Quentin Schulz <foss+uboot@0leil.net> says:
This migrates the net options away from the main Kconfig to net/Kconfig,
rename the current NET option to NET_LEGACY to really highlight what it
is and hopefully encourage more people to use lwIP, add a new NET
menuconfig (but keep NO_NET as an alias to NET=n for now) which then
allows us to replace all the "if legacy_stack || lwip_stack" checks with
"if net_support" which is easier to read and maintain.
The only doubt I have is wrt SYS_RX_ETH_BUFFER which seems to be needed
for now even when no network is configured? Likely due to
include/net-common.h with PKTBUFSRX?
No change in behavior is intended. Only change in defconfig including
other defconfigs where NO_NET=y or NET is not set, in which case NO_NET
is not set or NET=y should be set in the top defconfig. Similar change
required for config fragments. See commit log in patch adding NET
menuconfig for details.
This was tested based on 70fd0c3bb7c2 ("x86: there is no
CONFIG_UBOOT_ROMSIZE_KB_12288"), from within the GitLab CI container
trini/u-boot-gitlab-ci-runner:noble-20251013-23Jan2026 and set up
similarly as in "build all platforms in a single job" GitLab CI job.
#!/usr/bin/env bash
set -o pipefail
set -eux
ARGS="-BvelPEWM --reproducible-builds --step 0"
./tools/buildman/buildman -o ${O} --force-build $ARGS -CE $*
./tools/buildman/buildman -o ${O} $ARGS -Ssd $*
O=../build/u-boot/ ../u-boot.sh -b master^..b4/net-kconfig |& tee ../log.txt
I can't really decipher the log.txt, but there's no line starting with
+ which would be an error according to tools/buildman/builder.py help
text. Additionally, because I started the script with set -e set and
because buildman has an exit code != 0 when it fails to build a board,
and I have the summary printed (which is the second buildman call), I
believe it means all builds passed.
The summary is the following:
aarch64: (for 537/537 boards) all +0.0 rodata +0.0
uniphier_v8 : all +1 rodata +1
u-boot: add: 0/0, grow: 1/0 bytes: 1/0 (1)
function old new delta
data_gz 10640 10641 +1
arm: (for 733/733 boards) all -0.0 rodata -0.0
uniphier_v7 : all -1 rodata -1
u-boot: add: 0/0, grow: 0/-1 bytes: 0/-1 (-1)
function old new delta
data_gz 11919 11918 -1
opos6uldev : all -3 rodata -3
u-boot: add: 0/0, grow: 0/-1 bytes: 0/-3 (-3)
function old new delta
data_gz 18778 18775 -3
uniphier_ld4_sld8: all -3 rodata -3
u-boot: add: 0/0, grow: 0/-1 bytes: 0/-3 (-3)
function old new delta
data_gz 11276 11273 -3
stemmy : all -20 rodata -20
u-boot: add: 0/0, grow: 0/-1 bytes: 0/-20 (-20)
function old new delta
data_gz 15783 15763 -20
As far as I could tell this data_gz is an automatically generated array
when CONFIG_CMD_CONFIG is enabled. It is the compressed .config stored
in binary form. Because I'm changing the name of symbols, replacing a
menu with a menuconfig, additional text makes it to .config and the
"# Networking" section in .config disappears.
