USB IP as i.MX8MM. It can then reuse the ehci-mx6
driver.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
To prepare support for multiple register layouts pointers to register
tables where added to struct cpg_mssr_info. These pointers are suppose
to be filled in at probe time and no intended change in behavior was
intended.
However the new pointers where only filled in by some paths of the
driver implemented in clk-rcar-gen3.c. The path implemented in
clk-rcar-gen2.c was not updated leaving the pointers uninitialized
leading to a crash when trying to probe the clocks.
Fix this by filling in the pointers in the Gen2 code path with the
values used before they where moved to struct cpg_mssr_info.
Fixes: d413214fb7 ("clk: renesas: Add register pointers into struct cpg_mssr_info")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tested-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # R8A7791 Porter
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
This message isn't an error (there can be a watchdog subnode for example)
but it shouldn't be printed unless this driver is being debugged. Demote
it to a debug print.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
AM64 ES2.0 bootrom seems to enable WAIT0EDGEDETECTION interrupt.
This causes a lockup at A53 SPL when accessing NAND controller
or ELM registers.
A good option would be to softrest GPMC block at probe
but this cannot be done for AM64 as SOFTRESET bit is marked
as reserved in SYSCONFIG register.
Fix the issue by disabling all IRQs at probe.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Some platforms (such as the Lichee Pi 4A) have their dwmac device
addressable only in high memory space. Storing the node's base address
on 32 bits is not possible in such case.
Use platform's physical address type to store the base address.
Signed-off-by: Nils Le Roux <gilbsgilbert@gmail.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
ID code is added for zu67dr_SE, zu11eg_SE, zu19eg_SE and zu47dr_SE
variants. SE is the select edition of restricted devices with the
capabilities.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20240123045715.893652-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Recent i.MX8MP DTs use new fsl,imx6ul-ecspi compatible string instead
of the fsl,imx51-ecspi compatible string. Add the new compatible string
to fix ECSPI operation on i.MX8MP.
For details, see Linux:
48d74376fb68 ("arm64: dts: imx8mp: update ecspi compatible and clk")
8eb1252bbedf ("spi: imx: remove ERR009165 workaround on i.mx6ul")
Fixes: 451799a6ce ("arm: dts: imx8mp: Sync the DT with kernel 6.4-rc4")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Support RPC SPI on R8A779H0 V4M SoC.
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add PLL7 support to Gen3/Gen4 common clock driver. Add initial PLL7
multiplier and divider values into table in R8A779H0 V4M clock driver.
The PLL7 is new PLL added in R8A779H0 V4M SoC. Only integer multiplication
mode is supported by PLL7. The PLL reference clock are either 16.66 MHz or
20 MHz on R8A779H0 V4M SoC, and the output frequency must be 2000 MHz. The
multiplier values fitting this requirement are calculated to 120 or 100.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
- Add USB support for phycore-imx8mp
- Fix environment corruption, reset on mx6sabresd
- Print reset cause on imx8
- Extend mkimage to support generating an image for i.MXRT FlexSPI
- Add new apalis and colibri variants
- Add support for phyBOARD-Segin-i.MX93 support
- Fix when FEC is primarily used instead of EQOS on i.MX93.
Rename nxp_c45_tja11xx structure to nxp_c45_tja1103. The driver will
support more PHYs and nxp_c45_tja11xx is too generic.
Signed-off-by: "Radu Pirea (NXP OSS)" <radu-nicolae.pirea@oss.nxp.com>
Read PHY speed from hardware instead of assuming 100Mbps by default.
The TJA1103 works only at 100Mbps, but the driver will support more PHYs.
Signed-off-by: "Radu Pirea (NXP OSS)" <radu-nicolae.pirea@oss.nxp.com>
Use a local definition for the PHY features. PHY_100BT1_FEATURES are
not defined using the 100BaseT1 bit, so keep this workaround in the driver.
Signed-off-by: "Radu Pirea (NXP OSS)" <radu-nicolae.pirea@oss.nxp.com>
This error path should return -EINVAL instead of success.
Fixes: e261fbf347 ("blk: host_dev: Sanity check on the size of host backing file")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Add a comment to explain the code under is_secure condition of
ti_sci_do_xfer. This will help avoid confusion amongst people who may in
future touch upon this code.
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
The ti_sci driver in U-Boot has support for secure_msg as part of it's
do_xfer function. This let's U-boot send secure messages during boot up.
The protocol to send such secure messages is described as part of the
struct ti_sci_secure_msg_hdr. As part of this, there are 2 fields for
checksum and reserved that occupy the first 4 bytes of any secure
message. This is called as the secure_hdr.
As of now, the secure_hdr needs to be 0 init-ed before sending secure
messages. However the existing code was never putting the zero-inited vars
into the secure_buf, leading to possibility of the first 4 bytes of
secure_buf being possibly garbage.
Fix this by initialising the secure_hdr itself to the secure_buf
location, thus when we make secure_hdr members 0, it automatically ensures
the first 4 bytes of secure_buf are 0.
Fixes: 32cd25128b ("firmware: Add basic support for TI System Control Interface (TI SCI)")
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Testing has shown that writing to eMMC using HS400 modes on RK3568
result in an ERROR.
Change the tap number for transmit clock to fix this.
Also stop DLL when config_dll() is called to disable DLL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for ddr4 on rv1126. Timing detection files are imported
from downstream Rockchip BSP u-boot. Allow selecting ddr4 ram with
define CONFIG_RAM_ROCKCHIP_DDR4.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Some ethernet PHY require being reset before a phy-id can be read back
on the MDIO bus. This can result in the following message being show
on e.g. a Radxa ROCK Pi E v1.21 with a RTL8211F ethernet PHY.
Could not get PHY for ethernet@ff540000: addr -1
Add support to designware ethernet driver to reset eth phy by calling
the eth phy uclass function eth_phy_set_mdio_bus(). The call use NULL
as bus parameter to not set a shared mdio bus reference that would be
freed when probe fails. Also add a eth_phy_get_addr() call to try and
get the phy addr from DT when DM_MDIO is disabled.
This help fix ethernet on Radxa ROCK Pi E v1.21:
=> mdio list
ethernet@ff540000:
1 - RealTek RTL8211F <--> ethernet@ff540000
Reported-by: Trevor Woerner <twoerner@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In the SMBIOS 3 entry point the Structure Table Maximum Size field was
incorrectly named max_struct_size. A Maximum Structure Size field only
exists in the SMBIOS 2.1 entry point and has a different meaning.
Call the Structure Table Length field table_maximum_size.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
For RISC-V CPUs the SMBIOS Processor ID field contains
the Machine Vendor ID from CSR mvendorid.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This patch adds an implementation of the Andes watchdog ATCWDT200 driver.
Signed-off-by: CL Wang <cl634@andestech.com>
Signed-off-by: Randolph <randolph@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmW4mGIcHGV1Z2VuLmhy
aXN0ZXZAY29sbGFib3JhLmNvbQAKCRAesx4CDqwvyBq9B/sHzeh4lWQpyU5CcO8J
WnlRn2blqL/2LzkawD6OvA7WhEYisLh2389q6pPSFqWZS8v1aNgTO4krnPDOG3a5
s7yigcBtg5KsmnM4K89+KZ/BZW4TzrSHIY4P+t1W92QtnFHEzNW/LolG6jBZnz+e
bMzi0uCGR1cgTW4IfLmuq6NajIaAXywdohMxfi/9kiNhQVT03Jux/CGoIvpJ61Bu
OKWX2KNn0o3XXK7UKdZUSzP6CyiRSplQl3eX/0shh9qPR16eSeUqh952zGxlcOZO
PKXvDMl8QxkCzRjXdg3EH2jADoaTB0maq6JutVyY+SoLiYJ9A8BUCLOIMevCVXjK
3BCH
=V29u
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2024.04-a' of https://source.denx.de/u-boot/custodians/u-boot-at91
First set of u-boot-at91 features for the 2024.04 cycle:
This set includes some DT alignments and solves a compile issue for
custom nand defconfigs.
This ports the pad drive strength register configuration which can be
already found in the Linux driver for this PHY.
Signed-off-by: Lukasz Tekieli <tekieli.lukasz@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Make sure that core SDHCI accessors are used and add
device specific card detection initialization, which
is borrowed from vendor Linux driver code.
Tested-by: Jens Maus <mail@jens-maus.de>
Tested-by: Darko Alavanja <darko.alavanja@konsulko.com>
Signed-off-by: Ivan T. Ivanov <iivanov@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
brcm,bcm2708-fb device provided by firmware on RPi5 uses
16 bits per pixel, so lets calculate framebuffer bytes
per pixel dynamically based on queried information.
Tested to work for RPi2b v1.2, RPi3b v1.3, RPi4b v1.1,
RPi2 Zero W, RPi5b v1.0.
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Tested-by: Jens Maus <mail@jens-maus.de>
Tested-by: Darko Alavanja <darko.alavanja@konsulko.com>
Signed-off-by: Ivan T. Ivanov <iivanov@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Existing gpio-gate-clock driver acts like a simple GPIO switch without any
effect on gated clock. Add actual clock actions into enable/disable ops and
implement get_rate op by passing gated clock if it is enabled.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20240110160956.4476-2-clamor95@gmail.com
[ sorted includes ]
Signed-off-by: Sean Anderson <seanga2@gmail.com>
When we call clk_get_rate(), we expect to get clock rate value as
ulong.
In that case we should not use log_ret() macro since it use internally
an int.
Otherwise we may return an invalid/truncated clock rate value.
Signed-off-by: Julien Masson <jmasson@baylibre.com>
Fixes: 5c5992cb90 ("clk: Add debugging for return values")
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/87o7erv9p4.fsf@baylibre.com
Amlogic SoCs embeds an hardware clock measure block, port it
from Linux and implement it as a UCLK_CLK with only the dump
op and fail-only xlate.
Based on the Linux driver introduced in [1].
[1] commit 2b45ebef39a2 ("soc: amlogic: Add Meson Clock Measure driver").
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231218-uboot-meson-clk-msr-v3-1-acf4d90ccfee@linaro.org
Without explicit support for VIDEO_X2R10G10B10 VIDEO_X8R8G8B8 white
will be rendered as cyan-ish. The conversion leaves to lowest 2 bits
unset for more compact code.
Signed-off-by: Janne Grunau <j@jannau.net>
Use device-tree node property names for parsing nodes instead of
indexing as indexing could be different between different SoCs based on
number of DSS entities available on that particular SoC.
Also correct the video layer naming in driver to match to actual one
being used in upstream DSS device-tree node [1].
This also fixes AM62x splash screen usage using the latest upstream DSS
device-tree nodes where hard-coded indexing which driver was using
before this patch was not matching the correct properties in the DT
node.
[1]: Upstream AM62x DSS node:
https://github.com/torvalds/linux/blob/v6.8-rc1/arch/arm64/boot/dts/ti/k3-am62-main.dtsi#L774
Fixes: 5f9f816bb8 ("drivers: video: tidss: TIDSS video driver support for AM62x")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
Devarsh Thakkar <devarsht@ti.com> says:
Move video memory reservation for SPL at end of RAM so that it does
not interefere with reservations for next stage so that the next stage
need not have holes in between for passed regions and instead it can
maintain continuity in reservations.
Also catch the bloblist before starting reservations to avoid the same
problem.
While at it, also fill missing fields in video handoff struct before
passing it to next stage.
This is as per discussions at :
For moving SPL framebuffer reservation at end of RAM:
https://lore.kernel.org/all/CAPnjgZ3xSoe_G3yrqwuAvoiVjUfZ+YQgkOR0ZTVXGT9VK8TwJg@mail.gmail.com/
For filling missing video handoff fields :
https://lore.kernel.org/all/CAPnjgZ1Hs0rNf0JDirp6YPsOQ5=QqQSP9g9qRwLoOASUV8a4cw@mail.gmail.com/
Fill video handoff fields in video_post_probe as at this point we have
full framebuffer-related information.
Also fill all the fields available in video hand-off struct as those
were missing earlier and U-boot framework expects them to be filled for
some of the functionalities.
While filling framebuffer size in video hand-off structure use the
actual framebuffer region size as derived from gd->video_top and
gd->video_bottom instead of directly using the size populated in
video_uc_plat as it contains unaligned size.
Reported-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Skip framebufer reservation if it was already reserved from previous
stage and whose information was passed using a bloblist.
Return error in case framebuffer information received from bloblist is
invalid i.e NULL or empty.
While at it, improve the debug message to make it more clear that
address in discussion is of framebuffer and not bloblist and also match
it with printing scheme followed in video_reserve function.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make the "phy-handle" property optional, which allows support
for a fixed-link phy configuration.
