Merge branch '2022-03-18-Kconfig-migrations' into next

- A large number of Kconfig migrations.  This also includes a few
  convert-by-enable of DM_ETH on some i.MX platforms.

.azure-pipelines.yml

@@ -71,7 +71,7 @@ stages:
              grep '#define[[:blank:]]CONFIG_' $CFG | \
                 sed -n 's/#define.\(CONFIG_[A-Za-z0-9_]*\).*/\1/p' | \
                 sort -u > ${KUSEDLST} || true
-             NUM=`comm -12 --total --output-delimiter=, ${KSYMLST} ${KUSEDLST} | \
+             NUM=`comm -123 --total --output-delimiter=, ${KSYMLST} ${KUSEDLST} | \
                 cut -d , -f 3`
              if [[ $NUM -ne 0 ]]; then
                 echo "Unmigrated symbols found in $CFG"

.gitlab-ci.yml

@@ -132,7 +132,7 @@ check for migrated symbols in board header:
          grep '#define[[:blank:]]CONFIG_' $CFG |
             sed -n 's/#define.\(CONFIG_[A-Za-z0-9_]*\).*/\1/p' |
             sort -u > ${KUSEDLST} || true;
-         NUM=`comm -12 --total --output-delimiter=, ${KSYMLST} ${KUSEDLST} |
+         NUM=`comm -123 --total --output-delimiter=, ${KSYMLST} ${KUSEDLST} |
             cut -d , -f 3`;
          if [[ $NUM -ne 0 ]]; then
             echo "Unmigrated symbols found in $CFG";

README

@@ -374,14 +374,6 @@ The following options need to be configured:
 		See Freescale App Note 4493 for more information about
 		this erratum.
 
-		CONFIG_A003399_NOR_WORKAROUND
-		Enables a workaround for IFC erratum A003399. It is only
-		required during NOR boot.
-
-		CONFIG_A008044_WORKAROUND
-		Enables a workaround for T1040/T1042 erratum A008044. It is only
-		required during NAND boot and valid for Rev 1.0 SoC revision
-
 		CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY
 
 		This is the value to write into CCSR offset 0x18600
@@ -565,13 +557,6 @@ The following options need to be configured:
 		boards with QUICC Engines require OF_QE to set UCC MAC
 		addresses
 
-		CONFIG_OF_SYSTEM_SETUP
-
-		Other code has addition modification that it wants to make
-		to the flat device tree before handing it off to the kernel.
-		This causes ft_system_setup() to be called before booting
-		the kernel.
-
 		CONFIG_OF_IDE_FIXUP
 
 		U-Boot can detect if an IDE device is present or not.
@@ -1563,24 +1548,6 @@ The following options need to be configured:
 			FLAGADM
 
 - Error Recovery:
-		CONFIG_NET_RETRY_COUNT
-
-		This variable defines the number of retries for
-		network operations like ARP, RARP, TFTP, or BOOTP
-		before giving up the operation. If not defined, a
-		default value of 5 is used.
-
-		CONFIG_ARP_TIMEOUT
-
-		Timeout waiting for an ARP reply in milliseconds.
-
-		CONFIG_NFS_TIMEOUT
-
-		Timeout in milliseconds used in NFS protocol.
-		If you encounter "ERROR: Cannot umount" in nfs command,
-		try longer timeout such as
-		#define CONFIG_NFS_TIMEOUT 10000UL
-
 	Note:
 
 		In the current implementation, the local variables
@@ -1847,10 +1814,6 @@ The following options need to be configured:
 		CONFIG_SPL_SKIP_RELOCATE
 		Avoid SPL relocation
 
-		CONFIG_SPL_NAND_IDENT
-		SPL uses the chip ID list to identify the NAND flash.
-		Requires CONFIG_SPL_NAND_BASE.
-
 		CONFIG_SPL_UBI
 		Support for a lightweight UBI (fastmap) scanner and
 		loader

arch/arm/cpu/armv7/Kconfig

@@ -27,6 +27,37 @@ config ARMV7_BOOT_SEC_DEFAULT
 	This can be overridden at run-time by setting the bootm_boot_mode env.
 	variable to "sec" or "nonsec".
 