Here is the diff for the 5 defconfigs listed above, generated with:
for f in build/*-m; do
diff --unified=0 $f/.config $(dirname $f)/$(basename -a -s '-m' $f)/.config
done
(-m is the build directory for master, and without the suffix, it's the
top commit of this series)
"""
--- build/opos6uldev-m/.config 2026-04-20 10:53:49.804528526 +0200
+++ build/opos6uldev/.config 2026-04-20 11:03:37.430242767 +0200
@@ -970,4 +969,0 @@
-
-#
-# Networking
-#
@@ -975,0 +972 @@
+CONFIG_NET_LEGACY=y
--- build/stemmy-m/.config 2026-04-20 11:01:33.653698123 +0200
+++ build/stemmy/.config 2026-04-20 11:04:53.452577311 +0200
@@ -733,4 +732,0 @@
-
-#
-# Networking
-#
@@ -738,2 +733,0 @@
-# CONFIG_NET is not set
-# CONFIG_NET_LWIP is not set
--- build/uniphier_ld4_sld8-m/.config 2026-04-20 11:00:41.605469071 +0200
+++ build/uniphier_ld4_sld8/.config 2026-04-20 11:04:22.226439899 +0200
@@ -997,4 +996,0 @@
-
-#
-# Networking
-#
@@ -1002,0 +999 @@
+CONFIG_NET_LEGACY=y
--- build/uniphier_v7-m/.config 2026-04-20 10:53:04.019307319 +0200
+++ build/uniphier_v7/.config 2026-04-20 11:03:01.688085486 +0200
@@ -1004,4 +1003,0 @@
-
-#
-# Networking
-#
@@ -1009,0 +1006 @@
+CONFIG_NET_LEGACY=y
--- build/uniphier_v8-m/.config 2026-04-20 10:43:05.614441175 +0200
+++ build/uniphier_v8/.config 2026-04-20 10:41:03.214852130 +0200
@@ -875,4 +874,0 @@
-
-#
-# Networking
-#
@@ -880,0 +877 @@
+CONFIG_NET_LEGACY=y
"""
This is fine:
- Networking menu doesn't exist anymore so "#\n# Networking\n#\n" won't
be in .config anymore.
- opos6uldev, uniphier_ld4_sld8, uniphier_v7 and uniphier_v8 all have
(old) CONFIG_NET enabled, (new) CONFIG_NET will still be set but
CONFIG_NET_LEGACY also needs to be defined now to reflect the stack
choice (even if default),
- stemmy has CONFIG_NO_NET set, which means CONFIG_NET and
CONFIG_NET_LWIP are not reachable anymore hence why they don't need to
be part of .config,
GitLab CI was run on this series (well, not exactly, but it's only
changes to the git logs that were made):
https://source.denx.de/u-boot/contributors/qschulz/u-boot/-/pipelines/29849
It passes.
Link: https://lore.kernel.org/r/20260420-net-kconfig-v1-0-9900002d8e72@cherry.de
Highlight that NET really is the legacy networking stack by renaming the
option to NET_LEGACY.
This requires us to add an SPL_NET_LEGACY alias to SPL_NET as otherwise
CONFIG_IS_ENABLED(NET_LEGACY) will not work for SPL.
The "depends on !NET_LWIP" for SPL_NET clearly highlights that it is
using the legacy networking app so this seems fine to do.
This also has the benefit of removing potential confusion on NET being a
specific networking stack instead of "any" network stack.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Change the SUPPORTS_FW_LOADER option to be enabled by default.
This is a dependency-only option intended to be used like:
depends on SUPPORTS_FW_LOADER
Instead of having to always remember to do both:
depends on CMDLINE
depends on ENV_SUPPORT
In order to actually work though, the option has to be enabled.
Reported-by: Weijie Gao <weijie.gao@mediatek.com>
Closes: https://lore.kernel.org/u-boot/20260410015311.4066075-1-weijie.gao@mediatek.com/
Fixes: 4ed440e6be80 ("fw_loader: Introduce SUPPORTS_FW_LOADER symbol")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Weijie Gao <weijie.gao@mediatek.com>
This symbol should not be enabled by the user directly but rather
selected when implemented in a given platform. This converts all of the
current users of this feature and hides the symbol.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to build this code, outside of QEMU systems which instead have
provided tables that we use, we must select ACPIGEN as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
The implementation of FW_LOADER requires CMDLINE to be enabled, and
expressses this. In order to not have to have every users also depends
on CMDLINE introduce SUPPORTS_FW_LOADER. This depends on CMDLINE and
ENV_SUPPORT and then we have all users depends on SUPPORTS_FW_LOADER.
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently, we have a copy of the LZMA SDK code, version 9.20, with small
updates. The original import of the LZMA SDK included a script to update the
library. This is no longer possible, due to important local changes, so
remove it. We also remove a number of extra text files that should be
unchanged from upstream, but provide no direct value to the project.
Instead, have the help text for LZMA note that this comes from the LZMA
SDK.