Thus if the "phy-handle" is present in a DT, then driver will work as
before. Otherwise, phyaddr initialization will not be necessary,
as it is not needed in case of a fixed-link config.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Infineon(Cypress) S28HS02GT is 1.8V, 2Gb (256MB) NOR Flash memory with
Octal interface. It is a dual-die package parts and has same features
with existing S28 series.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Enabling Octal DTR mode in multi-die package parts requires reister setup
for each die. That can be done by simple for-loop. write_enable() takes
effect to all die at once so we can call it before the loop. Besides we
can replace spi_mem_exec_op() calls with spansion_read/write_any_reg().
And finally, we must mask CFR2V[7:4] when changing dummy cycles, as
CFR2V[7] indicates current addressing mode and that should be 1 (4-byte
address mode) for multi-die package parts.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
s28hx_t_post_bfpt_fixup() fixes erase opcode, erase size, and page size.
s25_post_bfpt_fixup() is doing same thing including multi-die support.
We can consolidate s28hx_t_post_bfpt_fixup() and s25_post_bfpt_fixup()
into one named s25_s28_post_bfpt_fixup().
In s25_s28_post_bfpt_fixup(), set_4byte() is called to force the device to
be 4-byte addressing mode. In S28HS02GT datasheet, the B7 opcode is missing
but it works actually (confirmed).
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
s28hx_t_setup() only checks sector layout setting. To support multi-die
package parts like S28HS02GT, it needs to check device size and assign
ready() hook for multi-die package parts. These are covered in s25_setup()
so we can consolidate s28hx_t_setup() and s25_setup() into one named
s25_s28_setup().
spi_nor_wait_till_ready() at the beginning of s28hx_t_setup() can be
removed since there is no op that makes device busy state before setup.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
s25_mdp_ready() handles status polling for multi-die package parts that
requires to read and check status register for each die. To support
S28HS02GT(dual-die package with Octal DTR support), rename function and
use nor->rdsr_dummy in octal DTR mode.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Infineon(Cypress) S28Hx-T family does not support legacy CLSR(0x30) opcode.
Instead, it supports CLPEF(0x82) which has the same functionality as CLSR.
spansion_sr_ready() is for multi-die package parts including S28HS02GT, so
we need to use CLPEF instead of CLSR.
This change does not affect to S25x02GT which uses spansion_sr_ready() as
S25Hx-T family also supports CLPEF(0x82) as well as CLSR(0x30).
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
In Infineon multi-die package parts, we need to use Read Any Register op
to read status register in 2nd or further die. Infineon S28HS02GT is
dual-die package and supports Octal DTR interface. To support this,
spansion_read_any_reg() needs to be reworked. Implementation is similar
to existing read_sr() that already supports Octal DTR mode.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
s25_erase_non_uniform() and s28hx_t_erase_uniform() support hybrid sector
layout (32 x 4KB sectors overlaid at bottom address) and doing same thing.
Consolidate them into single helper named s25_s28_erase_non_uniform().
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Some macro definitions used in Infineon(Cypress) S25 and S28 series are
redundant and some have inconsistent prefix. This patch removes
redundant ones and renames some to have same prefix as others.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The current implementation encounters issues when testing data ranging
from 0 to 8 bytes. This was confirmed through testing with both ISSI
(IS25WX256) and Micron (MT35XU02G) Flash exclusively in SDR mode.
Upon investigation, it was observed that utilizing the
"SPI_NOR_OCTAL_READ" flag and attempting to read less than 8 bytes in
STIG mode results in a read failure, leading to a compare test failure.
To resolve this issue, the CMD_4BYTE_FAST_READ opcode is now utilized
instead of CMD_4BYTE_OCTAL_READ, specifically in SDR mode.
This is based on patch series:
https://lore.kernel.org/all/cover.1701853668.git.tejas.arvind.bhumkar@amd.com/
Signed-off-by: Tejas Bhumkar <tejas.arvind.bhumkar@amd.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Added support for the ISSI OSPI flash part IS25LX512M.
Initial testing was performed on the Tenzing-se1 board using
SDR mode, covering basic erase, write, and readback operations.
Signed-off-by: Tejas Bhumkar <tejas.arvind.bhumkar@amd.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
If even one byte is lost due to Rx FIFO overflow then we will never
exit the read loop. Because the (priv->rx != priv->rx_end) condition will
be always true.
Let's check if Rx FIFO overflow occurred and exit the read loop
in this case.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The header file is not necessary in either of those files,
remove it as common.h is going away.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
The header file is not necessary in either of those files,
remove it as common.h is going away.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
The current code convert the SMBIOS 2.1 entry point structure to
SMBIOS 3.0 entry point structure. The max_struct_size member in
SMBIOS 2.1 entry point structure indicates
"Size of the largest SMBIOS structure, in bytes".
We need to use struct_table_length instead.
Fixes: 1c5aab803c ("smbios: copy QEMU tables")
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Enable serial support for Exynos850 SoC by adding the corresponding
compatible string. No additional changes needed, the driver works as is
on Exynos850. Related USI and PMU configuration is enabled in separate
drivers. The only other dependencies are clock and pinctrl drivers,
which are already enabled too.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add pinctrl support for Exynos850 SoC. It was mostly extracted from
corresponding Linux kernel code [1]. Power down modes and external
interrupt data were removed while converting the code for U-Boot, but
everything else was kept almost unchanged.
[1] drivers/pinctrl/samsung/pinctrl-exynos-arm64.c
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Heavily influenced by its Linux kernel counterpart. It's implemented on
top of recently added Samsung CCF clock framework API. For now only UART
leaf clocks are implemented, along with all preceding clocks in CMU_TOP
and CMU_PERI. The UART baud clock is required in the serial driver, to
get its rate for the consequent baud rate calculation.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Heavily based on Linux kernel Samsung clock framework, with some changes
to accommodate the differences in U-Boot CCF implementation. It's also
quite minimal as compared to the Linux version.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
PLL utilities code is only used by clk-exynos7420 driver at the moment.
Move it into clk-exynos7420 to make clk-pll.c file available for CCF PLL
clocks implementation, which is coming in the next patches.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add basic Power Management Unit (PMU) driver for Exynos SoCs. For now
it's only capable of changing UART path in PMU, which is needed for
E850-96 board. The driver's structure resembles the exynos-pmu driver
from Linux kernel, and although it's very basic and slim at the moment,
it can be easily extended in future if the need arises.
UCLASS_NOP is used, as there are no benefits in using more elaborate
classes like UCLASS_MISC in this case. The DM_FLAG_PROBE_AFTER_BIND flag
is added in bind function, as the probe function must be always called
for this driver.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
USIv2 IP-core is found on modern ARM64 Exynos SoCs (like Exynos850) and
provides selectable serial protocol (one of: UART, SPI, I2C). USIv2
registers usually reside in the same register map as a particular
underlying protocol it implements, but have some particular offset. E.g.
on Exynos850 the USI_UART has 0x13820000 base address, where UART
registers have 0x00..0x40 offsets, and USI registers have 0xc0..0xdc
offsets. Desired protocol can be chosen via SW_CONF register from System
Register block of the same domain as USI.
Before starting to use a particular protocol, USIv2 must be configured
properly:
1. Select protocol to be used via System Register
2. Clear "reset" flag in USI_CON
3. Configure HWACG behavior (e.g. for UART Rx the HWACG must be
disabled, so that the IP clock is not gated automatically); this is
done using USI_OPTION register
4. Keep both USI clocks (PCLK and IPCLK) running during USI registers
modification
This driver implements the above behavior. Of course, USIv2 driver
should be probed before UART/I2C/SPI drivers. It can be achieved by
embedding UART/I2C/SPI nodes inside of the USI node (in Device Tree);
driver then walks underlying nodes and instantiates those. Driver also
handles USI configuration on PM resume, as register contents can be lost
during CPU suspend.
This driver is designed with different USI versions in mind. So it
should be relatively easy to add new USI revisions to it later.
Driver's code was copied over from Linux kernel [1] and adapted
correspondingly for U-Boot API. UCLASS_MISC is used, and although no
misc operations are implemented, it makes it easier to probe the driver
this way (as compared to UCLASS_NOP) and keep the code compact.
[1] drivers/soc/samsung/exynos-usi.c
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The help for CONFIG_MTD explains that it needs to be enabled for various
things like NAND, etc to be available. It however then doesn't enforce
this dependency and so if you have none of these systems present you
still need to disable a number of options. Fix this by making places
that select/imply one type of flash, but did not do the same, also do
this for "MTD". Make boards which hadn't been enabling MTD already but
need it now, do so. In a few places, disable CONFIG_CMD_MTDPARTS as it
wasn't previously enabled but was now being implied.
Signed-off-by: Tom Rini <trini@konsulko.com>
MEMCLKMGR_EXTCNTRST_C0CNTRST register defined as BIT[0] in documentation
but it is wrongly defined as BIT[7] in u-boot code. This register is used
to hold associated pingpong counter in reset
while PLL and 5:1 mux configuration is changed.
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
These removed definitions were specific to some sam9 SoCs, but not
generic over all at91 SoCs. The correct SoC specific definitions for
ATMEL_BASE_PMECC are spread over different header files in
arch/arm/mach-at91/include/mach directory.
Fixes a build error on a custon board based on SAMA5D2:
Building current source for 73 boards (16 threads, 1 job per thread)
arm: + vera2
+drivers/mtd/nand/raw/atmel/pmecc.c:819: warning: "ATMEL_BASE_PMECC" redefined
+ 819 | #define ATMEL_BASE_PMECC 0xffffe000
+ |
+In file included from include/configs/vera2.h:11,
+ from include/config.h:3,
+ from include/linux/mtd/rawnand.h:16,
+ from drivers/mtd/nand/raw/atmel/pmecc.c:44:
+include/asm/arch/sama5d2.h:171: note: this is the location of the previous definition
+ 171 | #define ATMEL_BASE_PMECC (ATMEL_BASE_HSMC + 0x70)
+drivers/mtd/nand/raw/atmel/pmecc.c:820: warning: "ATMEL_BASE_PMERRLOC" redefined
+ 820 | #define ATMEL_BASE_PMERRLOC 0xffffe600
+include/asm/arch/sama5d2.h:172: note: this is the location of the previous definition
+ 172 | #define ATMEL_BASE_PMERRLOC (ATMEL_BASE_HSMC + 0x500)
Fixes: a490e1b7c0 ("nand: atmel: Add pmecc driver")
Signed-off-by: Alexander Dahl <ada@thorsis.com>
STM32MP1:
---------
Set stdio to serial on DH STM32MP15xx DHSOM
Fix reset for usart1 in scmi configuration
STM32MP2:
---------
Add BSEC and OTP support for STM32MP25
Fix CONFIG_STM32MP25X flag usage
-----BEGIN PGP SIGNATURE-----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=BoSU
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20240119' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add CMDLINE dependecy for CMD_STM32KEY
STM32MP1:
---------
Set stdio to serial on DH STM32MP15xx DHSOM
Fix reset for usart1 in scmi configuration
STM32MP2:
---------
Add BSEC and OTP support for STM32MP25
Fix CONFIG_STM32MP25X flag usage
- A number of OS boot related cleanups, a number of TI platform
fixes/cleanups, SMBIOS fixes, tweak get_maintainers.pl to report me
for more places, fix the "clean the build" pytest and add a bootstage
pytest, fix PKCS11 URI being omitted in some valid cases, make an iommu
problem easier to debug on new platforms, nvme and pci improvements,
refactor image-host code a bit, fix a typo in env setting, add a missing
dependency for CMD_LICENSE, and correct how we call getchar() in some
places.
CONFIG options must not use lower-case letter. Convert this and related
ones to upper case.
Signed-off-by: Simon Glass <sjg@chromium.org
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
CONFIG options must not use lower-case letter. Convert this and related
ones to upper case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Complete the transition away from xhci-dwc3 and dwc3-of-simple drivers
and change to use the dwc3-generic driver on remaining RK3328 and RK3399
boards.
MISC, USB_DWC3 and USB_DWC3_GENERIC is enabled on boards that used to
enable USB_XHCI_DWC3. USB_XHCI_DWC3 is dropped from updated boards along
with the default y of USB_XHCI_DWC3_OF_SIMPLE.
There is no intended change in functionality with this changes, USB 3.0
is expected to continue same as before this change.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A busy controller shouldn't be game-over for all controllers,
so keep trying on hitting -EBUSY.
This change brings the actual behavior of the routine in line
with what the descriptions says.
Fixes: 982388eaa9 ("nvme: Add NVM Express driver support")
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Moritz Fischer <moritzf@google.com>
Return -EBUSY if controller is found busy rather than -ENOMEM
and update the error message accordingly.
Fixes: 982388eaa9 ("nvme: Add NVM Express driver support")
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Moritz Fischer <moritzf@google.com>
This enables 64b BARs if CONFIG_SYS_PCI_64BIT is enabled.
Reviewed-by: Philip Oberfichtner <pro@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Moritz Fischer <moritzf@google.com>
When attempting to probe a device which has an associated IOMMU, if the
IOMMU device can't be found (no driver, disabled driver, driver failed
to probe, etc) then we currently fail to probe the device with no
discernable error.