+config HAS_ARMV7_SECURE_BASE
+	bool "Enable support for a ahardware secure memory area"
+	default y if ARCH_LS1021A || ARCH_MX7 || ARCH_MX7ULP || ARCH_STM32MP \
+			|| MACH_SUN6I || MACH_SUN7I || MACH_SUN8I || TEGRA124
+
+config ARMV7_SECURE_BASE
+	hex "Base address for secure mode memory"
+	depends on HAS_ARMV7_SECURE_BASE
+	default 0xfff00000 if TEGRA124
+	default 0x2ffc0000 if ARCH_STM32MP
+	default 0x2f000000 if ARCH_MX7ULP
+	default 0x10010000 if ARCH_LS1021A
+	default 0x00900000 if ARCH_MX7
+	default 0x00044000 if MACH_SUN8I
+	default 0x00020000 if MACH_SUN6I || MACH_SUN7I
+
+config ARMV7_SECURE_RESERVE_SIZE
+	hex
+	depends on TEGRA124 && HAS_ARMV7_SECURE_BASE
+	default 0x100000
+	help
+	  Reserve top 1M for secure RAM
+
+config ARMV7_SECURE_MAX_SIZE
+	hex
+	depends on ARMV7_SECURE_BASE && ARCH_STM32MP || MACH_SUN6I \
+			|| MACH_SUN7I || MACH_SUN8I
+	default 0xbc00 if MACH_SUN8I && !MACH_SUN8I_H3
+	default 0x3c00 if MACH_SUN8I && MACH_SUN8I_H3
+	default 0x10000
+
 config ARMV7_VIRT
 	bool "Enable support for hardware virtualization" if EXPERT
 	depends on CPU_V7_HAS_VIRT && ARMV7_NONSEC

arch/arm/cpu/armv8/Kconfig

@@ -31,6 +31,12 @@ config ARMV8_SET_SMPEN
 	  it can be safely enabled when EL2/EL3 initialized SMPEN bit
 	  or when CPU implementation doesn't include that register.
 
+config ARMV8_SWITCH_TO_EL1
+	bool "Enable switching to running in EL1"
+	help
+	  In some circumstances we need to switch to running in EL1.
+	  Enable this option to have U-Boot switch to EL1.
+
 config ARMV8_SPIN_TABLE
 	bool "Support spin-table enable method"
 	depends on ARMV8_MULTIENTRY && OF_LIBFDT

arch/arm/mach-at91/Kconfig

@@ -176,6 +176,7 @@ config TARGET_SAMA5D2_XPLAINED
 
 config TARGET_SAMA5D27_SOM1_EK
 	bool "SAMA5D27 SOM1 EK board"
+	select SAMA5D2
 	select BOARD_EARLY_INIT_F
 	select BOARD_LATE_INIT
 	select CPU_V7A
@@ -310,6 +311,13 @@ config AT91_EFLASH
 	  Enable the driver for the embedded flash used in the Atmel
 	  AT91SAM9XE devices.
 
+config AT91_GPIO_PULLUP
+	bool "Keep pullups on peripheral pins"
+	depends on CPU_ARM926EJS
+
+config ATMEL_LEGACY
+	bool "Legacy GPIO support"
+
 source "board/atmel/at91sam9260ek/Kconfig"
 source "board/atmel/at91sam9261ek/Kconfig"
 source "board/atmel/at91sam9263ek/Kconfig"

arch/arm/mach-mvebu/include/mach/config.h

@@ -35,14 +35,6 @@
 /* Needed for SPI NOR booting in SPL */
 #define CONFIG_DM_SEQ_ALIAS		1
 
-/*
- * Ethernet Driver configuration
- */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_ARP_TIMEOUT	200
-#define CONFIG_NET_RETRY_COUNT	50
-#endif /* CONFIG_CMD_NET */
-
 /*
  * I2C related stuff
  */

arch/arm/mach-omap2/am33xx/Kconfig

@@ -280,3 +280,35 @@ config PUB_ROM_DATA_SIZE
 	  image, this area is no longer used, and can be reclaimed
 	  for run time use by the boot image.
 endif
+
+config AM335X_USB0
+	bool "Static mode configuration for USB0 in SPL"
+	depends on AM33XX && SPL_MUSB_NEW && !SPL_OF_CONTROL
+
+choice
+	prompt "USB0 port configuration"
+	depends on AM335X_USB0
+
+config AM335X_USB0_HOST
+	bool "Port is used in host mode"
+
+config AM335X_USB0_PERIPHERAL
+	bool "Port is used in peripheral mode"
+
+endchoice
+
+config AM335X_USB1
+	bool "Static mode configuration for USB1 in SPL"
+	depends on AM33XX && SPL_MUSB_NEW && !SPL_OF_CONTROL
+
+choice
+	prompt "USB1 port configuration"
+	depends on AM335X_USB1
+
+config AM335X_USB1_HOST
+	bool "Port is used in host mode"
+
+config AM335X_USB1_PERIPHERAL
+	bool "Port is used in peripheral mode"
+
+endchoice

arch/arm/mach-omap2/am33xx/board.c

@@ -241,14 +241,14 @@ static struct ti_musb_plat usb1 = {
 };
 
