In case ENV_IS_IN_SPI_FLASH is disabled, returning ENVL_SPI_FLASH
leads to failure to find environment driver on start up. Fix this
by testing whether ENV_IS_IN_SPI_FLASH is enabled and if not, then
return ENVL_NOWHERE instead.
Signed-off-by: Marek Vasut <marex@denx.de>
The new i.MX8M Plus DHCOM rev.200 is populated with M24C32-D EEPROM
that contains an additional write-lockable page called ID page, which
is populated with a structure containing ethernet MAC addresses, DH
item number and DH serial number.
Because the write-lockable page is not present on rev.100 i.MX8MP DHCOM
SoM, test whether EEPROM ID page exists by setting up the i2c driver.
There may be multiple EEPROMs with an ID page on this platform, always
use the first one. The evaluation of the EEPROM ID page is done in two
steps. First, the content is read and checked. This is done to cache
the content of the EEPROM ID page. Second, the content is extracted
from the EEPROM buffer by requesting it.
For the ethernet MAC address the i.MX8M Plus DHCOM currently supports
parsing address from multiple sources in the following priority order:
1) U-Boot environment 'ethaddr'/'eth1addr' environment variable
2) SoC OTP fuses
3) On-SoM EEPROM
Add support for parsing the content of this new EEPROM ID page and place
it between 2) and 3) on the priority list. The new entry is 2.5) On-SoM
EEPROM write-lockable page.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Both regulators_enable_boot_on/off() are unused and superseded by
regulator uclass regulator_post_probe(). Remove both functions.
Signed-off-by: Marek Vasut <marex@denx.de>
U-Boot is currently unable to automatically enable regulators which
contain DT property regulator-always-on or regulator-boot-on. There
is an ongoing work to add this functionality to regulator core code,
but until the proper solution lands, add this awful workaround code
to force these regulators on. This is specifically needed to assure
the VIO regulator used to supply ethernet magnetics is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Check whether the ethernet interface is enabled at all before reading
MAC EEPROM. As a cost saving measure, it can happen that the MAC EEPROM
is not populated on SoMs which do not use ethernet.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Import DRAM timings generated by the DDR tool 3.31 which introduce assorted
tweaks to the DRAM controller settings. Furthermore, enable DBI to improve
noise resilience of the DRAM bus by reducing the number of bit changes on
the bus.
Reduce the DRAM rate to 3600 MTps to remove all remaining correctable errors
reported by EDAC . It is not entirely clear why the slightly faster setting
does produce sporadic correctable errors, while this one does not, but this
could be related to simpler PLL setting at 3600 MTps.
Enable inline ECC which is necessary to detect ECC errors and collect
statistics by the EDAC driver in Linux. This reduces the DRAM size by
64 MiB for each 512 MiB of DRAM, so for a 4 GiB device the available
DRAM size becomes 3.5 GiB and for 2 GiB device the available DRAM size
becomes 1.8 GiB.
Signed-off-by: Marek Vasut <marex@denx.de>
Add DT overlays to support additional DH i.MX8MP DHCOM SoM 660-100
population options with 1x or 2x RMII PHY mounted on PDK2 or PDK3
carrier boards.
Use SPL DTO support to apply matching SoM specific DTO to cater
for the SoM differences. Remove ad-hoc patching of control DT from
fdtdec_board_setup().
Signed-off-by: Marek Vasut <marex@denx.de>
The FEC interface mode is now configured in common board_interface_eth_init()
and called by FEC MAC driver when appropriate. Drop the board side duplicates
if the same functionality.
Signed-off-by: Marek Vasut <marex@denx.de>
The EQoS interface mode is now configured in common board_interface_eth_init()
and called by EQoS MAC driver when appropriate. Drop the board side duplicates
if the same functionality.
Signed-off-by: Marek Vasut <marex@denx.de>
The i.MX8MP DHCOM SoM may be populated with either KSZ9131RNXI RGMII PHY
or LAN8740Ai RMII PHY attached to EQoS MAC, and either external RGMII PHY
or LAN8740Ai RMII PHY attached to FEC MAC. The SoM configuration can be
detected for each MAC by reading RX_CTL pull resistor state early on boot.
Make use of this, detect the exact PHY configuration, and patch control DT
accordingly so that the ethernet is configured correctly in U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
To reduce code duplication, let the imx8 based DH boards use the common
code for setting up their MAC addresses.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Add support for DH electronics i.MX8M Plus DHCOM SoM on PDK2 carrier board.
Currently supported are serial console, EQoS and FEC ethernets, eMMC, SD,
SPI NOR and USB 3.0 host.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