Next, we move our code up to the current release, 25.01. There are a
number of new header files, and some performance improvements made to
the code, at the cost of between 2 to 3 kilobytes in binary size. As
there is now a Kconfig option to disable this and retain similar speed
to what we have currently, the default option is to make this trade-off.
Our changes to the code around calling schedule() to avoid the watchdog
being triggered are kept. We add __UBOOT__ guards in two places to
prevent conflict with our own usage of these words on MIPS.
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently, our LZMA library has an option for optimizing for size,
rather than speed. It is a minimal savings today, and has not been worth
enabling. As this will change in the near future, add options now to
allow disabling it in full U-Boot or in SPL, and enable these on
gardena-smart-gateway-mt7688 which is very close to the size limit
today.
Reviewed-by: Stefan Roese <stefan.roese@mailbox.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The following functions are provided:
Count leading zero bits
* int __clzsi2 (unsigned int a)
* int __clzdi2 (unsigned long a)
* int __clzti2 (unsigned long long a)
Count trailing zero bits
* int __ctzsi2 (unsigned int a)
* int __ctzdi2 (unsigned long a)
* int __ctzti2 (unsigned long long a)
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Implement SM3_256 Hash algorithm, based on
linux commit f83a4f2a4d8c: ("Merge tag 'erofs-for-6.17-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs")
Therefore add the needed parts from linux.
Signed-off-by: Heiko Schocher <hs@nabladev.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The script based firmware loader does not use anything from the
fs_loader implementation. Separate it into its own library source
file and convert the mediatek PHY to use this separate code. This
should reduce the amount of code that is pulled in alongside the
firmware loader, as the FS loader is no longer included.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
We have a large number of library symbols that should not be prompted
for by the user really but rather selected by the platform (or SoC) as
needed. To start with however, make these depend on !COMPILE_TEST.
Signed-off-by: Tom Rini <trini@konsulko.com>
The generic name 'EFI' would be more useful for common EFI features. At
present it just refers to the EFI app and stub, which is confusing.
Rename it to EFI_CLIENT
Signed-off-by: Simon Glass <sjg@chromium.org>
Sean Edmond <seanedmond@microsoft.com> says:
In our datacenter application, a single DHCP server is servicing 36000+ clients.
Improvements are required to the DHCPv4 retransmission behavior to align with
RFC and ensure less pressure is exerted on the server:
- retransmission backoff interval maximum is configurable
(environment variable bootpretransmitperiodmax)
- initial retransmission backoff interval is configurable
(environment variable bootpretransmitperiodinit)
- transaction ID is kept the same for each BOOTP/DHCPv4 request
(not recreated on each retry)
For our application we'll use:
- bootpretransmitperiodmax=16000
- bootpretransmitperiodinit=2000
A new configuration BOOTP_RANDOM_XID has been added to enable a randomized
BOOTP/DHCPv4 transaction ID.
Enhance DHCPv4 sending/parsing option 209 (PXE config file). A previous
patch was accepted. A new patch fixes a possible double free() and
addresses latest review comments.
Link: https://lore.kernel.org/r/20240509023918.2504185-1-seanedmond@microsoft.com
This patch introduces 3 improvements to align with RFC 951:
- retransmission backoff interval maximum is configurable
- initial retranmission backoff interval is configurable
- transaction ID is kept the same for each BOOTP/DHCPv4 request
In applications where thousands of nodes are serviced by a single DHCP
server, maximizing the retransmission backoff interval at 2 seconds (the
current u-boot default) exerts high pressure on the DHCP server and
network layer.
RFC 951 “7.2. Client Retransmission Strategy” states that the
retransmission backoff interval should be limited to 60 seconds. This
patch allows the interval to be configurable using the environment
variable "bootpretransmitperiodmax"
The initial retranmission backoff period defaults to 250ms, which is
also too small for these scenarios with many clients. This patch makes
the initial retransmission interval to be configurable using the
environment variable "bootpretransmitperiodinit".
Also, on a retransmission it is not expected for the transaction ID to
change (only the 'secs' field should be updated). Let's save the
transaction ID and use the same transaction ID for each BOOTP/DHCPv4
exchange.
