For successful reset staggering pulse operation, reset pulse
override bit is set. Port overcurrent bit 1, which in reality
reflects PIPE power present signal is set to avoid giving
false information of Vbus status to HPS controller.
Signed-off-by: Naresh Kumar Ravulapalli <nareshkumar.ravulapalli@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
This is for new platform enablement for Agilex7 M-series.
Add DDR driver for Agilex7 M-series. This driver is designed to support
DDR and HBM memory. The official HBM handoff is not ready yet, therefore
hardcoded handoff is used for HBM driver validation on mUDV board.
Signed-off-by: Tingting Meng <tingting.meng@altera.com>
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
SPL checks for a magic word in the system manager's scratch
register to determine if an L2 reset has occurred. If detected,
SPL places all slave CPUs (CPU1–3) into WFI mode. The master
CPU (CPU0) then initiates a warm reset by writing to the RMR_EL3
system register and also enters WFI mode.
This warm reset flow is handled entirely within the HPS. The
function `socfpga_sysreset_request()` triggers the warm
reset, and upon SPL re-entry, the updated `lowlevel_init_soc64.S`
handles the necessary initialization.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
The DDR data rate must be set correctly in the DDRIOCTRL
register according to the Actual Clock Frequency (ACF) value.
By enabling the reading of ACF value from bit 18 of the boot
scratch register during initialization, the DDR data rate is
able to be configured accurately.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
The boot scratch cold reg 8 is shared between DBE, DDR init progress
update and Linux EDAC. This patch defines how the bits are used by
respective features above and their macro names used in U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@altera.com>
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Initial creation of new system manager driver.
Add supports for the SOCFPGA System Manager Register block which
aggregates different peripheral function into one area.
On 64 bit ARM parts, the system manager only can be accessed during
EL3 mode, this driver model provide user the high level access
to system register and abstract user from low level access.
The base address of system manager can be retrieved
using DT framework through the System Manager driver.
Signed-off-by: Tien Fong Chee <tien.fong.chee@altera.com>
Signed-off-by: Boon Khai Ng <boon.khai.ng@altera.com>
This commit is to fix the system manager watchdog mode setting to support
until mode_4 for Agilex5. This changes can refer to system manager register
map on wddbg fields.
In Agilex7 it is not detected as an issue because Agilex7 only have 4 watchdog
until mode_3 and it is already been set correctly for it to halt on any CPU in
debug mode. However, in Agilex5 this fix is needed in order to enable the watchdog
pause feature for mode_4 when entering debug mode. If 0xF is not been set on mode_4,
the Watchdog Timers will not halt on any CPU. As by default value, the pause signal
does not assert when any CPU is in debug mode and the watchdog continue to count.
Signed-off-by: Muhammad Hazim Izzat Zamri <muhammad.hazim.izzat.zamri@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
The DDR subsystem in Diamond Mesa is consisted of controller, PHY,
memory reset manager and memory clock manager.
Configuration settings of controller, PHY and memory reset manager
is come from DDR handoff data in bitstream, which contain the register
base addresses and user settings from tool.
Configuration settings of memory clock manager is come from the HPS
handoff data in bitstream, however the register base address is defined
in device tree.
The calibration is fully done in HPS, which requires IMEM and DMEM
binaries loading to PHY SRAM for running this calibration, both
IMEM and DMEM binaries are also part of bitstream, this bitstream
would be loaded to OCRAM by SDM, and configured by DDR driver.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Changed to store QSPI reference clock in kHz instead of Hz in
boot scratch cold0 register for Stratix10 and Agilex.
This patch is in preparation for Intel N5X SDRAM driver
support. Reserved 4 bits for Intel N5X SDRAM driver,
and there will be 28 bits to store QSPI reference clock.
Due to limited bits, QSPI reference clock frequency is
converted to kHz from Hz.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Restructure Stratix10 and Agilex handoff code to used by
all SOC64 devices, in preparation to support handoff for
Diamond Mesa.
Remove wrap_pinmux_config_s10.c. Add wrap_handoff_soc64.c
which contains the generic function to parse the handoff
data.
Update system_manager_soc64.c to use generic handoff
function in wrap_handoff_soc64.c.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Document down the usage of boot_scratch_cold register to avoid
overlapping of usage in the code for S10 & Agilex.
The boot_scratch_cold register is generally used for passing
critical system info between SPL, U-Boot and Linux.
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Instead of querying SDM for FPGA configuration status through mailbox
messages, U-Boot now checks System Manager's FPGA Config status register
for FPGA configuration status before resetting bridge.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Move Stratix10 and Agilex system manager common code to
system_manager_soc64.h. Changed macros to use SYSMGR_SOC64_*.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
