Move DRAM bank detection from fdtdec to custom implementation to
ensure memory banks are populated before get_page_table_size() is
called during MMU initialization.
The current fdtdec-based approach populates gd->bd->bi_dram[] too
late in the boot sequence, causing get_page_table_size() to be
called with unpopulated DRAM information. This prevents dynamic
page table sizing based on actual memory configuration.
Parse /memory nodes in dram_init() to fill versal2_mem_map[]
early enough for MMU setup. Supports up to
CONFIG_NR_DRAM_BANKS (36) non-contiguous banks with high memory
regions (>4GB) and use __weak get_page_table_size implementation
to estimate page table size based on the populated DRAM banks.
Signed-off-by: Pranav Sanwal <pranav.sanwal@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20260129120021.1328653-3-pranav.sanwal@amd.com
The eMMC boot device controller on Versal2 requires device pointer
initialization before accessing its sequence number. The EMMC_MODE case
was using dev_seq(dev) on an uninitialized pointer, causing corrupted
boot_targets entries (mmc7f7fbfbf instead of mmc0/mmc1).
Add uclass_get_device_by_name() call to properly initialize the device
pointer before reading the sequence number. The dev sequence number is
determined at runtime based on DT aliases.
Fix boot_targets corruption in eMMC boot mode, allowing proper boot
device selection instead of falling back to JTAG mode.
Signed-off-by: Pranav Tilak <pranav.vinaytilak@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20260113060107.1136297-1-pranav.vinaytilak@amd.com
SOC can boot from different boot medias and also different offsets that's
why by default show multiboot value to be aware which image system is
booting out of. It is especially useful for systems with A/B update
enabled.
Also limit zynqmp_pm_get_pmc_multi_boot_reg() usage only for Versal and
Versal Gen 2.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/fd7564ce2f51d965c273e939e98de01beb92e6f5.1764232124.git.michal.simek@amd.com
If sysreset is enabled reset_cpu is defined in sysreset uclass
that's why it can't be in platform/board code.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20250707040607.758919-3-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Read an eeprom after relocation which also shows information from
eeprom wired via nvmem aliases.
When DTB reselection is enabled eeprom is read before relocation
too but information is not showed. The issue about two i2c reads
in this case will be address separately.
Signed-off-by: Padmarao Begari <padmarao.begari@amd.com>
Link: https://lore.kernel.org/r/20250409162639.588487-3-padmarao.begari@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Enable saving variables to MMC(FAT) and SPI based on primary
bootmode. If bootmode is JTAG, dont save env anywhere(NOWHERE).
Enable ENV_FAT_DEVICE_AND_PART="0:auto" for Versal Gen 2 platform.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20250411154612.107136-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for loading the secure & non-secure pdi images and PL
bitstream on the Versal Gen2 platform. The FPGA driver is enabled
to load the bitstream in PDI format on the AMD Versal Gen2 device.
PDI is the new programmable device image format for Versal Gen2,
and the bitstream for the Versal Gen2 platform is generated exclusively
in this format.
With the enhanced SMC format in TF-A ensuring transparent payload
forwarding for Versal Gen2, the u-boot driver must now handle the
word swapping of PDI address that was previously done in TF-A for
this API. The source code for the Versal2 loadpdi command and the
CONFIG_CMD_VERSAL2 configuration has been removed. It now utilizes
the fpga load <dev> <address> <length> command to load secure &
non-secure pdi images.
Signed-off-by: Prasad Kummari <prasad.kummari@amd.com>
Link: https://lore.kernel.org/r/20250327105200.1262615-3-prasad.kummari@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add the UFS boot mode support and update the boot_targets with
ufs mode. If the UFS device is not accessible from APU and
running this is detected as a warning, as the device is not
accessible.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20250225032806.1842581-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
After adding the U_BOOT_LONGHELP macro some new commands came in still
that were not making use if it. Switch these cases over and in a few
places add missing newlines as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