Signed-off-by: Sean Edmond <seanedmond@microsoft.com>
The formatting with %pa / %pap behaves like %x, which results in an
incorrect value being output. To improve this, a new fine-tuning
Kconfig SPL_USE_TINY_PRINTF_POINTER_SUPPORT for pointer formatting
has been added. If it is enabled, the output of %pa / %pap should
be correct, and if it is disabled, the pointer formatting is
completely unsupported. In addition to indicate unsupported formatting,
'?' will be output. This allows enabling pointer formatting only
when needed. For SPL_NET it is selected by default. Then it also
supports the formatting with %pm, %pM and %pI4.
In summery this level of %p support for tiny printf is possible now:
1) The standard tiny printf won't have support for pointer formatting.
So it doesn't print misleading values for %pa, instead '?' will be
output:
%p => ?
%pa => ?a
%pap => ?ap
2) If SPL_USE_TINY_PRINTF_POINTER_SUPPORT is enabled or DEBUG is defined
tiny printf supports formatting %p and %pa / %pap.
3) If SPL_NET is enabled the support of pointers is extended
for %pm, %pM and %pI4.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Add a new internal API called uthread (Kconfig symbol: UTHREAD) which
provides cooperative multi-tasking. The goal is to be able to improve
the performance of some parts of U-Boot by overlapping lengthy
operations, and also implement background jobs in the U-Boot shell.
Each uthread has its own stack allocated on the heap. The default stack
size is defined by the UTHREAD_STACK_SIZE symbol and is used when
uthread_create() receives zero for the stack_sz argument.
The implementation is based on context-switching via initjmp()/setjmp()/
longjmp() and is inspired from barebox threads [1]. A notion of thread
group helps with dependencies, such as when a thread needs to block
until a number of other threads have returned.
The name "uthread" comes from "user-space threads" because the
scheduling happens with no help from a higher privileged mode, contrary
to more complex models where kernel threads are defined. But the 'u'
may as well stand for 'U-Boot' since the bootloader may actually be
running at any privilege level and the notion of user vs. kernel may
not make much sense in this context.
[1] https://github.com/barebox/barebox/blob/master/common/bthread.c
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Since commit 53d5a221632e ("emulation: Use bloblist to hold tables")
`make qemu-riscv64_smode_defconfig acpi.config && make` fails with
qfw_acpi.c:146:(.text.evt_write_acpi_tables+0xc):
undefined reference to `bloblist_add'
Build with bloblist support.
Fixes: 53d5a221632e ("emulation: Use bloblist to hold tables")
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
We have three warnings about needing to use quotes around some strings
in Kconfig files today. In two of these cases we can just add the
missing strings. In the case of INTEL_PINCTRL_PADCFG_PADTOL the symbol
is never referenced and should be dropped.
Signed-off-by: Tom Rini <trini@konsulko.com>
CONFIG_SYS_FDT_PAD defines the number of unused bytes added to a
device-tree and not the total size.
Fixes: 40ed7be4af52 ("Convert CONFIG_SYS_FDT_PAD to Kconfig")
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This code is not necessarily needed in VPL, even if SPL uses it, so
adjust the rules to allow it to be dropped.
Do the same for the hash API.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add PCR allocate wrapper APIs for using in tcg2 protocol.
The wrapper proceeds a PCR allocate command, followed by a
shutdown command.
A system boot is required after two commands since TPM device needs
a HW reset to activate the new algorithms config.
Also, a helper function is included to determine the new bank mask
for PCR allocation by combining the status of current active,
supported and eventlog bank masks.
A new kconfig is created. PCR allocate and system reboot only
happens when the kconfig is selected, otherwise just exit with
errors.
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
QEMU can have its own internal ACPI and SMBIOS tables. At present U-Boot
copies out the SMBIOS tables but points directly to the ACPI ones.
The ACPI tables are not aligned on a 4KB boundary, which means that UPL
cannot use them directly, since it uses a reserved-memory node for the
tables and that it assumed (by EDK2) to be 4KB-aligned.
On x86, QEMU provides the tables in a mapped memory region and U-Boot
makes use of these directly, thus making it difficult to use any common
code.