If we fail to hook the device up to its IOMMU, we should make sure that
the user knows about it. Write some better error messages for
dev_iommu_enable() to facilitate this.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
* add generated index to table of contents
* create index entries for commands
* update Python packages used to build the documentation
* fix typos in dfu documentation
UEFI:
* split unrelated code from efi_bootmgr.c
* rename CONFIG_BOOTEFI_BOOTMGR to CONFIG_EFI_BOOTMGR
* net: tftp: remove explicit EFI configuration dependency
* fs: remove explicit EFI configuration dependency
Other:
* Add Goldfish RTC driver and make it available on RISC-V QEMU
-----BEGIN PGP SIGNATURE-----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=q+5u
-----END PGP SIGNATURE-----
Merge tag 'efi-2024-04-rc1-2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Documentation:
* add generated index to table of contents
* create index entries for commands
* update Python packages used to build the documentation
* fix typos in dfu documentation
UEFI:
* split unrelated code from efi_bootmgr.c
* rename CONFIG_BOOTEFI_BOOTMGR to CONFIG_EFI_BOOTMGR
* net: tftp: remove explicit EFI configuration dependency
* fs: remove explicit EFI configuration dependency
Other:
* Add Goldfish RTC driver and make it available on RISC-V QEMU
The Goldfish RTC is a virtual device which may be supplied by QEMU.
It is enabled by default on QEMU's RISC-V virt machine.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add reset controller driver for Nuvoton BMCs.
The npcm reset driver not only supports reset each module reset
but setting initial value of reset Control Registers.
And The driver support each module reset.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
QEMU provides SMBIOS tables with detailed information. We should not try to
replicate them in U-Boot.
If we want to inform about U-Boot, we can add a Firmware Inventory
Information (type 45) table in future.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Qualcomm architecture changes:
* Move clock and pinctrl drivers out of mach-snapdragon
* Various clock driver improvements
* Convert PMIC power/reset key driver to use the button API
* Preparetory work for migrating to upstream DT
Linux DTs stuff a value indicating if the USID is a USID or a GSID in the
reg property, the Linux SPMI driver then reads the two address cells
separately. U-boot's dev_read_addr() doesn't know how to handle this, so
use ofnode_read_u32_index() to get just the USID.
The Qcom pmic driver doesn't have support for GSID handling, so just
ignore the second value for now.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The core and chnl register ranges were swapped on SDM845. Fix it, and
fetch the register ranges by name instead of by index.
Drop the cosmetic "version" variable and clean up the debug logging.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
This property is not part of the dt bindings and all boards use the new
gpio-ranges property instead. Drop support for this.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Upstream uses the gpio-ranges property to define the number of GPIOs,
support for parsing this when gpio-count is unspecified
Additionally, drop the bank-name property as it isn't used in upstream,
and we can just hardcode the bank name instead.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Remove the (now unused) GPIO driver for the power and resin buttons on
the PMIC.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Qualcomm PMICs include a "pon" function which handles two buttons, the
power button and "resin" button (usually volume down). Introduce a new
driver following upstream Linux DT to enable these and map them to Enter
and Down respectively to enable use in boot menus.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
priv->pid is uint32_t, but dev_read_addr() returns a uint64_t on arm64,
with the upper bits being used for error codes. Do error checking before
downcasting to u32 to prevent errors being silently ignored.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
devm_clk_get() returns an ERR_PTR on failure, not null. Fix the check to
avoid the board crashing when the clock isn't available.
Additionally, add the missing error handling for this function.
Fixes: 324df15a29 ("serial: qcom: add support for GENI serial driver")
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
commit 1b15483deb ("misc: add Qualcomm GENI SE QUP device driver")
introduced support for platform-specific oversampling values, necessary
to configure the UART clocks on all platforms at runtime. However it
relies in probing a parent device. Despite the DM_FLAG_PRE_RELOC flag,
this is not done consistently during boot.
Instead, take another approach by relying on ofnode_ helpers to read the
serial engine base address and do the read directly. This fixes early
UART on boards with a non-default oversampling rate.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The pinctrl and GPIO drivers are currently heavily incompatible with
upstream. Most Qualcomm pinctrl blocks feature "tiles" of pins, each at
it's own address. Introduce support for these by allowing the soc driver
to specify per-pin register offsets similarly to the Linux driver.
Adjust the GPIO driver to handle these too, and finally enable support
for all pins with the same numbering as used in Linux.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Drop the duplicated pinctrl-snapdragon driver from mach-ipq40xx and add
it to drivers/pinctrl/qcom.
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Move the Qualcomm pinctrl drivers out of mach-snapdragon and over to the
rest of the pinctrl drivers, adjust the drivers so that support for each
platform can be enabled/disabled individually and introduce platform
specific configuration options.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The RCG divider field takes a value of (2*h - 1) where h is the divisor.
This allows fractional dividers to be supported by calculating them at
compile time using a macro.
However, the clk_rcg_set_rate_mnd() function was also performing the
calculation. Clean this all up and consistently use the F() macro to
calculate these at compile time and properly support fractional divisors.
Additionally, improve clk_bcr_update() to timeout with a warning rather
than hanging the board, and make the freq_tbl struct and helpers common
so that they can be reused by future platforms.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
This property is needed on some platforms to ensure that only the
relevant bits are set in the M/N/D registers.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Currently, it isn't possible to build clock drivers for more than one
platform due to how the msm_enable() and msm_set_rate() callbacks are
implemented.
Extend qcom_clk_data to include function pointers for these and convert
all platforms to use them.
Previously, clock drivers relied on include/configs/<board.h> to include the
board specific sysmap header, however as most of the header contents are clock
driver related, import the contents directly into each clock driver and
remove the header. The only exception here is the dragonboard820c board file
which includes some pinctrl macros, those are also inlined.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
[caleb: remove additional sysmap-sdm845.h mention]
Many gate clocks can be enabled with a single register write, add support
for defining these simple gate clocks and add the ones found on SDM845.
While we're here, inline clk_init_uart() into msm_set_rate().
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Qualcomm's clock controller blocks actually do much more than it
says on the tin.. They provide clocks, resets and power domains.
Currently, U-Boot requires one to spawn 2 separate devices for
controlling clocks and resets, both spanning the same register space.
Refactor the code to make it work with just a single DT node, making
it compatible with upstream Linux bindings and dropping the dedicated
reset driver in favour of including it in the clock driver.
Heavily inspired by Renesas code for a similar hw block.
[caleb: moved drivers to clk/qcom, added reset driver and adjusted bind
logic. Imported qcom,gcc-ipq4019.h from Linux]
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
This driver is just a stub, but it's necessary to support the upcoming
reset driver changes.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Clock drivers don't belong here, move them to the right place and
declutter mach-snapdragon a bit.
To de-couple these drivers from specific "target" platforms, add
additional config options to enable each clock driver gated behind a
common CLK_QCOM option and enable them by default for the respective
targets. This will make future work easier as we move towards a generic
Qualcomm target.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Set NAND chip ofnode and device so OF based partition parsing
can work.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://www.mail-archive.com/u-boot@lists.denx.de/msg499178.html
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
For DM case we can get the NAND chip's IO address from DT
so we don't need to rely on CFG_SYS_NAND_BASE.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://www.mail-archive.com/u-boot@lists.denx.de/msg499177.html
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
sys_proto.h no longer exists for K3 platform so drop it.
Include sizes.h to so SZ_16M is visible.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://www.mail-archive.com/u-boot@lists.denx.de/msg499176.html
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
The macro ELM_BASE is defined in mach/hardware.h and is
not visible at the omap_elm.h header file. Avoid using it
in omap_elm.h.
Reported-by: Hong Guan <hguan@ti.com>
Fixes: 7363cf0581 ("mtd: rawnand: omap_elm: u-boot driver model support")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/all/20231211114600.4414-3-rogerq@kernel.org
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
AM335x uses a special driver "am335x_spl_bch.c" as SPL
NAND loader. This driver expects 1 sector at a time ECC
and doesn't work well with multi-sector ECC that was implemented in
commit 04fcd25873 ("mtd: rawnand: omap_gpmc: Fix BCH6/16 HW based correction")
Additionally, the omap_elm driver does not support multi sector ECC and will
need more work and tests to get multi sector working correctly on all
platforms.
Switch back to 1 sector at a time read/ECC.
Fixes: 04fcd25873 ("mtd: rawnand: omap_gpmc: Fix BCH6/16 HW based correction")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Tested-by: Enrico Leto <enrico.leto@siemens.com>
Tested-by: Heiko Schocher <hs@denx.de>
Link: https://lore.kernel.org/all/20231211114600.4414-2-rogerq@kernel.org/
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
If the "mtd" parameter is NULL, the search will definitely yield a
negative result. In that case, it's better to exit immediately.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Link: https://lore.kernel.org/all/20231102113829.58852-1-dario.binacchi@amarulasolutions.com
Synchronize R-Car R8A77960 M3-W and R8A77961 M3-W+ clock tables with Linux 6.6.3,
commit bd3a9e5771a8b332f466d06f7c130a69cab0d526 .
Add ZG clock macro into rcar-gen3-cpg.h to cover the new clock type .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add properties to improve eye diagram which sometimes need adjust
some parameters of u2phy;
Add a property to tune disconnect threshold;
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
debug print delays reset of the driver. Finally I see
bunch of "rx error FFFF" errors in the screen. CI can
not handle many prints. While network works fine there
Reproduced with:
make CROSS_COMPILE=sh2-linux- r2dplus_defconfig all
qemu-system-sh4 -M r2d -nographic -serial null \
-serial mon:stdio -net user,tftp=`pwd` \
-net nic,model=rtl8139 -kernel ./u-boot.bin
Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
return value of smc911x_send is ignored, but on sucesseful
send we need return 0 and or error -ETIMEOUT, not opposite.
Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
u-boot-dfu-20240111
- Implement fastboot multi-response. This allows multi-line response and
most importantly, finally adds support for fastboot getvar all command.
- New 'fastboot oem console' command. Useful for debugging to send data
the u-boot shell via fastboot
- Console recording fixes
* make table_compute_checksum() arguments const
* remove duplicate function verify_checksum()
* enable setting processor family > 0xff
* set correct SMBIOS processor family value for RISC-V
* avoid importing ofnode.h in smbios.h
* provide a UEFI tool to dump SMBIOS table
-----BEGIN PGP SIGNATURE-----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=oHtG
-----END PGP SIGNATURE-----
Merge tag 'smbios-2024-04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request smbios-2024-04-rc1
* make table_compute_checksum() arguments const
* remove duplicate function verify_checksum()
* enable setting processor family > 0xff
* set correct SMBIOS processor family value for RISC-V
* avoid importing ofnode.h in smbios.h
* provide a UEFI tool to dump SMBIOS table
Use counterpart dev_read_* functions instead of fdt* ones. It fixes
checkpatch warnings like this:
WARNING: Use the livetree API (dev_read_...)
#54: FILE: drivers/pinctrl/exynos/pinctrl-exynos.c:137:
pinvals[idx] = fdtdec_get_int(fdt, node,
and also makes it possible to avoid using the global data pointer in the
driver.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Pull some variables declared in exynos_pinctrl_set_state() into its
loop, to reduce their scope. Style commit, no functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
All pin related dt properties (pin-function, pin-pud and pin-drv) are
handled in a very similar way. Get rid of that code duplication by
extracting the corresponding data knowledge into an actual data
structure (array), and then just iterating over it.
No functional change, it's a refactoring commit.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Get rid of hard-coded register offsets and widths. Instead provide a way
for pinctrl drivers to specify different pin bank register offsets and
widths. This in turn makes it possible to add support for new SoCs that
have registers with offset/width values different than generic ones
already available in pinctrl-exynos driver.
Offset constants (now unused in pinctrl-exynos.c) are moved to
pinctrl-exynos7420 driver, which is the single user of those constants.
The design of this patch follows Linux kernel pinctrl-exynos driver
design, in terms of added data structures and types. This patch doesn't
add support for any new SoCs and shouldn't introduce any functional
changes.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rework pin_to_bank_base() function to obtain bank data structure by bank
name instead of getting bank base address by pin name, and rename it to
get_bank() to reflect this change. This in turn leads to the extraction
of parse_pin(), so the caller has to use it before calling get_bank().
No functional change. This is a refactoring commit which prepares
pinctrl driver code for handling different sizes of register fields,
which will be added next.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Next commits are going to re-design the pin_to_bank_base() function and
its usage in a way that the pin parsing code will be called separately.
Extract it into a separate function first, as a refactoring commit.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Currently u-boot fastboot can only send one message back to host,
so if there is a need to print more than one line messages must be
kept sending until all the required data is obtained. This behavior
can be adjusted using multiresponce ability (getting multiple lines
of response) proposed in this patch.