 U_BOOT_DRVINFOS(am33xx_usbs) = {
-#if CONFIG_AM335X_USB0_MODE == MUSB_PERIPHERAL
+#ifdef CONFIG_AM335X_USB0_PERIPHERAL
 	{ "ti-musb-peripheral", &usb0 },
-#elif CONFIG_AM335X_USB0_MODE == MUSB_HOST
+#elif defined(CONFIG_AM335X_USB0_HOST)
 	{ "ti-musb-host", &usb0 },
 #endif
-#if CONFIG_AM335X_USB1_MODE == MUSB_PERIPHERAL
+#ifdef CONFIG_AM335X_USB1_PERIPHERAL
 	{ "ti-musb-peripheral", &usb1 },
-#elif CONFIG_AM335X_USB1_MODE == MUSB_HOST
+#elif defined(CONFIG_AM335X_USB1_HOST)
 	{ "ti-musb-host", &usb1 },
 #endif
 };

arch/powerpc/cpu/mpc83xx/fdt.c

@@ -51,9 +51,6 @@ void ft_cpu_setup(void *blob, struct bd_info *bd)
 		 REVID_MAJOR(spridr) >= 2)
 		fdt_fixup_crypto_node(blob, 0x0204);
 
-#if defined(CONFIG_HAS_ETH0) || defined(CONFIG_HAS_ETH1) ||\
-    defined(CONFIG_HAS_ETH2) || defined(CONFIG_HAS_ETH3) ||\
-    defined(CONFIG_HAS_ETH4) || defined(CONFIG_HAS_ETH5)
 #ifdef CONFIG_ARCH_MPC8313
 	/*
 	* mpc8313e erratum IPIC1 swapped TSEC interrupt ID numbers on rev. 1
@@ -66,7 +63,6 @@ void ft_cpu_setup(void *blob, struct bd_info *bd)
 
 		nodeoffset = fdt_path_offset(blob, "/aliases");
 		if (nodeoffset >= 0) {
-#if defined(CONFIG_HAS_ETH0)
 			prop = fdt_getprop(blob, nodeoffset, "ethernet0", NULL);
 			if (prop) {
 				u32 tmp[] = { 32, 0x8, 33, 0x8, 34, 0x8 };
@@ -78,8 +74,6 @@ void ft_cpu_setup(void *blob, struct bd_info *bd)
 					fdt_setprop(blob, path, "interrupts",
 						    &tmp, sizeof(tmp));
 			}
-#endif
-#if defined(CONFIG_HAS_ETH1)
 			prop = fdt_getprop(blob, nodeoffset, "ethernet1", NULL);
 			if (prop) {
 				u32 tmp[] = { 35, 0x8, 36, 0x8, 37, 0x8 };
@@ -91,10 +85,8 @@ void ft_cpu_setup(void *blob, struct bd_info *bd)
 					fdt_setprop(blob, path, "interrupts",
 						    &tmp, sizeof(tmp));
 			}
-#endif
 		}
 	}
-#endif
 #endif
 
 	do_fixup_by_prop_u32(blob, "device_type", "cpu", 4,

arch/powerpc/cpu/mpc85xx/Kconfig

@@ -354,6 +354,7 @@ config ARCH_MPC8560
 
 config ARCH_P1010
 	bool
+	select A003399_NOR_WORKAROUND if SYS_FSL_ERRATUM_IFC_A003399 && !SPL
 	select BTB
 	select FSL_LAW
 	select SYS_CACHE_SHIFT_5
@@ -878,6 +879,18 @@ config SYS_CCSRBAR_DEFAULT
 		if changed by pre-boot regime. The value here must match
 		the current value in SoC. If not sure, do not change.
 
+config A003399_NOR_WORKAROUND
+	bool
+	help
+	  Enables a workaround for IFC erratum A003399. It is only required
+	  during NOR boot.
+
+config A008044_WORKAROUND
+	bool
+	help
+	  Enables a workaround for T1040/T1042 erratum A008044. It is only
+	  required during NAND boot and valid for Rev 1.0 SoC revision
+
 config SYS_FSL_ERRATUM_A004468
 	bool
 
@@ -960,6 +973,7 @@ config SYS_FSL_ERRATUM_A007907
 
 config SYS_FSL_ERRATUM_A008044
 	bool
+	select A008044_WORKAROUND if MTD_RAW_NAND
 
 config SYS_FSL_ERRATUM_CPC_A002
 	bool

arch/powerpc/cpu/mpc85xx/mp.c

@@ -456,18 +456,18 @@ void setup_mp(void)
 	flush_cache(bootpg, 4096);
 
 	/* look for the tlb covering the reset page, there better be one */
-	i = find_tlb_idx((void *)CONFIG_BPTR_VIRT_ADDR, 1);
+	i = find_tlb_idx((void *)BPTR_VIRT_ADDR, 1);
 
