With CONFIG_OF_LIVE=y, dev_of_offset(dev) does not return a valid
flat-FDT offset, so fdtdec_get_int(gd->fdt_blob, offset, ...) inside
gen_74x164_probe() fails to locate the "registers-number" property and
always falls back to the default value of 1. This results in a 4-chip
74HC595 daisy chain being exposed as only 8 GPIOs instead of 32, and
any consumer referencing offsets >= 8 fails to bind with -ENOENT
("GPIO ... not found" / Error -22).
The "registers-default" property is ignored for the same reason, so
any configured power-on output pattern is silently discarded.
Replace the flat-FDT helpers with dev_read_u32_default() and
dev_read_u8_array_ptr(), which correctly walk both live and flat
trees. This matches how other DM GPIO drivers (e.g. pca953x_gpio.c)
read their per-device properties.
With gd->fdt_blob no longer referenced, also drop the now-unused
DECLARE_GLOBAL_DATA_PTR and <asm/global_data.h> include.
Tested on stm32mp153d-ssonic (CONFIG_OF_LIVE=y) with a 4-chip 74HC595
chain: all 32 GPIOs are now exposed, and 16 consumer LED nodes at
offsets 0..31 bind successfully.
Fixes: 9300f711baac ("dm: gpio: introduce 74x164 driver")
Signed-off-by: Chanhong Jung <happycpu@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The GPIOs on PM7550 work fine using the qcom_spmi_gpio driver and
enables the use of the Volume Up button on the Fairphone (Gen. 6)
smartphone.
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://patch.msgid.link/20260318-milos-bringup-v2-5-650b91dd75d8@fairphone.com
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
This provides GPIO support over SCMI. It is built on top of the
pinctrl-scmi driver. A typical device tree entry might look like
this:
gpio1 {
compatible = "scmi-pinctrl-gpio";
gpio-controller;
#gpio-cells = <2>;
ngpios = <10>;
gpio-ranges = <&scmi_pinctrl 0 8 4>,
<&scmi_pinctrl 4 12 1>,
<&scmi_pinctrl 5 15 1>,
<&scmi_pinctrl 6 17 4>;
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins>;
};
In this GPIO driver the one thing which is different is that in the
gpio-ranges the first numbers which represent how the pins are exposed
to the users have to start at zero and it can't have gaps.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The legacy CMD_PCA953X command can only be built when the matching
legacy driver is enabled, add that dependency to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
After years of developing the ADI ADSP platform, Timesys was purchased
by another company and is no longer contracted to maintain the platform.
Signed-off-by: Philip Molloy <philip.molloy@analog.com>
Reviewed-by: Greg Malysa <malysagreg@gmail.com>
The hardware denies any access from the U-Boot non-secure world to the
secure-protected pins. Hence, prevent any driver to request such a pin.
Signed-off-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Peng Fan (OSS) <peng.fan@oss.nxp.com> says:
This patch set primarily removes unused DECLARE_GLOBAL_DATA_PTR
instances.
Many files declare DECLARE_GLOBAL_DATA_PTR and include
asm/global_data.h even though gd is never used. In these cases,
asm/global_data.h is effectively treated as a proxy header, which is
not a good practice.
Following the Include What You Use principle, files should include
only the headers they actually depend on, rather than relying on
global_data.h indirectly. This approach is also adopted in Linux kernel
[1].
The first few patches are prepartion to avoid building break after
remove the including of global_data.h.
A script is for filtering the files:
list=`find . -name "*.[ch]"`
for source in ${list}
do
result=`sed -n '/DECLARE_GLOBAL_DATA_PTR/p' ${source}`
if [ "${result}" == "DECLARE_GLOBAL_DATA_PTR;" ]; then
echo "Found in ${source}"
result=`sed -n '/\<gd\>/p' ${source}`
result2=`sed -n '/\<gd_/p' ${source}`
result3=`sed -n '/\<gd->/p' ${source}`
if [ "${result}" == "" ] && [ "${result2}" == "" ] && [ "${result3}" == "" ];then
echo "Cleanup ${source}"
sed -i '/DECLARE_GLOBAL_DATA_PTR/{N;/\n[[:space:]]*$/d;s/.*\n//;}' ${source}
sed -i '/DECLARE_GLOBAL_DATA_PTR/d' ${source}
sed -i '/global_data.h/d' ${source}
git add ${source}
fi
fi
done
[1] https://lpc.events/event/17/contributions/1620/attachments/1228/2520/Linux%20Kernel%20Header%20Optimization.pdf
CI: https://github.com/u-boot/u-boot/pull/865
Link: https://lore.kernel.org/r/20260209-cleanup-v2-0-73a3a84ddbdb@nxp.com
Remove DECLARE_GLOBAL_DATA_PTR from files where gd is not used, and
drop the unnecessary inclusion of asm/global_data.h.