Signed-off-by: Ion Agorria <ion@agorria.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20240105072212.6615-2-clamor95@gmail.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
The SMBIOS specification requires to set the processor family in the type 4
(Processor Information) table to specific values depending only on the
bitness of the system (0x200 for RV32 and 0x201 for RV64).
With this patch dmidecode shows
Handle 0x0004, DMI type 4, 48 bytes
Processor Information
Socket Designation: Not Specified
Type: Central Processor
Family: RV64
for qemu-riscv64_smode_defconfig.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The existence of devices should be checked in the bind method and not in
the probe method. Adjust the RISC-V Zkr RNG driver accordingly.
Use ENOENT (and not ENODEV) to signal that the device is not available.
Fixes: ceec977ba1 ("rng: Provide a RNG based on the RISC-V Zkr ISA extension")
Reported-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
In different parts of our code we assume that the first RNG device is the
one to be used. Therefore it is preferable to detect the availability of
the RNDR register already in the bind method.
For signaling the non-existence of a device the driver model requires using
ENOENT (and not ENODEV).
Fixes: 31565bb0aa ("driver: rng: Add DM_RNG interface for ARMv8.5 RNDR registers")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Invoke write_acpi_tables() via EVT_LAST_STAGE_INIT on QEMU except on X86.
X86 calls write_acpi_tables() in write_tables().
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move the code related to copying tables from QEMU to a separate code
module.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
We have two implementations of write_acpi_tables(). One for writing ACPI
tables based on ACPI_WRITER() entries another based on copying tables from
QEMU.
Create a symbol CONFIG_QFW_ACPI that signifies copying ACPI tables from
QEMU and use it consistently.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver is currently responsible for enabling the clock gating
feature of SiFive pre core's private L2 cache.
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add a basic implementation of the ARM SMMU. This driver is intended for
use on Qualcomm platforms where the SMMU has been configured by a previous
bootloader, cannot be turned off, and doesn't support BYPASS streams.
It keeps all existing stream mappings and only creates new ones for stream
ids that aren't already configured.
This driver is necessary to support peripherals that perform DMA which
weren't configured by the previous stage bootloader (for example USB).
It works by allocating a context bank using identity mapping (as U-Boot
doesn't use virtual addresses).
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Add an optional iommu callback to be invoked before a device probes.
This can be used to configure the IOMMU in preparation for the device
(e.g. by allocating a context bank)
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The dev_pci_iommu_enable() function is only available when CONFIG_PCI is
enabled, replace the runtime check with a preprocessor one to fix
compilation with pci disabled.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
These files include <common.h> twice. Start by removing the second
inclusion of the file.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to make it easier to move on to dropping common.h from code
directly, remove common.h inclusion from the rest of the header file
which had been including it.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
We need to include <config.h> directly when a file needs to have
something such as CFG_SYS_SDRAM_SIZE referenced as this file is not
automatically globally included and is most commonly indirectly included
via common.h. Remove most cases of arm including config.h directly, but
add it where needed. This includes a few board-specific fixes.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
In general terms, we -include include/linux/kconfig.h and so normal
U-Boot code does not need to also #include it. However, for code which
is shared with userspace we may need to add it so that either our full
config is available or so that macros such as CONFIG_IS_ENABLED() can be
evaluated. In this case make sure that we guard these includes with a
test for USE_HOSTCC so that it clear as to why we're doing this.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEPVPGJshWBf4d9CyLd9zb2sjISdEFAmWCxMoACgkQd9zb2sjI
SdFG2A//Zc/bbiy8GPZ5Hi3hgB90H5xVjsivgMW2Riw5ZiMiC3v8klKlzbKprzNy
1Zf4002A/yn470YIDInUFEJVc1ZeGbyMj9u7HDId+/4FhtdXVWGjON+lINlShrWL
FX9ITBbxBKEfno6uoDD1Gy5xq1LFl3kXSeingGZnm3W+b9FJb9mo2X1UgUE70Pkp
Kw/dyL6ZVmvAGnuuonc55Kxgoc5m92Ww2wJxbLMCYmPwqHRveduGZfS6nQxJnJU7
XT8fOK5GsAbYWMnI63Nf5Bue6yTCKJH8CE7Kg1mJjMNm+Ictqo/aCQX3S1nZiBL0
CHvHOhrck3Db5+AfmKQDwYofb/Haaf97auf1sGCi/PVnmLn1c3BPON3qyK2Qvjbx
1WAvWea5I97Pv8hMGEPecTMACgTF3XOJIBGXMuAc5ScO3rlckeSZdb/m5/3nHEei
ZcwfxNMw8OqECnIG/13NoYkOGEWG22DtoNuD75ESztKGAz3YL5Rfr+siZniyGNsq
9ZdFVf7AQwDSRUmcpFN9ETawfU8Y9rK7fp5L6yUTTCKtQBL1+qUPyYb2KvH1LvfH
PKECA9D6XKpdgLHjyAJrMHlpaOQiqBDAUvZrdDGZWHMaKSL8XXZKPaj2a124RqtW
NZfri43xj5a/AeeMBAkRrz3BzFfXn5EGoGdbduq+HXnJTaMCrdI=
=aBS6
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-next-20231220' of https://source.denx.de/u-boot/custodians/u-boot-amlogic into next
- Add support for new GXL MDIO mux, with driver and Linux DT sync from v6.4
Move all existing pinmux and funcmux code into a dedicated folder in
pinctrl to simplify further maintenance.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The existing pinctrl driver available for Tegra SOC is well
designed, but it lacks DM support. Let's add a DM compatible
overlay, which allows use of the device tree, along with preserving
backward compatibility with all existing setups and the ability
to use it in SPL board configuration stage.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The driver currently hard-codes the max freqency for the sdhci
controllers. If the controller is unable to operate at the max
frequency, the mmc card will not be available on the first scan.
Subsequent scans will eventually find a working combination.
Fix this by allowing the driver to check for the max-frequency
property and default to the original value if it doesn't exist.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
UCLASS_PMIC may have GPIO children without exposed fdt node,
in this case if requesting fails, check if uclass is PMIC.
Restrict build for supported devices only to save those precious
bytes on devices with no spare memory.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
MAXIM Semiconductor's PMIC, MAX77663 has 8 GPIO pins and 3 GPIO-like
pins. It also supports interrupts from these pins.
Add GPIO driver for these pins to control via GPIO APIs.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Julien Masson <jmasson@baylibre.com> says:
This patch series add the support for the MediaTek MT8365 EVK Board [1].
Most of the code have been copied/adapted from Linux tag v6.7-rc2.
For now we only enable/test these features:
Boot, UART, Watchdog and MMC.
[trini: This includes two clocks not listed in the Linux binding, which
needs resyncing later]
This patch adds clock driver support for MediaTek MT8365 SoC.
The changes are based on the Linux source code tag v6.7-rc2.
clk-mt8365.c has been written based on these kernel files:
- clk-mt8365.c (a96cbb146a9736f501fe66ebda6a9018735e5e8a)
- clk-mt8365-apmixedsys.c (65c9ad77cbc0eed78db94d80041aba675cfbdfa9)
And adapted following the clk attributes supported by U-Boot.
Signed-off-by: Julien Masson <jmasson@baylibre.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
The block count limit on MMC based devices should be set according to
CONFIG_SYS_MMC_MAX_BLK_COUNT instead of hardcoding value.
Signed-off-by: Julien Masson <jmasson@baylibre.com>
Change optee driver service enumeration to not enumerate (and
allocate a zero sized shared memory buffer) when OP-TEE
reports that there is no service to enumerate.
This change fixes an existing issue that occurs when the such zero
sized shared memory buffer allocated from malloc() has a physical
address of offset 0 of a physical 4kB page. In such case, OP-TEE
secure world refuses to register the zero-sized shared memory
area and makes U-Boot optee service enumeration to fail.
Fixes: 94ccfb78a4 ("drivers: tee: optee: discover OP-TEE services")
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Change optee probe function to only warn when service enumeration
sequence fails instead of reporting an optee driver probe failure.
Indeed U-Boot can still use OP-TEE even if some OP-TEE services are
not discovered.
Fixes: 94ccfb78a4 ("drivers: tee: optee: discover OP-TEE services")
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
DSP core is going into abnormal state when load callback is called
after starting of DSP core.
Reload of firmware needs core to be stopped first, followed by
load.
So avoid loading of firmware, when core is started.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Port the mdio-mux-meson-gxl.c Linux driver introduced in [1],
and adapt it to U-Boot.
This driver is needed to boot U-Boot with Linux DT since v6.4,
since it switched the MDIO mux from the mmio to a proper GXL driver.
[1] 9a24e1ff4326 ("net: mdio: add amlogic gxl mdio mux support")
Link: https://lore.kernel.org/r/20231213-u-boot-gxl-mdio-mux-v2-1-c56bb02a75ea@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add timer driver in Starfive SoC. It is an timer that outside
of CPU core and inside Starfive SoC.
Signed-off-by: Kuan Lim Lee <kuanlim.lee@starfivetech.com>
Signed-off-by: Wei Liang Lim <weiliang.lim@starfivetech.com>
Changes for v2:
- correct driver name, comment, variable
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The main thing in here is Igor's conversion of soc_clk_dump to a clk_ops
member. There's also a write-protect feature for nuvoton clocks.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
-----BEGIN PGP SIGNATURE-----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=z+Sl
-----END PGP SIGNATURE-----
Merge tag 'clk-2024.01-next' of https://source.denx.de/u-boot/custodians/u-boot-clk into next
clock patches for u-boot/next
The main thing in here is Igor's conversion of soc_clk_dump to a clk_ops
member. There's also a write-protect feature for nuvoton clocks.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Assign ccf_clk_ops to .ops of clk_ccf driver so that it can act as an
clk provider. Also add "#clock-cells=<1>" to its device tree node.
Add "i2c_root" to clk_test in the device tree and driver for testing.
Get "i2c_root" clock in CCF unit tests and add tests for it.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20231111-enable_count-v3-2-08a821892fa9@outlook.com
Add a flag to set ahb/apb/fiu/spi clock divider as read-only
The spi clock setting is related to booting flash, it is setup by early
bootloader.
It just protects the clock source and can't modify it in uboot.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20231114090004.3746024-1-JJLIU0@nuvoton.com
Switch to using new dump operation in clock provider drivers instead of
overriding soc_clk_dump.
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Igor Prusov <ivprusov@sberdevices.ru>
Link: https://lore.kernel.org/r/20231109105516.24892-8-ivprusov@sberdevices.ru
It's possible for composite clocks to have a divider that does not
implement set_rate() operation. For example, sandbox_clk_composite()
registers composite clock with a divider that only has get_rate().
Currently clk_composite_set_rate() only checks thate rate_ops are
present, so for sandbox it will cause NULL dereference during
clk_set_rate().
This patch adds rate_ops->set_rate check tp clk_composite_set_rate().
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20231205232334.2931-2-ivprusov@salutedevices.com
For some gate clocks and fixed clocks without a parent, calling
clk_register will print an useless error message indicating that parent
is missing. Fix that by gaurding log_xxx() with an if-statement.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Suggested-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20230807-clk-fix-v2-1-0b688e21fb4e@outlook.com
Add support to Orise Tech OTM8009A display on stm32f469-disco board.
It was necessary to retrieve the framebuffer address from the device tree
because the address returned by the video-uclass driver pointed to a memory
area that was not usable.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Set pllsaidivr only if the PLLSAIR output frequency is an exact multiple
of the pixel clock rate. Otherwise, we search through all combinations
of pllsaidivr * pllsair and use the one which gives the rate closest to
requested one.
Fixes: 5e993508cb ("clk: clk_stm32f: Add set_rate for LTDC clock")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The value to be written to the register must be appropriately shifted,
as is correctly done in other parts of the code.
Fixes: 5e993508cb ("clk: clk_stm32f: Add set_rate for LTDC clock")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add PLL settings for DDR 3600 MTps . This is very similar to 3200 MTps
PLL setting, except the divider is not 9 but 8 .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The new MX8M DDR tool 3.31 now generates a programming file which uses
data rate 3734 instead of 3733 or 3732 . Handle another rounding option .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
We are not iterating CQSPI_REG_RETRY, we are waiting 'timeout' ms, since
day 1.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Adaptation of Linux commit d74c36480a67
This patch adds support for ESMT F50L1G41LB and F50D1G41LB.
It seems that ESMT likes to use random JEDEC ID from other vendors.
Their 1G chips uses 0xc8 from GigaDevice and 2G/4G chips uses 0x2c from
Micron. For this reason, the ESMT entry is named esmt_c8 with explicit
JEDEC ID in variable name.
Datasheets:
https://www.esmt.com.tw/upload/pdf/ESMT/datasheets/F50L1G41LB(2M).pdfhttps://www.esmt.com.tw/upload/pdf/ESMT/datasheets/F50D1G41LB(2M).pdf
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Martin Kurbanov <mmkurbanov@sberdevices.ru>
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Tested-by: Martin Kurbanov <mmkurbanov@sberdevices.ru>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
During SFDP header parse and BFPT parse, structures in stack are used
to perform spi_nor_read_sfdp() which expects a dma-safe buffer.
