The Indiedroid Nova is a Rockchip RK3588S based SBC from Indiedroid.
Specifications:
Rockchip RK3588S SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
4/8/16GB memory LPDDR4x
Mali G610MC4 GPU
Optional eMMC
2x USB 2.0, 2x USB 3.0, 1x USB 3.0 C port with DP Alt
1x MIPI-CSI Port (4-lane or 2x 2-lane)
1x MIPI-DSI 4-lane connector
1x Micro HDMI 2.1 output, 1x DP 1.4 output
Gigabit Ethernet
Realtek RTL8821CS WiFi
4 pin debug UART connector
40 pin GPIO header
Size: 85mm x 56mm (Raspberry Pi Form Factor)
Kernel commit:
3900160e164b ("arm64: dts: rockchip: Add Indiedroid Nova board")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Powkiddy X55 is a Rockchip RK3566 based handheld gaming device.
UART, ADC, eMMC, and SDMMC are tested to work in U-Boot and this
successfully boots mainline Linux.
Kernel commit:
e99adc97e21a ("arm64: dts: rockchip: Add Powkiddy X55")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sughosh Ganu <sughosh.ganu@linaro.org> says:
The following patch series adds support for version 2 of the FWU
metadata. The version 2 metadata structure is defined in the latest
revision of the FWU specification [1].
The earlier versions of these patches were migrating to a version 2
only support in U-Boot, similar to TF-A. However, based on feedback
from ST [2], this series has been updated to support both versions. A
platform would still be needed to enable one of the two versions of
metadata through a config symbol.
TF-A has code which reads the FWU metadata and boots the platform from
the active partition. TF-A has decided to migrate the FWU code to a
version 2 only support. These changes have been merged in upstream
TF-A.
These changes have been tested on the ST DK2 board, which uses the GPT
based partitioning scheme. Both V1 and V2 metadata versions have been
tested on the DK2 board.
These changes need to be tested on platforms with MTD partitioned
storage devices.
The FWU Update Agent in U-Boot supports both versions of the FWU
metadata. Make changes in the documentation to reflect this.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Tested-by: Michal Simek <michal.simek@amd.com>
Martyn Welch <martyn.welch@collabora.com> says:
This series adds DFU support for TI AM62 SK and beagleplay boards.
I have picked this series up from Sjoerd due to time constraints.
Since the last revision:
* Removed dwc3 mode setting in favour of reinstating forced peripheral
mode for usb0
* Use of config fragments for both r5 and a53 DFU configuration to
reduce duplication
* Typographical improvements to documentation
We plan to also submit the dts changes to linux so that those can be
dropped again in the near future (hopefully)
Both AM62 SK and beagleplay support DFU boot in a similar way now;
Document how to actually run DFU boot for both boards
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on beagle play
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Provide a man-page describing the usage of U-Boot on
the Milk-V Mars CM and Milk-V Mars CM Lite boards.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: E Shattow <lucent@gmail.com>
Add the CoolPi 4 Model B and CoolPi CM5 EVB board to the documentation.
Fixes: 3e15dee38d ("board: rockchip: Add support for rk3588 based Cool Pi CM5 EVB")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Simon Glass <sjg@chromium.org> says:
This series is the culmanation of the current line of refactoring
series. It adjusts pxe to call the booting functionality directly
rather than going through the command-line interface.
With this is is possible to boot using the extlinux bootmeth without
the command line enabled.
It also updates fastboot to do a similar thing.
Add instructions to build U-Boot for the Milk-V Mars board
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Currently in set_fdtfile() we set the value of environment variable fdtfile
unconditionally. The implies that a value in the environment will be
ignored.
With the patch environment variable fdtfile will only be set if it does not
yet exist. This requires that CONFIG_DEFAULT_FDT_FILE is not set.
Now the user can either set and save fdtfile interactively or in the U-Boot
configuration to overrule the device-tree name chosen based on the
hardware in set_fdtfile().
Reported-by: E Shattow <lucent@gmail.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Update and improve the building documentation of Apalis iMX8.
The following changes were made:
- imx-atf repository changed to nxp-imx GitHub.
- imx-atf branch updated to 'lf_v2.6'.
- imx-seco updated to version 5.8.7.
- nxp-imx mfgtools link updated to GitHub releases.
- General writing improvements.
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Update and improve the building documentation of Colibri iMX8X.
The following changes were made:
- imx-atf repository changed to nxp-imx GitHub.
- imx-atf branch updated to 'lf_v2.6'.
- imx-seco updated to version 5.8.7.
- nxp-imx mfgtools link updated to GitHub releases.
- General writing improvements.
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
- A new driver in the misc to register setting from device tree. This
also provides user a clean interface and all register settings are
centralized in one place, device tree.