Headers should be included directly by the files that need them,
rather than indirectly via global_data.h.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> #STMicroelectronics boards and STM32MP1 ram test driver
Tested-by: Anshul Dalal <anshuld@ti.com> #TI boards
Acked-by: Yao Zi <me@ziyao.cc> #TH1520
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add a GPIO controller driver that provides configurable delays when
setting GPIO output values. This is useful for hardware that requires
specific timing delays during power sequencing or GPIO state changes.
The driver wraps underlying GPIO controllers and adds programmable
ramp-up and ramp-down delays specified in microseconds through the
device tree. Each GPIO can have independent delay timings.
Device tree binding matches Linux.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/575998efc6ba0e405640789cf8d05f0b633f496e.1770105146.git.michal.simek@amd.com
Tom Rini <trini@konsulko.com> says:
As seen by a number of patches fixing memory leaks, U-Boot has a problem
with developer expectations around devm_kmalloc and friends. Namely,
whereas in Linux these memory allocations will be freed automatically in
most cases, in U-Boot this is only true if DEVRES is enabled. Now,
intentionally, in xPL phases, we do not (and do not offer as an option)
enabling DEVRES. However in full U-Boot this is left either to the user,
or some drivers have select'd DEVRES on their own. This inconsistency is
a problem. This series goes and deals with two small issues that were
shown by having all drivers that use devm_.alloc to allocate memory also
select DEVRES and then we make DEVRES no longer be a prompted option and
instead select'd as needed. We do not make this unconditional as it
would result in growing the resulting binary on the many platforms which
have no users of the devm_.alloc family of functions.
Link: https://lore.kernel.org/r/20251227223833.3019311-1-trini@konsulko.com
The devm alloc functions that we have may follow the Linux kernel model
where allocations are (almost always) automatically free()'d. However,
quite often we don't enable, in full U-Boot, the tracking and free()'ing
functionality. This in turn leads to memory leaks because the driver
author expects that since the functions have the same name as in the
Linux Kernel they have the same behavior. In turn we then get
functionally correct commits such as commit 00e1fed93c8c ("firmware:
ti_sci: Fix memory leaks in devm_ti_sci_get_of_resource") that manually
add these calls. Rather than manually tracking allocations and
implementing free()s, rework things so that we follow expectations by
enabling the DEVRES functionality (outside of xPL phases).
This turns DEVRES from a prompted symbol to a symbol that must be
select'd, and we now remove our non-managed alloc/free functions from
outside of xPL builds.
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
If CONFIG_OF_PLATDATA=y , then the udevice has no valid OF node associated
with it and ofnode_valid(node) evaluates to 0. The dev_read_u32_default()
call ultimately reaches ofnode_read_u32_index() which invokes fdt_getprop()
and passes result of ofnode_to_offset(node) as an offset parameter into it.
The ofnode_to_offset(node) returns -1 for invalid node, which leads to an
fdt_getprop(..., -1, ...) invocation, which will crash sandbox with SIGSEGV
because libfdt can not handle negative node offsets without full tree check,
which U-Boot inhibits to keep size lower.
Since gpio_sandbox_probe() already calls dev_has_ofnode(dev) and assigns
uc_priv->gpio_count to CONFIG_SANDBOX_GPIO_COUNT accordingly, add matching
dev_has_ofnode(dev) check into sandbox_gpio_of_to_plat() and do not call
any of the dev_read_*() functions for devices without valid nodes there
either.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add SPL_DWAPB_GPIO configuration option to enable the Designware APB
GPIO driver in SPL builds.
Changes:
- Add SPL_DWAPB_GPIO Kconfig option with SPL_DM_GPIO dependency
- Update Makefile to use CONFIG_$(PHASE_)DWAPB_GPIO pattern for
conditional compilation in both SPL and main U-Boot builds
Signed-off-by: Tanmay Kathpalia <tanmay.kathpalia@altera.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
There is a condition guard which ensures that the GPIO node, indeed
describes a GPIO controller.
if (!fdtdec_get_bool(blob, node, "gpio-controller"))
continue;
Since the bank base is being incremented in the loop, it is done so
irrespective of whether the node is a GPIO controller or not. This leads
to the incorrect resolution of bank base addresses.
Move it out of the loop, and instead increment the bank base address
only if the driver successfully binds a GPIO controller.
Reviewed-by: Henrik Grimler <henrik@grimler.se>
Fixes: b8809e60cdb5 ("dm: exynos: gpio: Convert to driver model")
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rasmus Villemoes <ravi@prevas.dk> says:
Hopefully third time's the charm.