This commit introduces spi_nor_read_sfdp_dma_unsafe() to wrap
spi_nor_read_sfdp() using a kmalloc'ed bounce buffer which is
the same implementation in Linux (drivers/mtd/spi-nor/sfdp.c).
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
- Add TPM support for venice boards
- Add networking support for imx93-evk
- Enable TCP, IPv6, wget for DHCOM and Data Modul boards
- Enable fastboot support for Toradex boards
- Allow pico-imx7d to boot from SD
- Enable fastboot for beacon imx8m beacon boards, disabled
SYS_CONSOLE_IS_IN_ENV
- Fix mxsboot to prevent NAND blocks being reported as bad
- Add imx8mm PWM clock support
- Several devicetree syncs with the kernel
- Add support for i.MX8MP Polyhex Debix Model A SBC
- Reworked ddr_load_train_firmware() to get a 50ms boot time improvement
Check the header before starting to use it, since this could provide
very confusing later, when ofnode calls start to fail.
Signed-off-by: Simon Glass <sjg@chromium.org>
Function acpi_get_rsdp_addr() is needed on all architectures which
write ACPI tables. Move the definition from the x86 include to an
architecture independent one.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To quote the author:
It would be useful to be able to boot an OS when CONFIG_CMDLINE is
disabled. This could allow reduced code size.
Standard boot provides a way to handle programmatic boot, without
scripts, so such a feature is possible. The main impediment is the
inability to use the booting features of U-Boot without a command line.
So the solution is to avoid passing command arguments and the like to
code in boot/
A similar process has taken place with filesystems, for example, where
we have (somewhat) separate Kconfig options for the filesystem commands
and the filesystems themselves.
This series starts the process of refactoring the bootm logic so that
it can be called from standard boot without using the command line.
Mostly it removes the use of argc, argv and cmdtbl from the internal
logic.
Some limited tidy-up is included, but this is kept to smaller patches,
rather than trying to remove all #ifdefs etc. Some function comments
are added, however.
A simple programmatic boot is provided as a starting point.
This work will likely take many series, so this is just the start.
Size growth with this series for firefly-rk3288 (Thumb2) is:
arm: (for 1/1 boards) all +23.0 rodata -49.0 text +72.0
This should be removed by:
https://source.denx.de/u-boot/custodians/u-boot-dm/-/issues/11
but it is not included in this series as it is already large enough.
No functional change is intended in this series.
Changes in v3:
- Add a panic if programmatic boot fails
- Drop RFC tag
Changes in v2:
- Add new patch to adjust position of unmap_sysmem() in boot_get_kernel()
- Add new patch to obtain command arguments
- Fix 'boot_find_os' typo
- Pass in the command name
- Use the command table to provide the command name, instead of "bootm"
Add some functions which provide an argument to a command, or NULL if
the argument does not exist.
Use the same numbering as argv[] since it seems less confusing than the
previous idea.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Tom Rini <trini@konsulko.com>
To quote the author:
I wanted to add support for ti,lp5562, and found an old submission
from Doug. While trying to modify that to work in current U-Boot, I
found a problem with the "move label handling to core" patches.
Patch 1 is a prerequisite for the ti,lp5562 driver, which turned out
to be needed by Christian as well.
Patch 2 is an attempt at (quick-)fixing the mentioned "move label
handling to core" problem. The real fix consists of changing remaining
drivers to not bind the same driver to the top node as to the child
nodes, but I can't test those other drivers.
Patch 3 introduces a helper which should allow removing some
boilerplate in most individual drivers, and 4,5 apply that in the gpio
and pwm drivers. Converting remaining drivers is trivial, but left out
for now.
Finally patch 6 is the reworked lp5562 driver. While I've changed it
to match existing DT bindings (with the goal of making it work with
our .dts that is known to work with the linux driver), most of the
logic is unchanged from Doug's original patch, so he is still listed
as author.
Changes in v2: Interchange order of patches 1 and 2, add a few R-bs,
and try to trim down the commit message in patch 2.
Driver for the TI LP5562 4 channel LED controller. Supports
independent on/off control of all 4 channels. Supports LED_BLINK on 3
independent channels: blue/green/red. The white channel can blink, but
shares the blue channel blink rate.
Heavily based on patch originally from Doug Zobel [1].
I have modified it so it matches the DT bindings in the linux tree,
and also follows the linux driver implementation more closely. This
should address Tom's concerns, and also matches my goal of making the
U-Boot driver work with our existing .dts which is known to work in
linux.
As our boards only have the R,G,B outputs connected, I have not
actually tested how the white channel behaves, but the R,G,B work
exactly as expected.
[1] https://lore.kernel.org/u-boot/1547150757-1561-1-git-send-email-douglas.zobel@climate.com/
Cc: Doug Zobel <douglas.zobel@climate.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Use the helper led_bind_generic() to reduce code duplication.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Use the helper led_bind_generic() to reduce code duplication.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
All existing drivers in drivers/led/ contain a .bind method that does
exactly the same thing, with just the actual driver name
differing. Create a helper so all those individual methods can be
changed to one-liners.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Many existing drivers, and led-uclass itself, rely on uc_plat->label
being NULL for the device representing the top node, as opposed to the
child nodes representing individual LEDs. This means that the drivers
whose .probe methods rely on this were broken by commit 83c63f0d11
("led: Move OF "label" property parsing to core"), and also that the top
node wrongly shows up with 'led list'.
Binding the same driver to the top node as to the individual child
nodes is arguably wrong, and the approach of using a UCLASS_NOP driver
for the top node is probably better - this has for example been done in
commit 0107469780 ("led: gpio: Use NOP uclass driver for top-level
node") and commit 910b01c27c ("drivers: led: bcm6753: do not use null
label to find the top")
Until remaining affected drivers are fixed, we can use a heuristic
that only sets the label to the fallback value derived from the node
name if the node does not have a "compatible" property - i.e., if it
has been bound to the LED driver explicitly via
device_bind_driver_to_node(). This is similar to what commit
e3aa76644c ("led: gpio: Check device compatible string to determine
the top level node") did for gpio_led, but that fix was then supplanted
by commit 0107469780 ("led: gpio: Use NOP uclass driver for top-level
node")
Fixes: 83c63f0d11 ("led: Move OF "label" property parsing to core")
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
If the driver's own .bind method has populated uc_plat->label, don't
override that. This is necessary for an upcoming driver for ti,lp5562,
where the DT binding unfortunately says to use "chan-name" and not
"label".
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Display port is using topsw_lsbus clock, it is failing
while enabling the clock, so enable the topsw_lsbus clock.
Signed-off-by: Sreekanth Sunnam <sreekanth.sunnam@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231204084515.9488-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Both FS_LOADER and SPL_FS_LOADER have the same menu prompt.
To avoid confusion, make prompt for SPL_FS_LOADER different.
Signed-off-by: Alexander Gendin <agendin@matrox.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Based on Linux kernel 6.7-rc4, add necessary clocks for the PWM
controllers.
Signed-off-by: Nicolas Heemeryck <nicolas.heemeryck@devialet.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Currently, when running "ums 0 mmc 2" and breaking it via
CTRL + C, the following message is seen:
u-boot=> ums 0 mmc 1
UMS: LUN 0, dev mmc 1, hwpart 0, sector 0x0, count 0x1dacc00
CTRL+C - Operation aborted
clk usb_phy_root_clk already disabled
The USB PHY clock is disabled twice: first it gets disabled
inside imx8mq_usb_phy_power_off(), then it is disabled again
inside imx8mq_usb_phy_exit().
Let the USB PHY clock be disabled only once inside
imx8mq_usb_phy_power_off() by removing the .exit operation.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Add support for DWC EQoS MAC on i.MX93.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Function ddr_load_train_firmware() is called 4 times in a loop by
ddr_cfg_phy(). The first 3 calls are all '1D' type and just loading the
same FWs. Let's add a type check and save 2 of them. This helps to
reduce DDRPHY training time from 269 ms down to 212 ms, and thus speed
up boot time ~ 50 ms.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
As of now only one mailbox agent is supported by mailbox driver.
On zynqmp platform there are about 7 mailbox agents which can communicate
over same IPI channel to U-Boot. This patch series introduces new
"zynqmp_ipi_dest" driver which adds one to multi-channel mailbox
support.
Following format in device-tree is expected as per latest bindings:
zynqmp-ipi {
compatible = "xlnx,zynqmp-ipi-mailbox";
mbox_1: mailbox@1 {
/* New compatible for child node */
compatible = "xlnx,zynqmp-ipi-dest-mailbox";
...
};
...
mbox_n: mailbox@n {
compatible = "xlnx,zynqmp-ipi-dest-mailbox";
...
}
};
Then mailbox client uses child mailbox node as following:
ipi-dest-1 {
...
mboxes = <mbox_1 0>, <mbox_1 1>;
mbox-names = "tx", "rx";
...
};
New "zynqmp_ipi_dest" driver is for devices with
"xlnx,zynqmp-ipi-dest-mailbox" compatible string. This driver will take care
of mailbox send recv ops and it replaces previous "zynqmp_ipi" driver.
Now "zynqmp_ipi" driver simply binds each child device with "zynqmp_ipi_dest"
driver.
However, its important to maintain backward comaptibility with previous
bindings where child node does not have compatible string. In such case, new
driver isn't probed by U-Boot during boot and system fails to boot. To
resolve this issue firmware-zynqmp.c driver probes all the IPI parent node
driver which binds each child node device with "zynqmp_ipi_dest" driver.
This makes sure corresponding child driver will be
probed when requested using mbox_get_by_name or mbox_get_by_idx
framework calls.
This way multiple mailbox agents are supported in device-tree without breaking
previous binding support.
Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
Link: https://lore.kernel.org/r/20231204215620.63334-4-tanmay.shah@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
If U-Boot is running in Exception Level 3 then use hardcode
register values for mailbox message passing with PMU.
This is only supported for zynqmp platform.
Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
Link: https://lore.kernel.org/r/20231204215620.63334-3-tanmay.shah@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Use SMC calls to TF-A to operate IPI for execution level below 3. For
EL3 use hardcode IPI registers as TF-A isn't available in EL3.
Hence, in EL3 remote and local IPI ids retrieved using xlnx,ipi-id
property are unused.
Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
Link: https://lore.kernel.org/r/20231204215620.63334-2-tanmay.shah@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add the xfer callback which is used by the MMC_SPI driver and generally by
the dm_spi_xfer callback.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Tested-by: Love Kumar <love.kumar@amd.com>
Link: https://lore.kernel.org/r/20231116164336.140171-3-mchitale@ventanamicro.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Modify start_transfer and related functions to take a udevice parameter
as input instead of spi_slave. This is needed so that start_transfer can
be used directly via the xfer callback. Also fix a compiler warning.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Tested-by: Love Kumar <love.kumar@amd.com>
Link: https://lore.kernel.org/r/20231116164336.140171-2-mchitale@ventanamicro.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The host bridge MMIO region is disabled by default due to which MMIO
accesses cause an exception. Fix it by setting the bridge enable bit.
This change is ported from the linux pcie-xilinx driver.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20231116165103.140968-3-mchitale@ventanamicro.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
As per the xlnx,axi-ethernet-1.00.a DT documentation in linux, the AXI
DMA registers can be obtained via the reg property or via a separate
node for the axistream DMA controller. Currently only the latter is
supported, so add support to fetch the DMA controller registers from the
"reg" property.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20231116164024.139934-1-mchitale@ventanamicro.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
- StarFive: Add StarFive watchdog driver
- VisionFive2: Support device tree overlay for VisionFive2 board
- Andes: Fix PLIC-SW setting
- RISC-V: Fix NVMe support by implying NVME_PCI for QEMU
- RISC-V: Fix binman for 64 bit format load address
Currently spi driver gets flash parameter from first subnode.
Few boards have more than one flash with different parameters
and selection of flash is done by on board switch settings.
In such case, uboot needs to be recompiled with updated
device tree to align with board switch settings.
This patch allows to select flash node at runtime.
Boards those are supporting multiple flashes
needs to implement cadence_qspi_get_subnode function and return correct
flash node.
Cc: Apurva Nandan <a-nandan@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
MT25QU01 OPN with 4B OPCODE support is currently not supported in
source code and the driver reuses the definition for "n25q00a"
which has the same silicon ID but is a slower part.
Adding mt25u01g definition to the source code to support a faster
read response for MT25QU01 QSPI NOR Flash device.
Signed-off-by: Jit Loon Lim <jit.loon.lim@intel.com>
[jagan: fix the id position and commit head]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add Support for GigaDevice GD55LB02GEBIR SPI NOR flash as QSPI
configuration flash
Signed-off-by: Teik Heng Chong <teik.heng.chong@intel.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The original H616 devices released about three years ago were typically
paired with an X-Powers AXP305 PMIC. Newer devices uses the smaller
AXP313, and there seem to be far more systems with this PMIC around now.