Adjust the logic to fit within the existing table-generation code. Use a
bloblist always and ensure that the ACPI tables is placed in an aligned
region. Set a size of 8K for QEMU. This does not actually put all the
tables in one place, for QEMU, since it currently adds a pointer to the
tables in QFW.
On ARM, enable bloblist so that SMBIOS tables can be added to the
bloblist.
Signed-off-by: Simon Glass <sjg@chromium.org>
Raymond Mao <raymond.mao@linaro.org> says:
Motivations for changes:
Current SMBIOS library and command-line tool is not fully matching with
the requirements:
1. Missing support for other mandatory types (#7, #9, #16, #17, #19).
2. Only a few platforms support SMBIOS node from the device tree.
3. Values of some fields are hardcoded in the library other than fetching
from the device hardware.
4. Embedded data with dynamic length is not supported (E.g. Contained
Object Handles in Type #2 and Contained Elements in Type #3)
Changes:
1. Refactor the SMBIOS library and command-line tool to better align with
the SMBIOS spec.
2. Create an arch-specific driver for all aarch64-based platforms to fetch
SMBIOS private data from the device hardware (processor and cache).
3. Create a sysinfo driver to poppulate platform SMBIOS private data.
4. Add generic SMBIOS DTS file for arm64 platforms for those common strings
and values which cannot be retrieved from the system registers.
Vendors can create their own SMBIOS node using this as an example.
For those boards without SMBIOS nodes, this DTS file can be included to
have a generic SMBIOS information of the system.
5. Add support for Type #7 (Cache Information) and link its handles to
Type #4.
6. To minimize size-growth for those platforms which have not sufficient
ROM spaces or the platforms which don't need detailed SMBIOS
information, new added fields are only being built when kconfig
GENERATE_SMBIOS_TABLE_VERBOSE is selected.
Once this patch is acceptted, subsequent patch sets will add other missing
types (#9, #16, #17, #19).
Tests:
To test this with QEMU arm64, please follow the guide on dt_qemu.rst to
get a merged DT to run with.
```
qemu-system-aarch64 -machine virt -machine dumpdtb=qemu.dtb
cat <(dtc -I dtb qemu.dtb) <(dtc -I dtb ./dts/dt.dtb | grep -v /dts-v1/) \
| dtc - -o merged.dtb
qemu-system-aarch64 -machine virt -nographic -bios u-boot.bin \
-dtb merged.dtb
```
Link: https://lore.kernel.org/r/20241206225438.13866-1-raymond.mao@linaro.org
Current smbios library does not fully match to the specification.
It hardcodes values instead of exposing values from the device.
It does not reserve the space to support dynamic length for
contained object handles or elements and misses the handling of
a few of fields.
The refactoring of this patch includes:
1. Expose values from device via sysinfo interface.
2. Replace smbios_add_prop with smbios_add_prop_si to allow getting
string values from sysinfo.
3. Add smbios_get_val_si to get values from sysinfo or device tree.
4. Use sysinfo_get_data to get data area.
5. Reserve the space of contained object handles and elements.
6. Miscellaneous fixes in smbios.
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
This reverts commit 1fdf53ace13f745fe8ad4d2d4e79eed98088d555, reversing
changes made to e5aef1bbf11412eebd4c242b46adff5301353c30.
I had missed that this caused too much size growth on rcar3_salvator-x.
Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Glass <sjg@chromium.org> says:
This includes various patches towards implementing the VBE abrec
bootmeth in U-Boot. It mostly focuses on SPL tweaks and adjusting what
fatures are available in VPL.
Link: https://lore.kernel.org/r/20241207172412.1124558-1-sjg@chromium.org
Adding binman node with target images description can be unwanted feature
but as of today there is no way to disable it.
Also on size constrained systems it is not useful to add binman description
to DTB.
Introduce BINMAN_DTB Kconfig symbol which allows separate DTB for target
from DTB for binman itself.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/f1379d2587f9bf279a7a75c318aabbc1b35ee0c6.1730452668.git.michal.simek@amd.com
Patrick Rudolph <patrick.rudolph@9elements.com> says:
Based on the existing work done by Simon Glass this series adds
support for booting aarch64 devices using ACPI only.