- Enable Agilex5 platform for Intel product. Changes, modification and
new files are created for board, dts, configs and makefile to create
the base for Agilex5.
Build-tested on SoC64 boards, boot tested on some of them.
Please pull the updates for rockchip platform:
- Add board: rk3588 Generic, Cool Pi CM5, Theobroma-Systems RK3588 Jaguar SBC,
Toybrick TB-RK3588X;
rk3588s Cool Pi 4B;
rk3566 Pine64 PineTab2;
- Add saradc v2 support;
- Add PMIC RK806 support;
- rk3588 disable force_jtag by default;
- Migrate to use IO-domain driver for all boards;
- Use common bss and stack addresses for rk33xx and rk35xx boards;
- Other updates for driver, config and dts;
Add support to the RGxx3 device for the Powkiddy RGB10MAX3. This device
is extremely similar to all the other devices and can use the same
bootloader with the same detection logic.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 PineTab2 is a tablet computer based on the Rockchip RK3566
SoC. The table features 4/8 GB LPDDR4 RAM and 64/128 GB eMMC storage.
Features tested on a Pine64 PineTab2 8GB v2.0:
- SD-card boot
- eMMC boot
- SPI Flash boot
- USB host
Device tree is imported from linux maintainer branch v6.9-armsoc/dts64,
commit 1b7e19448f8f ("arm64: dts: rockchip: Add devicetree for Pine64
PineTab2").
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a minimal generic RK3588S/RK3588 board that only have eMMC and SDMMC
enabled. This defconfig can be used to boot from eMMC or SD-card on most
RK3588S/RK3588 boards that follow reference board design.
Also fix the alphabetical order of RK3588 boards listed in Makefile and
documentation.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
TB-RK3588X board is a Rockchip Toybrick RK3588 based development board.
Specification:
Rockchip Rk3588 SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
8/16GB Memory LPDDR4x
Mali G610MC4 GPU
2× MIPI-CSI0 Connector
1x 2Lanes PCIe3.0 Connector
1x SATA3.0 Connector
32GB eMMC Module
2x USB 2.0, 2x USB 3.0
1x HDMI Output, 1x HDMI Input
2x Ethernet Port
Functions work normally:
[1] USB2.0 Host
[2] Ethernet0 with PHY RTL8211F
More information can be obtained from the following websites:
[1] https://t.rock-chips.com/en/wiki/EN/tb-rk3588x_en/index.html
[2] http://t.rock-chips.com/
Kernel commits:
8ffe365f8dc7 ("arm64: dts: rockchip: Add devicetree support for TB-RK3588X board")
7140387ff49d ("dt-bindings: arm: rockchip: Add Toybrick TB-RK3588X")
Reviewed-by: Weizhao Ouyang <weizhao.ouyang@arm.com>
Signed-off-by: Elon Zhang <zhangzj@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3328-orangepi-r1-plus boards with new defaults.
Remove the SPL_DRIVERS_MISC=y option, no misc driver is used in SPL.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM. Also add LEGACY_IMAGE_FORMAT=y to keep
support for scripts.
Remove SPL_I2C=y and SPL_PMIC_RK8XX=y, the related i2c and pmic nodes is
not included in the SPL fdt.
Add CMD_GPIO=y and CMD_REGULATOR=y to add the helpful gpio and regulator
commands.
Add ROCKCHIP_EFUSE=y and remove NET_RANDOM_ETHADDR=y, ethaddr and
eth1addr is set based on cpuid read from eFUSE.
Add SPL_DM_SEQ_ALIAS=y option to use alias sequence number in SPL.
Add DM_ETH_PHY=y, PHY_GIGE=y, PHY_MOTORCOMM=y, PHY_REALTEK=y and remove
&gmac2io to support reset of onboard ethernet PHYs. Also add DM_MDIO=y
to ensure device tree props is used by motorcomm PHY driver.
Add PHY_ROCKCHIP_INNO_USB2=y option to support the onboard USB PHY.
Remove REGULATOR_PWM=y, the pwm-regulator compatible is not used.
Add RNG_ROCKCHIP=y and DM_RNG=y options to support the onboard random
generator.
Also add missing device tree files to MAINTAINERS file.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3328-nanopi-r2* boards with new defaults.
Remove the SPL_DRIVERS_MISC=y option, no misc driver is used in SPL.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM. Also add LEGACY_IMAGE_FORMAT=y to keep
support for scripts.
Remove SPL_I2C=y and SPL_PMIC_RK8XX=y, the related i2c and pmic nodes is
not included in the SPL fdt.
Add CMD_GPIO=y and CMD_REGULATOR=y to add the helpful gpio and regulator
commands.
Add ROCKCHIP_EFUSE=y and remove NET_RANDOM_ETHADDR=y, ethaddr and
eth1addr is set based on cpuid read from eFUSE.