Remove the default AXP305 selection for the H616 SoC from the Kconfig,
and move the PMIC selection into the board defconfig files instead.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add support for the zBIT ZB25VQ128 (128M-bit) SPI NOR flash memory chip,
as used on the Xunlong Orange Pi Zero 3 board.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
When build for arm64 target, comipler reports the following warning:
drivers/spi/bcm63xx_hsspi.c: In function ‘bcm63xx_hsspi_xfer_dummy_cs’:
include/linux/kernel.h:184:17: warning: comparison of distinct pointer
types lacks a cast
184 | (void) (&_min1 == &_min2); \
| ^~
drivers/spi/bcm63xx_hsspi.c:298:22: note: in expansion of macro ‘min’
298 | size_t curr_step = min(step_size, data_bytes);
This change fix this warning by casting the data_bytes to size_t.
Fixes: 0e144ec38c ("spi: bcm63xx-hsspi: Add prepend mode support")
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Add to support StarFive watchdog driver. The driver is imported from
linux kernel's drivers/watchdog/starfive-wdt.c without jh7100 support
because there is no support of jh7100 SoC in u-boot yet.
Howver, this patch has been kept the variant coding style because JH7100
can be added later and have a consistency with the linux driver.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add JH7110_SYSCLK_WDT_APB and JH7110_SYSCLK_WDT_CORE clocks for JH7110
watchdog device.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The wdt_start function takes timeout_ms as a parameter and starts the
watchdog with this value. However, when you output the message, it shows
the default timeout value for the watchdog device.
So this patch fixes that part to output the correct timeout value.
Before -->
StarFive # wdt start 3000
WDT: Started watchdog@13070000 without servicing (60s timeout)
After -->
StarFive # wdt start 3000
WDT: Started watchdog@13070000 without servicing (3s timeout)
Fixes: c2fd0ca1a8 ("watchdog: Integrate watchdog triggering into the cyclic framework")
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Compiling with CONFIG_USB_XHCI_PCI and CONFIG_PCI=n results in
usb/host/xhci-pci.c:48:(.text.xhci_pci_probe+0x44):
undefined reference to `dm_pci_write_config32
Add the missing Kconfig dependency.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Like Rockchip RK3328 and RK3568, the RK3588 also have a single node to
represent the glue and ctrl for USB 3.0.
Use rk_ops as driver data to select correct ctrl node for RK3588 DWC3.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Marek Vasut <marex@denx.de>
We need to get the DMA address before incrementing the pointer, as that
might move us onto another segment.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
Now that we always check the return value, just return NULL on timeouts.
We can still log the error since this is a problem, but it's not reason
to panic.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
This isn't going to work, don't pretend it will and then end up timing
out.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
There is currently no codepath to recover from this case. In principle
we could require that the upper layer do this explicitly, but let's just
do it in xHCI when the next bulk transfer is started, since that
reasonably implies whatever caused the problem has been dealt with.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
There is a race where an endpoint may halt by itself while we are trying
to halt it, which results in a context state error. See xHCI 4.6.9 which
mentions this case.
This also avoids BUGging when we attempt to stop an endpoint which was
already stopped to begin with, which is probably a bug elsewhere but
not a good reason to crash.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
If the xHC has a problem with our STOP ENDPOINT command, it is likely to
return a completion directly instead of first a transfer event for the
in-progress transfer. Handle that more gracefully.
We still BUG() on the error code, but at least we don't end up timing
out on the event and ending up with unexpected event errors.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
xhci_wait_for_event returns NULL on timeout, so the caller always has to
check for that. This addresses immediate explosions in this part
of the code when timeouts happen, but not the root cause for the
timeout.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
This is a hacky way to have this file included in all source files that
include common.h, instead just include from the files that need it.
Signed-off-by: Andrew Davis <afd@ti.com>
The current implementation may cause BUG_ON() in blkfront_aio()
BUG_ON(n > BLKIF_MAX_SEGMENTS_PER_REQUEST);
In pvblock_iop(), a read/write operation will be split into smaller
chunks of data so that the size in one access (aio_nbytes) is limited
to, at the maximum,
BLKIF_MAX_SEGMENTS_PER_REQUEST * PAGE_SIZE
But this works only if when the *buffer* passed in to pvblock_io()
is page-aligned. If not, the given data region may stand across
(BLKIF_MAX_SEGMENTS_PER_REQUEST + 1) pages. See the logic in
blkfront_aio():
start = (uintptr_t)aiocbp->aio_buf & PAGE_MASK;
end = ((uintptr_t)aiocbp->aio_buf + aiocbp->aio_nbytes +
PAGE_SIZE - 1) & PAGE_MASK;
Then this will lead to BUG_ON() above.
This can be fixed by decreasing the maximum size of aio_nbytes.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Fixes: commit 3a739cc6c9 ("xen: pvblock: Implement front-back protocol and do IO")
Currently the "clock-frequency" DT property is only being considered as an
fallback if either there is no clock driver, the clock driver implements
the request-op correctly or there is no clock defined for the timer at all.
This patch makes "clock-frequency" also being picked as a fallback if
getting the clock-rate fails, since clk_get(_by_index) will return no
error, if a clock driver does not implement the request-op and does also
not support getting the rate of the clock in question.
timer_post_probe will take care if the property does not exist in the DT or
is defined as 0.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
To quote the author:
"Scmi" command will be re-introduced per Michal's request.
The functionality is the same as I put it in my patch set of adding
SCMI base protocol support, but made some tweak to make UT, "ut dm
scmi_cmd," more flexible and tolerable when enabling/disabling a specific
SCMI protocol for test purpose.
Each commit may have some change history inherited from the preceding
patch series.
Test
====
The patch series was tested on the following platforms:
* sandbox
This change will be useful when we manually test SCMI on sandbox
by enabling/disabling a specific SCMI protocol.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
To quote the author:
This series imports generic versions of ioread_rep/iowrite_rep and
reads/writes from Linux. Some cleanup is done to make sure that all
platforms have proper defines for implemented functions and there are no
redefinitions.
Since {read,write}s{l, w, b}() functions are now supported in linux/io.h
there is no need to add custom implementation to driver.
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Directly including asm-generic/io.h may break build because it will
cause redefenition of generic io macros if linux/io.h gets included
later, hence replace it with direct include of linux/io.h
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Currently {read,write}s{b,w,lq}() functions are available only on some
architectures, and there are no io{read,write}{8,16,32,64}_rep()
functions in u-boot. This patch adds generic versions that may be used
without arch-specific implementation.
Since some of added functions were already added locally in some files,
remove them to avoid redeclaration errors.
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
To quote the author:
The show_board_info() function was adjusted to weak so that it could be
entirely replaced with a board-specific implementation.
The intended way for boards to provide their own information is via a
sysinfo driver. But currently there is no way to show anything other
than the model name.
This series adds support for showing a few more items, in a way that is
easy for boards to extend.
Since there is already a weak checkboard() function, we don't need to
have two levels of weak function here. So this series drops the weak
attribute from show_board_info()
Existing boards will see a slight change in output, in that the model
name will appear first, before any custom output. If that is a problem,
then the solution is to implement a sysinfo driver for the board.
At present only the model name is shown on start. Some boards want to
display more information. Add some more options to allow display of the
manufacturer as well as the version and date of any prior-stage
firmware.
This is useful for coreboot, at least. If other boards have more
information to display, it is easy to add it, now.
Signed-off-by: Simon Glass <sjg@chromium.org>
The "i2cbcdev" sneaked in when implementing this function for the
bootcounter use case. Obviously the intention was to use prop_name
instead.
Fixes: b483552773 (i2c: Implement i2c_get_chip_by_phandle())
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Extend the version check to handle UFS 3.1 controllers as well.
Tested on QEMU emulated UFS 3.1 controller.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a simple PCI based UFS controller driver with a QEMU
emulated UFS controller on the PCI bus.
Requiring QEMU v8.2+.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Check if the UFS controller is on the PCI bus, and get its register
base address accordingly.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Add a line feed to improve readability of some dev_xxx() messages.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
UFS stands for Universal Flash Storage, not Subsytem.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
As the address read from device tree is being cast to a pointer, it's
better to use dev_read_addr_ptr() API for getting that address. The more
detailed explanation can be found in commit a12a73b664 ("drivers: use
dev_read_addr_ptr when cast to pointer").
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
u-boot-dfu-next-20231124
- Make dfu entity name size configurable in KConfig
- Implement start-stop for UMS (graceful shutdown via eject)
- Improve help messages for cmd/bind
- Improve help message for udc bind failures
Just some minor style fixes. No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Get rid of magic numbers in s5p_serial_init() when writing to UART
registers. While at it, use BIT() macro for existing constants when
appropriate.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Use dev_read_u8_default() instead of fdtdec_get_int() to read the "id"
property from device tree, as suggested in [1]. dev_* API is already
used in this driver, so there is no reason to stick to fdtdec_* API.
This also fixes checkpatch warning:
WARNING: Use the livetree API (dev_read_...)
[1] doc/develop/driver-model/livetree.rst
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
It's not really needed here anymore. Remove it, as common.h is going
away at some point.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
In preparation for enabling ethernet for the am62ax family of SoCs,
introduce the initial DMA channel settings for the am62ax
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
[bb@ti.com: expanded on commit message]
Signed-off-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Checking if variable chip is NULL after dereferencing it makes no sense.
As discribed in [1] it is not expected that the variable can ever be NULL.
[1] Re: [PATCH] tpm: avoid NULL pointer dereference in tpm_tis_send()
https://lore.kernel.org/u-boot/YaFwDtKKYRr7qzWc@apalos.home/
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
At some point when trying to use USB gadgets, two situations may arise
and lead to a failure. Either the UDC (USB Device Controller) is not
available at all (not described or not probed) or the UDC is already in
use. For instance, as the USB Ethernet gadget remains bound to the UDC,
the use of any other USB gadget (fastboot, dfu, etc) *after* will always
fail with the "couldn't find an available UDC" error.
Let's give a more helpful message by making a difference between the two
cases. Let's also hint people who would get this error and grep it into
the sources a better explanation of what's wrong with their workflow.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20231010090304.49335-4-miquel.raynal@bootlin.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Today CMD_BIND defaults to 'y' when USB_ETHER is enabled. In practice,
CMD_BIND should default to 'y' when any USB gadget is enabled not only
USB_ETHER. Let's invert the logic of the dependency and use the weak
'imply' keyword to enforce this.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on vim3
Link: https://lore.kernel.org/r/20231010090304.49335-2-miquel.raynal@bootlin.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Exit the UMS handler loop in case START-STOP UNIT SCSI command is
received. This is sent e.g. by the util-linux eject(1) command and
indicates to the device that it is supposed to spin down the media
and enter low power state.
This effectively adds support for exitting the 'ums' command from
host using 'eject /dev/sdN' that is on par with 'dfu-util -e' .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20231107001018.55640-1-marex@denx.de
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Add CONFIG_DFU_NAME_MAX_SIZE to change the proper size.
If name is longer than default size, it can do wrong behavior during updating
image. So it need to change the proper maximum size.
This patch is proviced the solution to change value with configuration.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Link: https://lore.kernel.org/r/20220620111354.448512-1-jh80.chung@samsung.com
[mkorpershoek: fixed build errors for dfu.h includes]
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
The ChipIdea device controller wasn't properly cleaned up when disabled.
So enabling it again left it in a broken state. The problem occurred for
example when the host unbinds the driver and binds it again.
During the first setup, when the out request is queued, the endpoint is
primed (`epprime`). If the endpoint is then disabled, it stayed primed
with the initial buffer. So after the endpoint is re-enabled, the device
controller and device driver were out of sync: the new out request was
in the driver queue head, yet not submitted, but the "complete" function
was still called, since the endpoint was primed with the old buffer.
With the fastboot function this error led to the (rather confusing)
error message "buffer overflow".
Fixed by clearing the primed buffers with the `epflush` (`ENDPTFLUSH`)
register.
Signed-off-by: Simon Holesch <simon@holesch.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20231120002024.32865-1-simon@holesch.de
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
SCSI device scan code was executing TEST UNIT READY command without
explicitly setting dma direction in struct scsi_cmd to NONE, so command
was passed to driver with dma direction set to DMA_FROM_DEVICE,
inherited from older usage.
With WDC SDINDDH6-64G ufs device, that caused TEST UNIT READY to
return error.
Fix that, by explicitly setting dma direction to NONE for
TEST UNIT READY, and restoring it back DMA_FROM_DEVICE for the
following READ CAPACITY.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Marek Vasut <marex@denx.de>
User needs to call several functions to create the ramdisk
with blkmap.