As first target QEMU SBSA support is added, which relies on ACPI
only to boot an OS. As secondary target the Raspberry Pi4 was used,
which is broadly available and allows easy testing of the proposed
solution.
The series is split into ACPI cleanups and code movements, adding
Arm specific ACPI tables and finally SoC and mainboard related
changes to boot a Linux on the QEMU SBSA and RPi4. Currently only the
mandatory ACPI tables are supported, allowing to boot into Linux
without errors.
The QEMU SBSA support is feature complete and provides the same
functionality as the EDK2 implementation.
The changes were tested on real hardware as well on QEMU v9.0:
qemu-system-aarch64 -machine sbsa-ref -nographic -cpu cortex-a57 \
-pflash secure-world.rom \
-pflash unsecure-world.rom
qemu-system-aarch64 -machine raspi4b -kernel u-boot.bin -cpu cortex-a72 \
-smp 4 -m 2G -drive file=raspbian.img,format=raw,index=0 \
-dtb bcm2711-rpi-4-b.dtb -nographic
Tested against FWTS V24.03.00.
Known issues:
- The QEMU rpi4 support is currently limited as it doesn't emulate PCI,
USB or ethernet devices!
- The SMP bringup doesn't work on RPi4, but works in QEMU (Possibly
cache related).
- PCI on RPI4 isn't working on real hardware since the pcie_brcmstb
Linux kernel module doesn't support ACPI yet.
Link: https://lore.kernel.org/r/20241023132116.970117-1-patrick.rudolph@9elements.com
On Arm platforms that use ACPI they cannot rely on the "spin-table"
CPU bringup usually defined in the FDT. Thus implement the
'ACPI Multi-processor Startup for ARM Platforms', also referred to as
'ACPI parking protocol'.
The ACPI parking protocol works similar to the spin-table mechanism, but
the specification also covers lots of shortcomings of the spin-table
implementations.
Every CPU defined in the ACPI MADT table has it's own 4K page where the
spinloop code and the OS mailbox resides. When selected the U-Boot board
code must make sure that the secondary CPUs enter u-boot after relocation
as well, so that they can enter the spinloop code residing in the ACPI
parking protocol pages.
The OS will then write to the mailbox and generate an IPI to release the
CPUs from the spinloop code.
For now it's only implemented on ARMv8, but can easily be extended to
other platforms, like ARMv7.
TEST: Boots all CPUs on qemu-system-aarch64 -machine raspi4b
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Allow to use BLOBLIST_TABLES on arm to store ACPI or other tables.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
The EFI_CONVENTIONAL_MEMORY type is now being managed through the LMB
module. Add a separate function, lmb_arch_add_memory() to add the RAM
memory to the LMB memory map. The efi_add_known_memory() function is
now used for adding any other memory type to the EFI memory map.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
The EFI memory allocations are now being done through the LMB module,
and hence the memory map is maintained by the LMB module. Use the
lmb_arch_add_memory() API function to add the usable RAM memory to the
LMB's memory map.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Some architectures have special or unique aspects which need
consideration when adding memory ranges to the list of available
memory map. Enable this config in such scenarios which allow
architectures and boards to define their own memory map.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Port mbedtls with adapted libc header files.
Add mbedtls default config header file.
Optimize mbedtls default config by disabling unused features to
reduce the target size.
Add mbedtls kbuild makefile.
Add Kconfig skeleton and config submenu entry for selecting
crypto libraries between mbedtls and legacy ones.
Add the mbedtls include directories into the build system.
Port u-boot hash functions as MbedTLS crypto alternatives and set
it as default.
Subsequent patches will separate those Kconfigs into pairs of
_LEGACY and _MBEDTLS for controlling the implementations of legacy
crypto libraries and MbedTLS ones respectively.
The motivation of moving and adapting *INT* macros from kernel.h
to limits.h is to fulfill the MbedTLS building requirement.
The conditional compilation statements in MbedTLS expects the
*INT* macros as constant expressions, thus expressions like
`((int)(~0U >> 1))` will not work.