 	/* we found a match */
 	if (i != -1) {
 		/* map reset page to bootpg so we can copy code there */
 		disable_tlb(i);
 
-		set_tlb(1, CONFIG_BPTR_VIRT_ADDR, bootpg, /* tlb, epn, rpn */
+		set_tlb(1, BPTR_VIRT_ADDR, bootpg, /* tlb, epn, rpn */
 			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, /* perms, wimge */
 			0, i, BOOKE_PAGESZ_4K, 1); /* ts, esel, tsize, iprot */
 
-		memcpy((void *)CONFIG_BPTR_VIRT_ADDR, (void *)fixup, 4096);
+		memcpy((void *)BPTR_VIRT_ADDR, (void *)fixup, 4096);
 
 		plat_mp_up(bootpg_map, pagesize);
 	} else {

arch/powerpc/include/asm/config.h

@@ -31,9 +31,7 @@
  * Freescale's default e500 reset page.
  */
 #if (defined(CONFIG_E500) && defined(CONFIG_MP))
-#ifndef CONFIG_BPTR_VIRT_ADDR
+#define BPTR_VIRT_ADDR	0xfffff000
-#define CONFIG_BPTR_VIRT_ADDR	0xfffff000
-#endif
 #endif
 
 /* Since so many PPC SOCs have a semi-common LBC, define this here */

board/atmel/at91sam9260ek/Kconfig

@@ -9,4 +9,19 @@ config SYS_VENDOR
 config SYS_CONFIG_NAME
 	default "at91sam9260ek"
 
+choice
+	prompt "Evaluation board"
+
+config AT91SAM9G20EK
+	bool "Atmel AT91SAM9G20 EK"
+
+config AT91SAM9260EK
+	bool "Atmel AT91SAM9260 EK"
+
+endchoice
+
+config AT91SAM9G20EK_2MMC
+	bool "Atmel AT91SAM9G20 EK 2MMC variant"
+	depends on AT91SAM9260EK
+
 endif

board/atmel/at91sam9261ek/Kconfig

@@ -9,4 +9,18 @@ config SYS_VENDOR
 config SYS_CONFIG_NAME
 	default "at91sam9261ek"
 
+choice
+	prompt "Evaluation board"
+
+config AT91SAM9G10EK
+	bool "Atmel AT91SAM9G10 EK"
+
+config AT91SAM9261EK
+	bool "Atmel AT91SAM9261 EK"
+
+config AT91SAM9G10
+	bool "Atmel AT91SAM9G10 EK"
+
+endchoice
+
 endif

board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c

@@ -214,7 +214,8 @@ static void at91sam9m10g45ek_lcd_hw_init(void)
 
 	at91_periph_clk_enable(ATMEL_ID_LCDC);
 
-	gd->fb_base = CONFIG_AT91SAM9G45_LCD_BASE;
+	/* board specific(not enough SRAM) */
+	gd->fb_base = 0x73E00000;
 }
 
 #ifdef CONFIG_LCD_INFO
@@ -267,11 +268,7 @@ int board_early_init_f(void)
 int board_init(void)
 {
 	/* arch number of AT91SAM9M10G45EK-Board */
-#ifdef CONFIG_AT91SAM9M10G45EK
 	gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9M10G45EK;
-#elif defined CONFIG_AT91SAM9G45EKES
-	gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G45EKES;
-#endif
 
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;

board/boundary/nitrogen6x/nitrogen6x.c

@@ -356,10 +356,6 @@ int board_eth_init(struct bd_info *bis)
 		goto free_phydev;
 #endif
 
-#ifdef CONFIG_CI_UDC
-	/* For otg ethernet*/
-	usb_eth_initialize(bis);
-#endif
 	return 0;
 
 free_phydev:

boot/Kconfig

@@ -991,6 +991,36 @@ config AUTOBOOT_MENU_SHOW
 	  environmnent variable (if enabled) and before handling the boot delay.
 	  See README.bootmenu for more details.
 
+config BOOT_RETRY
+	bool "Boot retry feature"
+	help
+	  Allow for having the U-Boot command prompt time out and attempt
+	  to boot again.  If the environment variable "bootretry" is found then
+	  its value is used, otherwise the retry timeout is
+	  CONFIG_BOOT_RETRY_TIME.  CONFIG_BOOT_RETRY_MIN is optional and
+	  defaults to CONFIG_BOOT_RETRY_TIME. All times are in seconds.
+
+config BOOT_RETRY_TIME
+	int "Timeout in seconds before attempting to boot again"
+	depends on BOOT_RETRY
+	help
+	  Time in seconds before the U-Boot prompt will timeout and boot will
+	  be attempted again.
+
+config BOOT_RETRY_MIN
+	int "Minimum timeout in seconds for 'bootretry'"
+	depends on BOOT_RETRY
+	default BOOT_RETRY_TIME
+	help
+	  The minimum time in seconds that "bootretry" can be set to.
+
+config RESET_TO_RETRY
+	bool "Reset the board to retry autoboot"
+	depends on BOOT_RETRY
+	help
+	  After the countdown timed out, the board will be reset to restart
+	  again.
+
 endmenu
 