This adds the utility function to create blkmap device and
mount the ramdisk.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
According to the virtio v1.x "entropy device" specification, a virtio-rng
device is supposed to always return at least one byte of entropy.
However the virtio v0.9 spec does not mention such a requirement.
The Arm Fixed Virtual Platform (FVP) implementation of virtio-rng always
returns 8 bytes less of entropy than requested. If 8 bytes or less are
requested, it will return 0 bytes.
This behaviour makes U-Boot's virtio_rng_read() implementation go into an
endless loop, hanging the system.
Work around this problem by always requesting 8 bytes more than needed,
but only if a previous call to virtqueue_get_buf() returned 0 bytes.
This should never trigger on a v1.x spec compliant implementation, but
fixes the hang on the Arm FVP.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reported-by: Peter Hoyes <peter.hoyes@arm.com>
- squashfs improvements, remove common.h in some places, assorted code
fixes, fix a few CONFIG symbol names in Kconfig files, bring in
linux's <linux/time.h> conversion functions, poplar updates, bcb
improvements.
The intent here is to only allow SPL_LEGACY_BLK if !SPL_DM - i.e. that
when driver model is enabled in SPL, legacy block cannot be used.
However this combination is used by about 240 boards, so we cannot
disallow it, at least not yet.
So just drop the condition.
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently BCB C API only allows to modify 'command' BCB field.
Extend it so that we can also read and modify all the available
BCB fields (command, status, recovery, stage).
Co-developed-by: Cody Schuffelen <schuffelen@google.com>
Signed-off-by: Cody Schuffelen <schuffelen@google.com>
Signed-off-by: Dmitrii Merkurev <dimorinny@google.com>
Cc: Eugeniu Rosca <erosca@de.adit-jv.com>
Cc: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Cc: Sean Anderson <sean.anderson@seco.com>
Cc: Cody Schuffelen <schuffelen@google.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on vim3
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Currently BCB command-line, C APIs and implementation only
support MMC interface. Extend it to allow various block
device interfaces.
Signed-off-by: Dmitrii Merkurev <dimorinny@google.com>
Cc: Eugeniu Rosca <erosca@de.adit-jv.com>
Cc: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Cc: Sean Anderson <sean.anderson@seco.com>
Cc: Cody Schuffelen <schuffelen@google.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on vim3
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Now that we have time conversion defines from in time.h there is no need
for each driver to define their own version.
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com> # tegra
Reviewed-by: Eugen Hristev <eugen.hristev@collabora.com> #at91
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org> #qcom geni
Reviewed-by: Stefan Bosch <stefan_b@posteo.net> #nanopi2
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The description of the sysreset request method in <sysreset.h> says that
the return value should be -EPROTONOSUPPORT if the requested reset type
is not supported by this device.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Aligning addresses and sizes causes overhead which is unnecessary when we
are not loading from block devices. Remove bl_len when it is not needed.
For example, on iot2050 we save 144 bytes with this patch (once the rest of
this series is applied):
add/remove: 0/0 grow/shrink: 0/3 up/down: 0/-144 (-144)
Function old new delta
spl_load_simple_fit 920 904 -16
load_simple_fit 496 444 -52
spl_spi_load_image 384 308 -76
Total: Before=87431, After=87287, chg -0.16%
We use panic() instead of BUILD_BUG_ON in spl_set_bl_len because we still
need to be able to compile it for things like mmc_load_image_raw_sector,
even if that function will not be used.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
dev and priv serve the same purpose, and are never set at the same time.
Remove dev and convert all users to priv. While we're at it, reorder bl_len
to be last for better alignment.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To quote the author:
This series tests raw nand flash in sandbox and fixes various bugs discovered in
the process. I've tried to do things in a contemporary manner, avoiding the
(numerous) variations present on only a few boards. The test is pretty minimal.
Future work could test the rest of the nand API as well as the MTD API.
Bloat (for v1) at [1] (for boards with SPL_NAND_SUPPORT enabled). Almost
everything grows by a few bytes due to nand_page_size. A few boards grow more,
mostly those using nand_spl_loaders.c. CI at [2].
[1] https://gist.github.com/Forty-Bot/9694f3401893c9e706ccc374922de6c2
[2] https://source.denx.de/u-boot/custodians/u-boot-clk/-/pipelines/18443
Add a SPL test for the NAND load method. We use some different functions to
do the writing from the main test since things like nand_write_skip_bad
aren't available in SPL.
We disable BBT scanning, since scan_bbt is only populated when not in SPL.
We use nand_spl_loaders.c as it seems to be common to at least a few boards
already. However, we do not use nand_spl_simple.c because it would require
us to implement cmd_ctrl. The various nand load functions are adapted from
omap_gpmc. However, they have been modified for simplicity/correctness.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Add a sandbox NAND flash driver to facilitate testing. This driver supports
any number of devices, each using a single chip-select. The OOB data is
stored in-band, with the separation enforced through the API.
For now, create two devices to test with. The first is a very small device
with basic ECC. The second is an 8G device (chosen to be larger than 32
bits). It uses ONFI, with the values copied from the datasheet. It also
doesn't need too strong ECC, which speeds things up.
Although the nand subsystem determines the parameters of a chip based on
the ID, the driver itself requires devicetree properties for each
parameter. We do not derive parameters from the ID because parsing the ID
is non-trivial. We do not just use the parameters that the nand subsystem
has calculated since that is something we should be testing. An exception
is made for the ECC layout, since that is difficult to encode in the device
tree and is not a property of the device itself.
Despite using file I/O to access the backing data, we do not support using
external files. In my experience, these are unnecessary for testing since
tests can generally be written to write their expected data beforehand.
Additionally, we would need to store the "programmed" information somewhere
(complicating the format and the programming process) or try to detect
whether block are erased at runtime (degrading probe speeds).
Information about whether each page has been programmed is stored in an
in-memory buffer. To simplify the implementation, we only support a single
program per erase. While this is accurate for many larger flashes, some
smaller flashes (512 byte) support multiple programs and/or subpage
programs. Support for this could be added later as I believe some
filesystems expect this.
To test ECC, we support error-injection. Surprisingly, only ECC bytes in
the OOB area are protected, even though all bytes are equally susceptible
to error. Because of this, we take care to only corrupt ECC bytes.
Similarly, because ECC covers "steps" and not the whole page, we must take
care to corrupt data in the same way.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
NAND devices are destroyed in between unit tests. Provide a function to
reinitialize the subsystem at the beginning of each test.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
This performs the opposite of nand_register, allowing drivers to unregister
nand devices. This is probably unnecessary for most regular drivers, but we
expect sandbox drivers to get repeatedly bound/unbound, so this will help
avoid dangling pointers.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
This allows using these functions without ifdefs. OneNAND depends on MTD,
so this ifdef was redundant in the first place.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Rename SPL_MTD_SUPPORT to SPL_MTD in order to match MTD. This allows using
CONFIG_IS_ENABLED to test for MTD support.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Since commit 34793598c8 ("mtd: nand: mxs_nand_spl: Remove the page aligned
access") there are no longer any users of nand_get_mtd. However, it is
still important to know what the page size is so we can allocate a
large-enough buffer. If the image size is not page-aligned, we will go off
the end of the buffer and clobber some memory.
Introduce a new function nand_page_size which returns the page size. For
most drivers it is easy to determine the page size. However, a few need to
be modified since they only keep the page size around temporarily.
It's possible that this patch could cause a regression on some platforms if
the offset is non-aligned and there is invalid address space immediately
before the load address. spl_load_legacy_img does not (except when
compressing) respect bl_len, so only boards with SPL_LOAD_FIT (8 boards) or
SPL_LOAD_IMX_CONTAINER (none in tree) would be affected.
defconfig CONFIG_TEXT_BASE
======================= ================
am335x_evm 0x80800000
am43xx_evm 0x80800000
am43xx_evm_rtconly 0x80800000
am43xx_evm_usbhost_boot 0x80800000
am43xx_hs_evm 0x80800000
dra7xx_evm 0x80800000
gwventana_nand 0x17800000
imx8mn_bsh_smm_s2 0x40200000
All the sitara boards have DDR mapped at 0x80000000. gwventana is an i.MX6Q
which has DDR at 0x10000000. I don't have the IMX8MNRM handy, but on the
i.MX8M DDR starts at 0x40000000. Therefore all of these boards can handle a
little underflow.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
All other implementations of nand_spl_load_image only read as many pages as
are necessary to load the image. However, nand_spl_loaders.c loads the full
block. Align it with other load functions so that it is easier to
determine how large of a load buffer we need.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Contrary to what the help message says, this is the number of pages per
block. Calculate it automatically based on SYS_NAND_BLOCK_SIZE and
SYS_NAND_PAGE_SIZE. To better reflect its semantics, rename it to
SYS_NAND_BLOCK_PAGES.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
When no manufacturer is matched, manufacturer_desc is NULL. Avoid
dereferencing it in that case.
Fixes: 4e67c57125 ("mtd,ubi,ubifs: sync with linux v3.15")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
CONFIG_DM_WARN has a text indicating that these messages should only
provided when debugging. This implies that the setting must be default no.
We should still create debug messages.
Reported-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When building with AARCH64 defconfig, we got warnings, fix them
by using registers base address defined as void __iomem * instead of
fdt_addr_t.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The clk-pll.h is going to be included in multiple files soon. Add
missing header guard to prevent possible build errors in future.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Fixes: 166097e877 ("clk: exynos: add clock driver for Exynos7420 Soc")
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
clk_get_by_index() returns negative number on error. Assigning it to
unsigned int makes the subsequent "ret < 0" check always false, leading
in turn to possible unhandled errors. Change 'ret' variable type to
signed int so the code checks and handles clk_get_by_index() return code
properly.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Fixes: cf75cdf96e ("serial: s5p: use clock api to get clock rate")
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
s5p watchdog driver calls samsung_get_base_watchdog() function, but its
prototype is not included. That might lead to build warnings like this:
drivers/watchdog/s5p_wdt.c: In function 'wdt_stop':
drivers/watchdog/s5p_wdt.c:16:26:
warning: implicit declaration of function
'samsung_get_base_watchdog' [-Wimplicit-function-declaration]
16 | (struct s5p_watchdog *)samsung_get_base_watchdog();
| ^~~~~~~~~~~~~~~~~~~~~~~~~
Include asm/arch/cpu.h to fix that issue.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Currently the renesas_sdhi_reset_tuning() unconditionally leaves SDHI
clock enabled after the tuning reset. This is not always necessary.
After the driver performed tuning reset at the end of probe function,
or in the unlikely case that tuning failed during regular operation,
the SDHI clock can be disabled after the tuning reset. The following
set_ios call would reconfigure the clock as needed.
In case of regular set_ios call which requires a tuning reset, keep
the clock enabled or disabled according to the mmc->clk_disable state.
With this in place, the controllers which have not been accessed via
block subsystem after boot are left in quiescent state. However, if an
MMC device is used e.g. for environment storage, that controller would
be accessed during the environment load and left active, including its
clock which would still be generated. This is due to the design of the
MMC subsystem, which does not deinit a controller after it was started
once, the controller is only deinited in case of mmc rescan, or before
OS boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Tested-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Thuan Nguyen Hong <thuan.nguyen-hong@banvien.com.vn>
The X-Powers AXP313a is a small PMIC with just three buck converters and
three LDOs, one of which is actually fixed (so not modelled here).
Add the compatible string and the respective regulator ranges to allow
drivers to adjust voltages.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
On boards using the AXP313 PMIC, the DRAM rail is often not setup
correctly at reset time, so we have to program the PMIC very early in
the SPL, before running the DRAM initialisation.
Add a simple AXP313 PMIC driver that knows about DCDC2(CPU) and
DCDC3(DRAM), so that we can bump up the voltage before the DRAM init.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
sunxi platforms put .bss in DRAM, so .bss is not available in SPL before
DRAM controller initialization. Therefore, this buffer must be placed in
the .data section.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
commit 95168d77d3 ("sunxi: add Allwinner R528/T113 SoC support") added
the new entry out of order.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
CONFIG_ARCH_SUNXI will not be enabled for RISC-V SoCs using this driver.
Use the symbol for the driver itself instead.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
The MMC controller driver is (and ought to be) the only user of these
register definitions. Put them in a header next to the driver to remove
the dependency on a specific ARM platform's headers.
Due to the sunxi_mmc_init() prototype, the file was not renamed. None of
the register definitions were changed.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
DM_GPIO is always enable in U-Boot proper for ARCH_SUNXI, and this
driver is never enabled in SPL, so the condition is always true.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
So far we have a convoluted #ifdef mesh that guards the early AXP PMIC
setup in board.c. That combination of &&, || and negations is very hard
to read, maintain and especially to extend.
Fortunately we have those same conditions already modelled in the
Kconfig file, so they are actually redundant. On top of that the real
reason we have those preprocessor guards in the first place is about the
symbols that are *conditionally* defined: without #ifdefs the build
would break because of them being undefined for many boards.