I merely wanted to add support (mostly for use by the 'gpio' shell
command) for looking up a gpio via the gpio-line-names DT property. We
already have a "gpio_request_by_line_name()", but cmd/gpio.c does a
separate "lookup + request", so it felt more natural to teach the
lookup machinery this as well. That ran into
OF_CONTROL-but-not-OF_LIBFDT being a thing for SPL, so here's yet
another attempt.
Now, when trying to do my civic duty and add tests for this, I found
that test/dm/gpio.c has been defunct for a couple of years, and
reinstating it is not entirely trivial.
After a couple of rounds CI is now happy with this:
https://github.com/u-boot/u-boot/pull/828
Link: https://lore.kernel.org/r/20251104174458.3385564-1-ravi@prevas.dk
In scripts as well as interactively, it's much nicer to be able to
refer to GPIOs via their names defined in the device tree property
"gpio-line-names", instead of the rather opaque names derived from the
bank name with a _xx suffix. E.g.
gpio read factory_reset FACTORY_RESET
if test $factory_reset = 1 ; then ...
versus
gpio read factory_reset gpio@481ac000_16
if test $factory_reset = 1 ; then ...
This is also consistent with the move on the linux/userspace side towards
using line names instead of legacy chip+offset or the even more legacy
global gpio numbering in sysfs.
As dev_read_stringlist_search() depends on both OF_CONTROL and
OF_LIBFDT (which matters for the SPL case), we need some .config
conditional. However, it only adds about ~50 bytes of code to U-Boot
proper, and dm_gpio_lookup_name() most often ends up being GC'ed for
SPL, thus adds no overhead there, so for now make it a hidden symbol
which is merely a convenient shorthand for
CONFIG_IS_ENABLED(OF_CONTROL) && CONFIG_IS_ENABLED(OF_LIBFDT).
Signed-off-by: Rasmus Villemoes <ravi@prevas.dk>
Reviewed-by: Heiko Schocher <hs@nabladev.com>
OMAP GPIO driver needs TI_SYSC to initialize its clocks when
using a devicetree-based setup.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Add support for the GPIO controller block in the R-Car Gen5 SoC family.
The GPIO controller has a General Input Enable Register (INEN), whose
reset state is to have all input disabled. The GPIO controller also has
updated offsets for its control registers. U-Boot uses three registers,
INDT, POSNEG, INEN, which have updated offsets, those are handled by the
driver.
Signed-off-by: Huy Bui <huy.bui.wm@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: - Access Gen5 specific registers via driver data offsets,
- Update commit message]
The Renesas R-Car Gen5 GPIO controller has INDT, POSNEG, INEN registers
at different offsets compared to previous generations. Introduce three
new entries in struct rcar_gpio_data {} match data to describe these
register offsets for each GPIO controller. Update the driver to access
these three registers through the match data offsets. No functional
change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Wrap the RCAR_GPIO_HAS_INEN quirk in more flexible struct rcar_gpio_data {}
in preparation for addition of Renesas R-Car Gen5 GPIO controller support.
The Renesas R-Car Gen5 GPIO controller requires more than a single quirk
to properly describe it, therefore increase the flexibility and introduce
full match data structure, and use it throughout the driver. No functional
change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Remove register macros for registers which are not used by this driver.
This makes it easier to get an overview of which registers are really
used by the driver. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The PFC offset is no longer used directly in the driver since commit
fbf26bea3964 ("gpio: renesas: Migrate to pinctrl GPIO accessors")
Drop the pfc_offset parsing.
Fixes: fbf26bea3964 ("gpio: renesas: Migrate to pinctrl GPIO accessors")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
If CONFIG_GPIO_HOG is not set, then gpio_hog_lookup_name() is empty,
and thus does not initialize any of its parameters. It does still
return 0 though, and so any calling function might assume that the
parameters have been initialized successfully.
Change the return value to -ENODEV in this case, as the function
would in the case when CONFIG_GPIO_HOG is set but the gpio hog
could not be found.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Heiko Schocher <hs@nabladev.com>
The GPIOs on PM7325 work fine using the qcom_spmi_gpio driver and
enables the use of the Volume Up button Fairphone 5 smartphone.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250917-spmi-gpio-pm7325-v1-1-6b75c2c62d8b@fairphone.com
Signed-off-by: Casey Connolly <kcxt@postmarketos.org>
The GPIOs on PM6350 work fine using the qcom_spmi_gpio driver and
enables the use of the Volume Up button Fairphone 4 smartphone.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
This is used for the volume keys on some SDM670 devices.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: David Wronek <david.wronek@mainlining.org>
Link: https://lore.kernel.org/r/20251003-sdm670-v2-5-52c0fa481286@mainlining.org
Signed-off-by: Casey Connolly <kcxt@postmarketos.org>
Add support for the GPIOs in the PM6150L to the new driver.