 config USE_BOOTARGS

boot/Makefile

@@ -5,11 +5,7 @@
 
 ifndef CONFIG_SPL_BUILD
 
-# This option is not just y/n - it can have a numeric value
+obj-$(CONFIG_BOOT_RETRY) += bootretry.o
-ifdef CONFIG_BOOT_RETRY_TIME
-obj-y += bootretry.o
-endif
-
 obj-$(CONFIG_CMD_BOOTM) += bootm.o bootm_os.o
 obj-$(CONFIG_CMD_BOOTZ) += bootm.o bootm_os.o
 obj-$(CONFIG_CMD_BOOTI) += bootm.o bootm_os.o

boot/bootretry.c

@@ -12,10 +12,6 @@
 #include <time.h>
 #include <watchdog.h>
 
-#ifndef CONFIG_BOOT_RETRY_MIN
-#define CONFIG_BOOT_RETRY_MIN CONFIG_BOOT_RETRY_TIME
-#endif
-
 static uint64_t endtime;  /* must be set, default is instant timeout */
 static int      retry_time = -1; /* -1 so can call readline before main_loop */
 

cmd/Kconfig

@@ -1638,6 +1638,15 @@ config CMD_NFS
 	help
 	  Boot image via network using NFS protocol.
 
+config NFS_TIMEOUT
+	int "Timeout in milliseconds for NFS mounts"
+	depends on CMD_NFS
+	default 2000
+	help
+	  Timeout in milliseconds used in NFS protocol.  If you encounter
+	  "ERROR: Cannot umount" in nfs command, try longer timeout such as
+	  10000.
+
 config CMD_MII
 	bool "mii"
 	imply CMD_MDIO

configs/Bananapi_M2_Ultra_defconfig

@@ -9,6 +9,7 @@ CONFIG_MMC0_CD_PIN="PH13"
 CONFIG_MMC_SUNXI_SLOT_EXTRA=2
 CONFIG_USB1_VBUS_PIN="PH23"
 CONFIG_USB2_VBUS_PIN="PH23"
+# CONFIG_HAS_ARMV7_SECURE_BASE is not set
 CONFIG_AHCI=y
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
 CONFIG_SPL_I2C=y

configs/LicheePi_Zero_defconfig

@@ -4,4 +4,5 @@ CONFIG_DEFAULT_DEVICE_TREE="sun8i-v3s-licheepi-zero"
 CONFIG_SPL=y
 CONFIG_MACH_SUN8I_V3S=y
 CONFIG_DRAM_CLK=360
+# CONFIG_HAS_ARMV7_SECURE_BASE is not set
 # CONFIG_NETDEVICES is not set

configs/MPC837XERDB_defconfig

@@ -171,6 +171,8 @@ CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_ADDR=0xFE080000
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="TSEC0"
 CONFIG_DM=y
 CONFIG_FSL_SATA=y
 CONFIG_SYS_SATA_MAX_DEVICE=2

configs/MPC8548CDS_36BIT_defconfig

@@ -32,6 +32,8 @@ CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_ADDR=0xFFF60000
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="8548cds/uImage.uboot"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC0"
 CONFIG_DM=y
 CONFIG_CHIP_SELECTS_PER_CTRL=2
 CONFIG_DDR_ECC=y

configs/MPC8548CDS_defconfig

@@ -31,6 +31,8 @@ CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_ADDR=0xFFF60000
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="8548cds/uImage.uboot"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC0"
 CONFIG_DM=y
 CONFIG_CHIP_SELECTS_PER_CTRL=2
 CONFIG_DDR_ECC=y

configs/MPC8548CDS_legacy_defconfig

@@ -31,6 +31,8 @@ CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_ADDR=0xFFF60000
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="8548cds/uImage.uboot"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC0"
 CONFIG_DM=y
 CONFIG_CHIP_SELECTS_PER_CTRL=2
 CONFIG_DDR_ECC=y

configs/P1010RDB-PA_36BIT_NAND_defconfig

@@ -55,6 +55,8 @@ CONFIG_ENV_IS_IN_NAND=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/P1010RDB-PA_36BIT_NOR_defconfig

@@ -37,6 +37,8 @@ CONFIG_ENV_IS_IN_FLASH=y
 CONFIG_ENV_ADDR=0xEFF20000
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/P1010RDB-PA_36BIT_SDCARD_defconfig

@@ -49,6 +49,8 @@ CONFIG_ENV_IS_IN_MMC=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/P1010RDB-PA_36BIT_SPIFLASH_defconfig