To simplify this, just change the guards to actually look at the symbols
needed, so CONFIG_AXP_xxx_VOLT instead of CONFIG_AXPyyy_POWER.
This drastically improves the readability of this code, and makes adding
PMIC support a pure Kconfig matter.
Doing this revealed one bug in Kconfig: there is no axp_set_dcdc4() for
the AXP818, even though CONFIG_AXP_DCDC4_VOLT includes that PMIC.
Since the AXP818 wasn't included when calling axp_set_dcdc4() in board.c,
this wasn't an issue, but becomes one now, so also remove the AXP818 from
the DCDC4 Kconfig symbol.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
- Fix some issues Coverity has reported, update MAINTAINERS file,
another bootstd fix, typo fix in error message, gitignore fix and
update TI's URL in many places.
During bootstd scanning for bootdevs, if bootdev_hunt_drv() encounters
a device not found error (e.g. ENOENT), let it return a successful status
so that bootstd will continue scanning the next devices, not stopping
prematurely.
Background:
During scanning for bootflows, it's possible for bootstd to encounter a
faulty device controller. Also when the same u-boot is used for another
variant of the same board, some device controller such as SATA might
not exist.
I've found this issue while converting the Marvell Sheevaplug board to
use bootstd. This board has 2 variants, the original Sheevaplug has MMC and
USB only, but the later variant comes with USB, MMC, and eSATA ports. We
have been using the same u-boot (starting with CONFIG_IDE and later with DM
CONFIG_SATA) for both variants. This worked well with the old
envs-scripting booting scheme.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A power domain id on sandbox should be in the range from zero to
ARRAY_SIZE(scmi_pwdom) - 1. Correct the validity check logic.
Addresses-Coverity-ID: 467401 ("Out-of-bounds write")
Addresses-Coverity-ID: 467405 ("Out-of-bounds read")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
When we do not have CONFIG_BOUNCE_BUFFER enabled, inside of
scsi_init_dev_desc_priv we never set the 'bb' field to false, we only
initialize it to true when CONFIG_BOUNCE_BUFFER is set. Given that we
have a number of other fields here we had been explicitly setting to
zero, change to first calling memset to clear the struct and then
initialize only the fields that need non-zero default values.
Addresses-Coverity-ID: 467407 ("Uninitialized variables (UNINIT)")
Fixes: 81bd22e935 ("rockchip: block: blk-uclass: add bounce buffer flag to blk_desc")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Extend the otp driver to read rv1126 otp. This driver code was
adapted from the Rockchip BSP stack.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The migration deadline for moving to DM_SCSI was v2023.04. A further
reminder was sent out in August 2023 to the remaining platforms that had
not migrated already, and that a few more over the line (or configs
deleted).
With this commit we:
- Rename CONFIG_DM_SCSI to CONFIG_SCSI.
- Remove all of the non-DM SCSI code. This includes removing other
legacy symbols and code and removes some legacy non-DM AHCI code.
- Some platforms that had previously been DM_SCSI=y && SCSI=n are now
fully migrated to DM_SCSI as a few corner cases in the code assumed
DM_SCSI=y meant SCSI=y.
Signed-off-by: Tom Rini <trini@konsulko.com>
This file uses errno return values in functions, so include <errno.h>
here rather than rely on indirect inclusion.
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that sandbox has <asm/barrier.h> and defines nop() there we should
include that in our driver for clarity and then remove our local nop()
from <k210/pll.h>.
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Much of the functionality of fastboot relies on being able to run
commands as defined in the environment. This means it does depend on
CMDLINE being enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
While it is nice to have the font command, using 'select' makes it
impossible to build the console code without it. Stop using 'select' and
make it default if CONSOLE_TRUETYPE is enabled when asking the command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to do a DFU update over TFTP we need to have some network
device available, so make this depend on NETDEVICES
Signed-off-by: Tom Rini <trini@konsulko.com>
The following patch migrates the usage of debug and printf functions
to the relevant logging function as per U-Boot DM guidelines.
Additionally some of the debugging statements have been rearanged for
a more meaningfull debug experience.
aarch64-linux-gnu-size reports 229 bytes less when debug is enabled at
file level, while is just 5bytes more when disabled.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@amd.com>
Link: https://lore.kernel.org/r/20231013123739.2757979-1-ibai.erkiaga-elorza@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
When 64-bit address is passed only lower 32-bit address
is getting updated. Program the upper 32-bit address in the
DMA destination memory address MSBs register.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231011031515.4151-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Unhandled error coming from xilinx_pm_request() but return
value is not read back that's why getting sparse warning
as below:
warning: variable 'ret' set but not used [-Wunused-but-set-variable].
In case of error return the "ret" value.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231011025647.17200-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Provide an explicit configuration option to disable default "lock"
of any flash chip which supports locking. By disabling the lock
config will save some amount of memory and also don't expose the
lock functionality to the users i.e., via sf protect command.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231003031715.5343-2-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The baudrate configured in .config is taken by default by serial. If
change of baudrate is required then the .config needs to changed and
u-boot recompilation is required or the u-boot environment needs to be
updated.
To avoid this, support is added to fetch the baudrate directly from the
device tree file and update.
The serial, prints the log with the configured baudrate in the dtb.
The commit c4df0f6f31 ("arm: mvebu: Espressobin: Set default value for
$fdtfile env variable") is taken as reference for changing the default
environment variable.
The default environment stores the default baudrate value, When default
baudrate and dtb baudrate are not same glitches are seen on the serial.
So, the environment also needs to be updated with the dtb baudrate to
avoid the glitches on the serial.
Also add test to cover this new function.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230921112043.3144726-3-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Move the DEFAULT_ENV_IS_RW to Kconfig for easier configuration.
Hence, add the CONFIG_DEFAULT_ENV_IS_RW config to the defconfig files
to allow enabling them for armada boards.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230921112043.3144726-2-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
- sm fix to bind child sm devices in the device tree
- add missing A1 clocks for USB stack
-----BEGIN PGP SIGNATURE-----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=qtcH
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20231106' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- fixup to also enabled DFU RAM boot for libretech-ac
- sm fix to bind child sm devices in the device tree
- add missing A1 clocks for USB stack
One well-known sm child device that provides secure power control is the
Secure Power Controller. This device utilizes SMC calls to communicate
with power domains on the secure monitor side.
Signed-off-by: Dmitry Rokosov <ddrokosov@salutedevices.com>
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231101140500.9025-3-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Since we sync device tree with Linux, we have to add this
clock definition for USB stack.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231101140500.9025-2-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Older DesignWare Ethernet MAC versions that this driver supports can
only work with 32-bit DMA source/destination addresses. Some platforms
have no physical RAM at the lowest 4GB address space. For these
platforms the driver must translate DMA addresses to/from physical
memory addresses.
Call translation routines so that properly configured platforms can use
the DesignWare Ethernet MAC. For platforms using device-tree this
usually means adding dma-ranges property to the bus the device node is
in.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
e1000_eth_ids holds compatible strings for e1000 devices, but it
is meaningless as e1000 is a PCI device and there is no such
compatible string assigned to e1000 by the DT bindings community.
Drop it.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Setting the clock delay from the device tree settings
rx-internal-delay-ps and tx-internal-delay-ps was broken:
- The expected value in the device tree is suppose to be a
delay in picoseconds, but the driver only allowed an array index.
- Driver converted this array index to the actual delay in
picoseconds and tried to apply this in the device register. This
however is not a valid register value. The actual logic here was
reversed, it converted an register representation of the delay to
the device tree delay in picoseconds.
Only when the internal delays were NOT configured in the device tree
and they default value of 7 (=2000ps) was used, a valid value was
loaded in the register.
Signed-off-by: Frank de Brabander <debrabander@gmail.com>
It adds the driver for the internal MDIO bus of HIFEMAC Ethernet
controller. It's based on the mainstream linux driver.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
It adds the driver for HIFEMAC Ethernet controller found on HiSilicon
SoCs like Hi3798MV200. It's based on the mainstream linux driver, but
quite a lot of code gets rewritten and cleaned up to adopt u-boot driver
model.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Marvell LinkStreet switches support Clause 45 MDIO on the internal bus.
C45 read or writes require the register address to be written first to
the SMI PHY Data register, and then a special C45 Write Address Register
OP is used on the SMI PHY Register before making a C45 Read Data Register
OP and being able to actually read the register.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Driver is currently defining the mask and bit shifting itself,
there is no need for that as U-Boot has generic bitfield macros that help
us achieve the same result but in a cleaner way.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Add optional reset control, especially for the Aspeed SOC. For the
hardware without a reset line, the reset assertion/deassertion will be
skipped.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Set upper 32bit address for DMA descriptors and buffer address to support
64-bit addressing.
Signed-off-by: Ley Foon Tan <leyfoon.tan@starfivetech.com>
PALMAS PMIC family has embedded poweroff function used by some
device to initiane device power off. Implement it as sysreset
driver.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
TPS65910/TPS65911 PMICs have embedded power control functions
used by some device to initiane device power off. Implement it as
sysreset driver.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
TPS80031/TPS80032 PMICs have embedded power control functions
used by some device to initiane device power off. Implement it as
sysreset driver.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
MAX77663 PMIC has embedded poweroff function used by some
device to initiane device power off. Implement it as sysreset
driver.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Tegra uses built in Power Management Controller (PMC) to perform
CPU reset. Code to perform this was located in mach-tegra, so lest
create DM driver to handle this.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The driver provides regulator set/get voltage enable/disable
functions for TI TPS5911 PMIC.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support to bind the regulators/child nodes with the pmic.
Also adds the pmic i2c based read/write functions to access pmic
registers.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The driver provides regulator set/get voltage enable/disable
functions for TI TPS80031/TPS80032 PMICs.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support to bind the regulators/child nodes with the pmic.
Also adds the pmic i2c based read/write functions to access pmic
registers.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support to bind the regulators/child nodes with the pmic.
Also adds the pmic i2c based read/write functions to access pmic
registers.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
dev->driver_data will carry the tail of ldo if there is a number and
if there is no number it will be an error code, anyway it will not be
zero. This results in a wrong ldo regulator detection.
To avoid this check for non-numerical ldo first and then manipulate
dev->driver_data.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Existing PALMAS PMIC driver is fully compatible with TI TPS65913
PMIC found in many Tegra 4 devices, like Tegra Note 7 and ASUS
TF701T. TPS65913 shares same structure of regulators like TPS659038
so data can be reused.
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # NVIDIA Tegratab
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Default-tap and default-trim values are used for eMMC setup
mostly on T114+ devices. As for now, those values are hardcoded
for T210 and ignored for all other Tegra generations. Fix this
by passing tap and trim values from dts.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
on Peach-pi console every key press is echoed with message
'cros_ec_command: Returned status 1'
this is not proper fix, just hack to disable this message
Signed-off-by: Milan P. Stanić <mps@arvanta.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
i2c updates for v2024.01-rc2
- nuvoton: support standard/fast/fast plus mode
- bootcount: remove legacy i2c driver and implement
DM based version
Bugfixes:
- designware_i2c: adjust timing calculation
SPL probing failed on the StarFive VisionFive 2 board
Heinrich fixed this, by syncing timing calculation with
linux implementation.
+ CI: Use OpenSBI 1.3.1 release for testing
+ riscv: Support resume after exception
+ rng: Support RNG provided by RISC-V Zkr ISA extension
+ board: starfive VF2: Support jtag
+ board: starfive VF2: Support TRNG driver
+ board: sifive unmatched: Move kernel load address
In line with changes elsewhere, drop inclusion of the common header.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Adds to support JH7110 TRNG driver which is based on linux kernel's
jh7110-trng.c. This can support to generate 256-bit random numbers and
128-bit but this makes 256-bit default for convenience.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add STGCLK_SEC_HCLK and STGCLK_SEC_MISCAHB clocks for JH7110 TRNG
device.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The Zkr ISA extension (ratified Nov 2021) introduced the seed CSR. It
provides an interface to a physical entropy source.
A RNG driver based on the seed CSR is provided. It depends on
mseccfg.sseed being set in the SBI firmware.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This contains several fixes for the clock core.
-----BEGIN PGP SIGNATURE-----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=QToO
-----END PGP SIGNATURE-----
Merge tag 'clk-2024.01-rc2' of https://source.denx.de/u-boot/custodians/u-boot-clk
Clock changes for 2024.01-rc2
This contains several fixes for the clock core.
In clk_enable()/clk_disable() functions, when CCF is activated,
we must pass a private clk struct to enable()/disable() ops functions.
Otherwise, the use of a container_of() construction within these ops
should be banned. Because passing a non-private clk struct to
container_of() results in an out of range error.
At the moment, clk-mux, clk-fixed-factor, clk-gate and possibly other
clocks use container_of() in their enable()/disable() functions.
Therefore, for these functions to work correclty, private clk struct
must be passed.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20230905221649.3577929-1-bigunclemax@gmail.com