Prerequisite
------------
This patch series requires mbedtls git repo to be added as a
subtree to the main U-Boot repo via:
$ git subtree add --prefix lib/mbedtls/external/mbedtls \
https://github.com/Mbed-TLS/mbedtls.git \
v3.6.0 --squash
Moreover, due to the Windows-style files from mbedtls git repo,
we need to convert the CRLF endings to LF and do a commit manually:
$ git add --renormalize .
$ git commit
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Add support for generating version 5 UUIDs, these are determistic and work
by hashing a "namespace" UUID together with some unique data. One intended
usecase is to allow for dynamically generate payload UUIDs for UEFI
capsule updates, so that supported boards can have their own UUIDs
without needing to hardcode them.
In addition, move the common bit twiddling code from gen_ran_uuid into a
separate function and rewrite it not to use clrsetbits (which is not
available when building as part of host tools).
Tests for this are added in an upcoming patch.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The EFI_LOADER and EFI config options are randomly scattered under lib/
making it cumbersome to navigate and enable options, unless you really
know what you are doing. On top of that the existing options are in
random order instead of a logical one.
So let's move things around a bit and move them under boot/. Present a
generic UEFI entry where people can select Capsules, Protocols,
Services, and an option to compile U-Boot as an EFI for X86
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The TCG event log buffer is being set at the end of ram memory. This
region of memory is to be reserved as LMB_NOMAP memory in the LMB
memory map. The current location of this buffer overlaps with the
memory region reserved for the U-Boot image, which is at the top of
the usable memory. This worked earlier as the LMB memory map was not
global but caller specific, but fails now because of the overlap.
Move the TCG event log buffer to the start of the ram memory region
instead. Move the location of the early trace buffer and the load
buffer for U-Boot(spl boot) accordingly.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
All the current function definitions of arch_lmb_reserve() are doing
the same thing -- reserve the U-Boot memory region. The powerpc(ppc)
architecture, in addition, is making some LMB reservations for the
bootm related image loading. Move these ppc specific reservations to
the arch_misc_init() function. This allows to move the U-Boot memory
region reservation to a different function, and remove
arch_lmb_reserve() in a subsequent commit.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add separate config symbols for enabling the LMB module for the SPL
phase. The LMB module implementation now relies on alloced list data
structure which requires heap area to be present. Add specific config
symbol for the SPL phase of U-Boot so that this can be enabled on
platforms which support a heap in SPL.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The LMB memory maps are now being maintained through a couple of
alloced lists, one for the available(added) memory, and one for the
used memory. These lists are not static arrays but can be extended at
runtime. Remove the config symbols which were being used to define the
size of these lists with the earlier implementation of static arrays.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Simon reports that after enabling all algorithms on the TPM some boards
fail since they don't have enough storage to accommodate the ~5KB growth.
The choice of hash algorithms is determined by the platform and the TPM
configuration. Failing to cap a PCR in a bank which the platform left
active is a security vulnerability. It might allow unsealing of secrets
if an attacker can replay a good set of measurements into an unused bank.
If MEASURED_BOOT or EFI_TCG2_PROTOCOL is enabled our Kconfig will enable
all supported hashing algorithms. We still want to allow users to add a
TPM and not enable measured boot via EFI or bootm though and at the same
time, control the compiled algorithms for size reasons.
So let's add a function tpm2_allow_extend() which checks the TPM active
PCRs banks against the one U-Boot was compiled with. We only allow
extending PCRs if the algorithms selected during build match the TPM
configuration.
It's worth noting that this is only added for TPM2.0, since TPM1.2 is
lacking a lot of code at the moment to read the available PCR banks.
We unconditionally enable SHA1 when a TPM is selected, which is the only
hashing algorithm v1.2 supports.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook-link
All errors are generated by ./tools/qconfig.py -b -j8 -i whatever.
Error look like this:
drivers/crypto/Kconfig:9: warning: style: quotes recommended around
'drivers/crypto/nuvoton/Kconfig' in 'source drivers/crypto/nuvoton/Kconfig'
Signed-off-by: Michal Simek <michal.simek@amd.com>
The README.trace has been moved and converted to rst in commit dce26c7d56ed
("doc: move README.trace to HTML documentation"); fix all the remaining
references to this file.
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
