Convert UTF-8 chars to ASCII in cases where make sense. No Copyright or
names are converted.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Marek Behún <kabel@kernel.org>
Move verdin-imx8mm and verdin-imx8mp to OF_UPSTREAM:
- handle the fact that dtbs now have a 'freescale/' prefix
- imply OF_UPSTREAM
- remove redundant files from arch/arm/dts leaving only the
*-u-boot.dtsi files
- update MAINTAINERS files
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
This event callback imx9_probe_mu needs to be called in board_r
as well, because many ELE APIs depending on this MU probed
Signed-off-by: Ye Li <ye.li@nxp.com>
The imx8mn-beacon boards can migrate to OF_UPSTREAM which also
allows for the removal the device tree files.
Signed-off-by: Adam Ford <aford173@gmail.com>
The imx8mm-beacon boards can migrate to OF_UPSTREAM which also
allows for the removal the device tree files.
Signed-off-by: Adam Ford <aford173@gmail.com>
The imx8mp-beacon boards can migrate to OF_UPSTREAM which also
allows for the removal the device tree files.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Add a weak default reset_cpu() implementation just like
it is done on arch/arm/mach-imx/cpu.c.
This allows the removal of the empty reset_cpu() in several
board files.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Hiago De Franco <hiago.franco@toradex.com> # Toradex Colibri iMX8X
This message is used to commit into the fuses any new SRK revocation and
FW version information that have been found into the NXP (ELE FW) and
OEM containers.
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Move to imx8m{m,n,p}-venice to OF_UPSTREAM:
- replace the non-upstream generic imx8m{m,n,p}-venice dt with one of the
dt's from the OF_LIST
- handle the fact that dtbs now have a 'freescale/' prefix
- imply OF_UPSTREAM
- remove rudundant files from arch/arm/dts leaving only the
*-u-boot.dtsi files
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
On imx8m[m|p|q].dtsi, upstream Linux uses different names for NPU/VPU
IP block nodes. It leads variants without such HW block having it
enabled by default.
This patch adds the upstream Linux node's paths to the disable list while
keep the compatibility with downstream Linux.
Signed-off-by: Vitor Soares <vitor.soares@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Use the latest, mx93a1-ahab-container.img that is compatible with the
i.MX93 A1 revision.
Using mx93a1-ahab-container.img on an A0 chip and conversely causes a boot
failure without any traces on the UART.
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Add support for booting the imxrt1050-evk from spi.
Add imximage config and the ability for SPL to boot from NOR.
Enable binman in Kconfig and device tree for imxrt* as it is used to
prepend fspi_header.bin to SPL and u-boot.img.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
The Sielaff i.MX6 Solo board is a control and HMI board for vending
machines. Add support for this board.
The devicetree files are taken from pending changes in the Linux
kernel that are available from linux-next and will likely be
part of Linux v6.9.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Commit d5eae216d8 ("net: dwc_eth_qos: Add board_interface_eth_init()
for i.MX93") implemented board_interface_eth_init for i.MX9 platforms.
However it only accounted for the EQOS interface while any board using
FEC as primary Ethernet interface was left out as return value -EINVAL
is always returned from the function in such case.
Fix this by returning 0 (success) when FEC interface is primarily used
instead of EQOS interface on i.MX93.
Fixes: d5eae216d8 ("net: dwc_eth_qos: Add board_interface_eth_init() for i.MX93")
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Tested-by: Mathieu Othacehe <m.othacehe@gmail.com>
The help for CONFIG_MTD explains that it needs to be enabled for various
things like NAND, etc to be available. It however then doesn't enforce
this dependency and so if you have none of these systems present you
still need to disable a number of options. Fix this by making places
that select/imply one type of flash, but did not do the same, also do
this for "MTD". Make boards which hadn't been enabling MTD already but
need it now, do so. In a few places, disable CONFIG_CMD_MTDPARTS as it
wasn't previously enabled but was now being implied.
Signed-off-by: Tom Rini <trini@konsulko.com>
In an attempt to select ARMV8_SPL_EXCEPTION_VECTORS, the SPL size
could not fit into the internal SRAM of some imx8m targets:
aarch64: + imx8mm_phg
+aarch64-linux-ld.bfd: u-boot-spl section `__u_boot_list' will not fit in region `.sram'
+aarch64-linux-ld.bfd: region `.sram' overflowed by 1824 bytes
Select LTO to prevent that.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Read i.MX9 CPU temp grade from fuses and fixup thermal trips in Linux
device-tree accordingly.
Based on commit 0543a1ed27 ("imx8m: fixup thermal trips")
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
All i.MX8M targets rely on using binman to generate the U-Boot
binary.
Select it at the SoC level instead of per board.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
All i.MX93 targets rely on using binman to generate the U-Boot
binary.
Select it at the SoC level instead of per board.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
- Removed fdt_addr from verdin-imx8mm to fix booting via bootefi.
- Support Ethernet PHY autodection on Data Modul i.MX8M Mini/Plus eDM
SBC
- Add i.MX93 binman support
- Add support for imx93-var-som
Add support for the Variscite VAR-SOM-IMX93 evaluation kit. The SoM
consists of an NXP iMX93 dual A55 CPU. The SoM is mounted on a Variscite
Symphony SBC.
Signed-off-by: Mathieu Othacehe <m.othacehe@gmail.com>
Add dedicated Makefile targets for the i.MX93 and a new imx93-u-boot.dtsi
device-tree to create binman images.