Signed-off-by: Jens Reidel <adrian@mainlining.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Casey Connolly <casey.connolly@linaro.org>
Link: https://lore.kernel.org/r/20251005154443.71477-1-adrian@mainlining.org
Signed-off-by: Casey Connolly <kcxt@postmarketos.org>
In intel_gpio_set_flags the two variables or0 and or1 may be used
uninitialised. Correct this by setting initial values in the
declaration.
Also there is no need to use '|=' when the initial value is 0 and there
is only one assignment performed to each variable so just use '='
instead.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
This driver has never been enabled and currently has build problems
related in part to incorrect out_le32 calls. Remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently xilinx_pm_request API supports four u32 payloads. However the
legacy SMC format supports five u32 request payloads and extended SMC
format supports six u32 request payloads. Add support for the same in
xilinx_pm_request API. Also add two dummy arguments to all the callers
of xilinx_pm_request.
The TF-A always fills seven u32 return payload so add support
for the same in xilinx_pm_request API.
Signed-off-by: Naman Trivedi <naman.trivedimanojbhai@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Acked-by: Senthil Nathan Thangaraj <senthilnathan.thangaraj@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/5ae6b560741f3ca8b89059c4ebb87acf75b4718e.1756388537.git.michal.simek@amd.com
All instances of the U_BOOT_DRIVER must use a unique name or they will
lead to link time failures due to name space conflicts when both are
present. In this case gpio-aspeed-g7 was using the same name as
gpio-aspeed.
Signed-off-by: Tom Rini <trini@konsulko.com>
mchp_gpio_get_value() should return int instead of bool, and some casts
are needed.
Signed-off-by: Eoin Dickson <eoin.dickson@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The ADP5587 is a simpler version of the ADP5588. The ADP5588 can
configure two pins, C8 and C9, as GPIOs or light sensors. The ADP5587
does not include the light sensors.
Signed-off-by: Philip Molloy <philip@philipmolloy.com>
In gpio_dwapb_bind plat is used to reference memory allocated by
devm_kcalloc but it is attempted to be freed using kfree. Instead free
this memory using the correct devm_kfree function.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Acked-by: Quentin Schulz <quentin.schulz@cherry.de>
The 'dev' parameter in the zynq_gpio_get_bank_pin function was not
described in its kernel-doc comment block, leading to a Sparse warning.
drivers/gpio/zynq_gpio.c:194: warning: Function parameter or member 'dev'
not described in 'zynq_gpio_get_bank_pin'
Add a description for the 'dev' parameter to satisfy the documentation
requirements and improve code clarity for this function.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20250717044632.1353588-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
This driver adds GPIO support for PolarFire SoC family, this is required
to add sd card support on the Beagle-V-Fire as it uses GPIO chip selects
Signed-off-by: Eoin Dickson <eoin.dickson@microchip.com>
Acked-by: Leo Yu-Chi Liang <ycliang@andestech.com>
DM_GPIO_LOOKUP_LABEL and SPL_DM_GPIO_LOOKUP_LABEL had the same
description and therefore appeared to be duplicates in Kconfig frontends
Signed-off-by: Philip Molloy <philip.molloy@analog.com>
Move support of the pm8550 gpios to the newly introduced
driver and drop the compatible entry and the read-only quirk
at the same time from the old driver.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org>
Acked-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250630-topic-sm8x50-pmic-gpio-pinctrl-new-v2-2-cc1512931197@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
The current qcom_pmic_gpio driver is too limited and doesn't
support state tracking for all pins like the Linux driver.
Adding full pinconf support would require adding the state
and it's much simpler to restart from scratch with a new
driver based on the Linux one adapted to the U-Boot GPIO
and Pinctrl APIs.
For now only the PMICs I've been able to validate are
added in the compatible list but we should be able to
add the entire list from the Linux driver.
There's a few difference from the Linux driver:
- no IRQ support
- uses the U-Boot GPIO flags that maps very well
- uses the gpio-ranges to get the pins count
- no debugfs but prints the pin state via pinmux callback
It uses the same CONFIG entry as the old one, since
the ultimate goal is to migrate entirely on this new
driver once we verify it doesn't break the older
platforms.
Tested-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org>
Acked-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250630-topic-sm8x50-pmic-gpio-pinctrl-new-v2-1-cc1512931197@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
A large number of gpio drivers cannot build without access to some platform
specific header files. Express those requirements in Kconfig as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