@@ -51,6 +51,8 @@ CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/P1010RDB-PA_NAND_defconfig

@@ -54,6 +54,8 @@ CONFIG_ENV_IS_IN_NAND=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/P1010RDB-PA_NOR_defconfig

@@ -36,6 +36,8 @@ CONFIG_ENV_IS_IN_FLASH=y
 CONFIG_ENV_ADDR=0xEFF20000
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/P1010RDB-PA_SDCARD_defconfig

@@ -48,6 +48,8 @@ CONFIG_ENV_IS_IN_MMC=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/P1010RDB-PA_SPIFLASH_defconfig

@@ -50,6 +50,8 @@ CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/P1010RDB-PB_36BIT_NAND_defconfig

@@ -56,6 +56,8 @@ CONFIG_ENV_IS_IN_NAND=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/P1010RDB-PB_36BIT_NOR_defconfig

@@ -38,6 +38,8 @@ CONFIG_ENV_IS_IN_FLASH=y
 CONFIG_ENV_ADDR=0xEFF20000
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/P1010RDB-PB_36BIT_SDCARD_defconfig

@@ -50,6 +50,8 @@ CONFIG_ENV_IS_IN_MMC=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/P1010RDB-PB_36BIT_SPIFLASH_defconfig

@@ -52,6 +52,8 @@ CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/P1010RDB-PB_NAND_defconfig

@@ -55,6 +55,8 @@ CONFIG_ENV_IS_IN_NAND=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/P1010RDB-PB_NOR_defconfig

@@ -37,6 +37,8 @@ CONFIG_ENV_IS_IN_FLASH=y
 CONFIG_ENV_ADDR=0xEFF20000
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/P1010RDB-PB_SDCARD_defconfig

@@ -49,6 +49,8 @@ CONFIG_ENV_IS_IN_MMC=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/P1010RDB-PB_SPIFLASH_defconfig

@@ -51,6 +51,8 @@ CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/P1020RDB-PC_36BIT_NAND_defconfig

@@ -55,6 +55,8 @@ CONFIG_ENV_IS_IN_NAND=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_DDR_CLK_FREQ=66666666
 CONFIG_CHIP_SELECTS_PER_CTRL=1

configs/P1020RDB-PC_36BIT_SDCARD_defconfig

@@ -50,6 +50,8 @@ CONFIG_ENV_IS_IN_MMC=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_DDR_CLK_FREQ=66666666
 CONFIG_CHIP_SELECTS_PER_CTRL=1

configs/P1020RDB-PC_36BIT_SPIFLASH_defconfig

@@ -52,6 +52,8 @@ CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_DDR_CLK_FREQ=66666666
 CONFIG_CHIP_SELECTS_PER_CTRL=1

configs/P1020RDB-PC_36BIT_defconfig

@@ -39,6 +39,8 @@ CONFIG_ENV_IS_IN_FLASH=y
 CONFIG_ENV_ADDR=0xEFF20000
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_DDR_CLK_FREQ=66666666
 CONFIG_CHIP_SELECTS_PER_CTRL=1

configs/P1020RDB-PC_NAND_defconfig

@@ -54,6 +54,8 @@ CONFIG_ENV_IS_IN_NAND=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_DDR_CLK_FREQ=66666666
 CONFIG_CHIP_SELECTS_PER_CTRL=1

configs/P1020RDB-PC_SDCARD_defconfig

@@ -49,6 +49,8 @@ CONFIG_ENV_IS_IN_MMC=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_DDR_CLK_FREQ=66666666
 CONFIG_CHIP_SELECTS_PER_CTRL=1

configs/P1020RDB-PC_SPIFLASH_defconfig

@@ -51,6 +51,8 @@ CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_DDR_CLK_FREQ=66666666
 CONFIG_CHIP_SELECTS_PER_CTRL=1

configs/P1020RDB-PC_defconfig

@@ -38,6 +38,8 @@ CONFIG_ENV_IS_IN_FLASH=y
 CONFIG_ENV_ADDR=0xEFF20000
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_DDR_CLK_FREQ=66666666
 CONFIG_CHIP_SELECTS_PER_CTRL=1

configs/P1020RDB-PD_NAND_defconfig

@@ -57,6 +57,8 @@ CONFIG_ENV_IS_IN_NAND=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_DDR_CLK_FREQ=66666666
 CONFIG_CHIP_SELECTS_PER_CTRL=2

configs/P1020RDB-PD_SDCARD_defconfig

@@ -52,6 +52,8 @@ CONFIG_ENV_IS_IN_MMC=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_DDR_CLK_FREQ=66666666
 CONFIG_CHIP_SELECTS_PER_CTRL=2