Signed-off-by: Mathieu Othacehe <m.othacehe@gmail.com>
Add PLL settings for DDR 3600 MTps . This is very similar to 3200 MTps
PLL setting, except the divider is not 9 but 8 .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Selecting CONFIG_IMX_HAB=y on a SPL target, such as apalis_imx6_defconfig,
for example, leads to the following build error:
/usr/bin/arm-linux-gnueabihf-ld.bfd: arch/arm/mach-imx/hab.o: in function `imx_hab_is_enabled':
arch/arm/mach-imx/hab.c:879: undefined reference to `fuse_read'
fuse_read() comes from SPL_MXC_OCOTP, which depends on SPL_DRIVERS_MISC,
since commit 251a3053b1 ("misc: imx: remove DM dependency for ocotp
driver in SPL").
Select SPL_DRIVERS_MISC in the SPL case to fix this build issue.
Reported-by: Lisandro Pérez Meyer <lpmeyer@ics.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Lisandro Pérez Meyer <lpmeyer@ics.com>
When CONFIG_DWC_ETH_QOS_IMX=y and CONFIG_FEC_MXC is not selected, the
following warning is seen:
arch/arm/mach-imx/imx8m/clock_imx8mm.c: In function 'board_interface_eth_init':
arch/arm/mach-imx/imx8m/clock_imx8mm.c:914:24: warning: implicit declaration of function 'imx8mp_fec_interface_init; did you mean 'imx8mp_eqos_interface_init'? [-Wimplicit-function-declaration]
Fix it by adding a stub for imx8mp_fec_interface_init() to handle this
case.
This follows the same approach done on imx8mp_eqos_interface_init().
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Add Variscite manufacturer to the IMX8MN_VAR_SOM target menu label as
the majority of targets include the manufacturer as part of their menu
description/label and it helps when looking for a particular
manufacturer/board.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add a common board_interface_eth_init() called by the DWC MAC driver to
setup the MAC <-> PHY interface according to the PHY mode obtained from
DT.
Remove the board-side configuration in the i.MX93 EVK files.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Change boot device logic to also allow environment stored in fat and
in ext4 when booting from SD or eMMC.
As the boot device check for SD and for eMMC was depending on
ENV_IS_IN_MMC being defined, change the ifdef blocks at
env_get_location to use IS_ENABLED instead for all modes, returning
NOWHERE when no valid mode is found.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Move an OEM closing logic to ahab_close() function to be able to use
it directly without calling a u-boot command.
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Add support for the Polyhex Debix Model A SBC board.
It is an industrial grade single board computer based on
NXP's i.MX 8M Plus.
Currently supported interfaces are:
- Serial console
- Micro SD
- eQOS and FEC Ethernet
imx8mp-debix-model-a.dts is taken from Linux 6.3.
Signed-off-by: Gilles Talis <gilles.talis@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This fixes a regression in the eMMC fast boot mode case where the buffer
was missing 464 bytes.
The code figures out how many bytes must at least be fetched to honor
the current read, rounds that up to the ss->pagesize [which is a no-op
in the USB download case because that has ->pagesize==1], fetches that
many bytes, but then recorded the original upper bound as the new end of
the valid data. However, this did not take into account the rounding up
to the ss->pagesize. Fix this by recording the actual bytes downloaded.
Fixes: 4b4472438f ("imx: spl_imx_romapi: avoid tricky use of spl_load_simple_fit() to get full FIT size")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Aligning addresses and sizes causes overhead which is unnecessary when we
are not loading from block devices. Remove bl_len when it is not needed.
For example, on iot2050 we save 144 bytes with this patch (once the rest of
this series is applied):
add/remove: 0/0 grow/shrink: 0/3 up/down: 0/-144 (-144)
Function old new delta
spl_load_simple_fit 920 904 -16
load_simple_fit 496 444 -52
spl_spi_load_image 384 308 -76
Total: Before=87431, After=87287, chg -0.16%
We use panic() instead of BUILD_BUG_ON in spl_set_bl_len because we still
need to be able to compile it for things like mmc_load_image_raw_sector,
even if that function will not be used.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Simplify things a bit for callers of spl_load_info->read by refactoring it
to use units of bytes instead of bl_len. This generally simplifies the
logic, as MMC is the only loader which actually works in sectors. It will
also allow further refactoring to remove the special-case handling of
filename. spl_load_legacy_img already works in units of bytes (oops) so it
doesn't need to be changed.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The migration deadline for moving to DM_SCSI was v2023.04. A further
reminder was sent out in August 2023 to the remaining platforms that had
not migrated already, and that a few more over the line (or configs
deleted).
With this commit we:
- Rename CONFIG_DM_SCSI to CONFIG_SCSI.
- Remove all of the non-DM SCSI code. This includes removing other
legacy symbols and code and removes some legacy non-DM AHCI code.
- Some platforms that had previously been DM_SCSI=y && SCSI=n are now
fully migrated to DM_SCSI as a few corner cases in the code assumed
DM_SCSI=y meant SCSI=y.
Signed-off-by: Tom Rini <trini@konsulko.com>
Similar change was done by commit b4c2c151b1 ("Kconfig: Remove all
default n/no options") and again sync is required.
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com> # tegra
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Angelo Dureghello <angelo@kernel-space.org>