Add SPL_DM_SEQ_ALIAS=y option to use alias sequence number in SPL.
Add DM_ETH_PHY=y, PHY_GIGE=y, PHY_MOTORCOMM=y, PHY_REALTEK=y and remove
&gmac2io to support reset of onboard ethernet PHYs. Also add DM_MDIO=y
to ensure device tree props is used by motorcomm PHY driver.
Remove REGULATOR_PWM=y, the pwm-regulator compatible is not used.
Add DM_REGULATOR_GPIO=y and SPL_DM_REGULATOR_GPIO=y to support the
regulator-gpio compatible.
Add RNG_ROCKCHIP=y and DM_RNG=y options to support the onboard random
generator.
Also add missing device tree files to MAINTAINERS file.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3328-rock-pi-e with new defaults.
Remove the xPL_DRIVERS_MISC=y option, no misc driver is used in xPL.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM. Also add LEGACY_IMAGE_FORMAT=y to keep
support for scripts.
Remove SPL_I2C=y and SPL_PMIC_RK8XX=y, the related i2c and pmic nodes is
not included in the SPL fdt.
Add CMD_GPIO=y and CMD_REGULATOR=y to add the helpful gpio and regulator
commands.
Add ROCKCHIP_EFUSE=y and remove NET_RANDOM_ETHADDR=y, ethaddr and
eth1addr is set based on cpuid read from eFUSE.
Add SPL_DM_SEQ_ALIAS=y option to use alias sequence number in SPL.
Add DM_MDIO=y to ensure device tree props can be used by PHY driver.
Remove REGULATOR_PWM=y, the pwm-regulator compatible is not used.
Add RNG_ROCKCHIP=y and DM_RNG=y options to support the onboard random
generator.
Also add myself as a reviewer for this board.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3328-roc-cc with new defaults.
Remove the SPL_DRIVERS_MISC=y option, no misc driver is used in SPL.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM. Also add LEGACY_IMAGE_FORMAT=y to keep
support for scripts.
Remove SPL_I2C=y and SPL_PMIC_RK8XX=y, the related i2c and pmic nodes is
not included in the SPL fdt.
Add CMD_GPIO=y and CMD_REGULATOR=y to add the helpful gpio and regulator
commands. Also add CMD_POWEROFF=y to be able to use the poweroff command.
Add ROCKCHIP_EFUSE=y and remove NET_RANDOM_ETHADDR=y, ethaddr and
eth1addr is set based on cpuid read from eFUSE.
Add SPL_DM_SEQ_ALIAS=y option to use alias sequence number in SPL.
Add DM_ETH_PHY=y, PHY_MOTORCOMM=y and PHY_REALTEK=y to support common
ethernet PHYs.
Remove REGULATOR_PWM=y, the pwm-regulator compatible is not used.
Add RNG_ROCKCHIP=y and DM_RNG=y options to support the onboard random
generator.
Also add missing device tree file to MAINTAINERS and add myself as a
reviewer for this board.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This migrates the plaintext README in
board/theobroma-systems/ringneck_px30 to doc/board/theobroma-systems and
while doing so, update the instructions and rewrite it in rST.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
This migrates the plaintext README in
board/theobroma-systems/puma_rk3399 to doc/board/theobroma-systems and
while doing so, update the instructions and rewrite it in rST.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Use proper binary artifact names for HSFS devices.
Do not use the *_unsigned binaries.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
TI K3 J784S4 and AM69 are new additions to the K3 SoC family.
Add documentation about the J784S4 EVM and AM69 SK.
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # AM69-SK
Use the latest, mx93a1-ahab-container.img that is compatible with the
i.MX93 A1 revision.
Using mx93a1-ahab-container.img on an A0 chip and conversely causes a boot
failure without any traces on the UART.
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
The MSM8916/APQ8016 Technical Reference Manual is publicly available and
contains a lot of useful register maps for many core parts of the SoC.
Include an archive.org link to it in the dragonboard410c documentation.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Replace the board specific docs with a generic board.rst file which
documents the build/boot process for the sdm845 and qcs404 boards now
that the only differences are the DTB in use.
At the same time, create a debugging page to document some useful
snippets and tips for working with Qualcomm platforms.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Sonoff iHost is gateway device designed to provide a Smart Home Hub,
it is based on Rockchip RV1126. There is also a version with 2GB RAM
based off the RV1109 dual core SoC however this works with the same
config as the RV1126 for uboot purposes.
Features:
- Rockchip RV1126
- 4GB DDR4
- 8GB eMMC
- microSD slot
- RMII Ethernet PHY
- 1x USB 2.0 Host
- 1x USB 2.0 OTG
- Realtek RTL8723DS WiFi/BT
- EFR32MG21 Silabs Zigbee radio
- Speaker/Microphone
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