configs/P1020RDB-PD_SPIFLASH_defconfig

@@ -54,6 +54,8 @@ CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_DDR_CLK_FREQ=66666666
 CONFIG_CHIP_SELECTS_PER_CTRL=2

configs/P1020RDB-PD_defconfig

@@ -41,6 +41,8 @@ CONFIG_ENV_IS_IN_FLASH=y
 CONFIG_ENV_ADDR=0xEFF20000
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_DDR_CLK_FREQ=66666666
 CONFIG_CHIP_SELECTS_PER_CTRL=2

configs/P2020RDB-PC_36BIT_NAND_defconfig

@@ -59,6 +59,8 @@ CONFIG_ENV_IS_IN_NAND=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_DDR_CLK_FREQ=66666666
 CONFIG_CHIP_SELECTS_PER_CTRL=1

configs/P2020RDB-PC_36BIT_SDCARD_defconfig

@@ -54,6 +54,8 @@ CONFIG_ENV_IS_IN_MMC=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_DDR_CLK_FREQ=66666666
 CONFIG_CHIP_SELECTS_PER_CTRL=1

configs/P2020RDB-PC_36BIT_SPIFLASH_defconfig

@@ -56,6 +56,8 @@ CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_DDR_CLK_FREQ=66666666
 CONFIG_CHIP_SELECTS_PER_CTRL=1

configs/P2020RDB-PC_36BIT_defconfig

@@ -43,6 +43,8 @@ CONFIG_ENV_IS_IN_FLASH=y
 CONFIG_ENV_ADDR=0xEFF20000
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_DDR_CLK_FREQ=66666666
 CONFIG_CHIP_SELECTS_PER_CTRL=1

configs/P2020RDB-PC_NAND_defconfig

@@ -58,6 +58,8 @@ CONFIG_ENV_IS_IN_NAND=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_DDR_CLK_FREQ=66666666
 CONFIG_CHIP_SELECTS_PER_CTRL=1

configs/P2020RDB-PC_SDCARD_defconfig

@@ -53,6 +53,8 @@ CONFIG_ENV_IS_IN_MMC=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_DDR_CLK_FREQ=66666666
 CONFIG_CHIP_SELECTS_PER_CTRL=1

configs/P2020RDB-PC_SPIFLASH_defconfig

@@ -55,6 +55,8 @@ CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_DDR_CLK_FREQ=66666666
 CONFIG_CHIP_SELECTS_PER_CTRL=1

configs/P2020RDB-PC_defconfig

@@ -42,6 +42,8 @@ CONFIG_ENV_IS_IN_FLASH=y
 CONFIG_ENV_ADDR=0xEFF20000
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
 CONFIG_DM=y
 CONFIG_DDR_CLK_FREQ=66666666
 CONFIG_CHIP_SELECTS_PER_CTRL=1

configs/P2041RDB_NAND_defconfig

@@ -41,6 +41,8 @@ CONFIG_ENV_IS_IN_NAND=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/P2041RDB_SDCARD_defconfig

@@ -42,6 +42,8 @@ CONFIG_ENV_IS_IN_MMC=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/P2041RDB_SPIFLASH_defconfig

@@ -43,6 +43,8 @@ CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/P2041RDB_defconfig

@@ -38,6 +38,8 @@ CONFIG_ENV_IS_IN_FLASH=y
 CONFIG_ENV_ADDR=0xEFF20000
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/P3041DS_NAND_defconfig

@@ -39,6 +39,8 @@ CONFIG_ENV_IS_IN_NAND=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/P3041DS_SDCARD_defconfig

@@ -40,6 +40,8 @@ CONFIG_ENV_IS_IN_MMC=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/P3041DS_SPIFLASH_defconfig

@@ -41,6 +41,8 @@ CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/P3041DS_defconfig

@@ -36,6 +36,8 @@ CONFIG_ENV_IS_IN_FLASH=y
 CONFIG_ENV_ADDR=0xEFF20000
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/P4080DS_SDCARD_defconfig

@@ -40,6 +40,8 @@ CONFIG_ENV_IS_IN_MMC=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
 CONFIG_DM=y
 CONFIG_FSL_CAAM=y
 CONFIG_DDR_ECC=y

configs/P4080DS_SPIFLASH_defconfig

@@ -41,6 +41,8 @@ CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
 CONFIG_DM=y
 CONFIG_FSL_CAAM=y
 CONFIG_DDR_ECC=y

configs/P4080DS_defconfig

@@ -36,6 +36,8 @@ CONFIG_ENV_IS_IN_FLASH=y
 CONFIG_ENV_ADDR=0xEFF20000
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
 CONFIG_DM=y
 CONFIG_FSL_CAAM=y
 CONFIG_DDR_ECC=y

configs/P5040DS_NAND_defconfig

@@ -40,6 +40,8 @@ CONFIG_ENV_IS_IN_NAND=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/P5040DS_SDCARD_defconfig

@@ -40,6 +40,8 @@ CONFIG_ENV_IS_IN_MMC=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/P5040DS_SPIFLASH_defconfig

@@ -41,6 +41,8 @@ CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/P5040DS_defconfig

@@ -36,6 +36,8 @@ CONFIG_ENV_IS_IN_FLASH=y
 CONFIG_ENV_ADDR=0xEFF20000
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/T1024RDB_NAND_defconfig

@@ -63,6 +63,8 @@ CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC4"
 CONFIG_DM=y
 CONFIG_FSL_CAAM=y
 CONFIG_SYS_FSL_DDR3=y

configs/T1024RDB_SDCARD_defconfig

@@ -62,6 +62,8 @@ CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_MMC=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC4"
 CONFIG_DM=y
 CONFIG_FSL_CAAM=y
 CONFIG_SYS_FSL_DDR3=y

configs/T1024RDB_SPIFLASH_defconfig

@@ -64,6 +64,8 @@ CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC4"
 CONFIG_DM=y
 CONFIG_FSL_CAAM=y
 CONFIG_SYS_FSL_DDR3=y

configs/T1024RDB_defconfig

@@ -47,6 +47,8 @@ CONFIG_ENV_IS_IN_FLASH=y
 CONFIG_ENV_ADDR=0xEFF20000
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC4"
 CONFIG_DM=y
 CONFIG_FSL_CAAM=y
 CONFIG_SYS_FSL_DDR3=y

configs/T1042D4RDB_NAND_defconfig

@@ -54,6 +54,8 @@ CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC4"
 CONFIG_DM=y
 CONFIG_FSL_CAAM=y
 CONFIG_DDR_CLK_FREQ=66666666

configs/T1042D4RDB_SDCARD_defconfig

@@ -53,6 +53,8 @@ CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_MMC=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC4"
 CONFIG_DM=y
 CONFIG_FSL_CAAM=y
 CONFIG_DDR_CLK_FREQ=66666666

configs/T1042D4RDB_SPIFLASH_defconfig

@@ -55,6 +55,8 @@ CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC4"
 CONFIG_DM=y
 CONFIG_FSL_CAAM=y
 CONFIG_DDR_CLK_FREQ=66666666

configs/T1042D4RDB_defconfig

@@ -38,6 +38,8 @@ CONFIG_ENV_IS_IN_FLASH=y
 CONFIG_ENV_ADDR=0xEFF20000
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC4"
 CONFIG_DM=y
 CONFIG_FSL_CAAM=y
 CONFIG_DDR_CLK_FREQ=66666666

configs/T2080QDS_NAND_defconfig

@@ -57,6 +57,8 @@ CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/T2080QDS_SDCARD_defconfig

@@ -56,6 +56,8 @@ CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_MMC=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/T2080QDS_SECURE_BOOT_defconfig

@@ -41,6 +41,8 @@ CONFIG_ENV_OVERWRITE=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_DYNAMIC_DDR_CLK_FREQ=y

configs/T2080QDS_SPIFLASH_defconfig

@@ -58,6 +58,8 @@ CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/T2080QDS_SRIO_PCIE_BOOT_defconfig

@@ -38,6 +38,8 @@ CONFIG_ENV_IS_IN_REMOTE=y
 CONFIG_ENV_ADDR=0xFFE20000
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/T2080QDS_defconfig

@@ -41,6 +41,8 @@ CONFIG_ENV_IS_IN_FLASH=y
 CONFIG_ENV_ADDR=0xEFF20000
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/T2080RDB_NAND_defconfig

@@ -61,6 +61,8 @@ CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/T2080RDB_SDCARD_defconfig

@@ -60,6 +60,8 @@ CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_MMC=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/T2080RDB_SPIFLASH_defconfig

@@ -62,6 +62,8 @@ CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/T2080RDB_defconfig

@@ -45,6 +45,8 @@ CONFIG_ENV_IS_IN_FLASH=y
 CONFIG_ENV_ADDR=0xEFF20000
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/T2080RDB_revD_NAND_defconfig

@@ -62,6 +62,8 @@ CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/T2080RDB_revD_SDCARD_defconfig

@@ -61,6 +61,8 @@ CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_MMC=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/T2080RDB_revD_SPIFLASH_defconfig

@@ -63,6 +63,8 @@ CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y

configs/T2080RDB_revD_defconfig

@@ -46,6 +46,8 @@ CONFIG_ENV_IS_IN_FLASH=y
 CONFIG_ENV_ADDR=0xEFF20000
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
 CONFIG_DM=y
 CONFIG_SYS_SATA_MAX_DEVICE=2
 CONFIG_FSL_CAAM=y