This patch adds support for the MikroTik RouterBOARD 960PGS (hEX
PoE/PowerBox Pro) router. The device has a USB 2.0 port and an SFP port for
adding optical fiber connectivity. The ports 2-5 can power other PoE
capable devices with the same voltage as applied to the unit.
Specifications:
- SoC: Qualcomm Atheros QCA9557
- Flash: 16 MB (SPI)
- RAM: 128 MB
- 1x Ethernet SFP: 1000
- 1x Ethernet RJ45: 10/100/1000 port with passive POE in
- 4x Ethernet RJ45: 10/100/1000 ports with 802.3af/at PoE out
- 1x USB 2.0 host port
- 1x reset button
See [1] and [2] for more details.
Flashing:
TFTP boot initramfs image and then perform sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Link: https://mikrotik.com/product/RB960PGS [1]
Link: https://mikrotik.com/product/RB960PGS-PB [2]
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Signed-off-by: Chester A. Unal <chester.a.unal@arinc9.com>
Unset the SWCONFIG symbol and AR8216_PHY which selects SWCONFIG. Add
kmod-switch-ar8xxx, which enables AR8216_PHY, to DEFAULT_PACKAGES for the
subtarget. With this, swconfig driver will be now compiled as a module, as
kmod-switch-ar8xxx selects kmod-swconfig.
Refresh the config-default file for ath79/mikrotik while at it.
This change makes it possible to disable the swconfig driver for MikroTik
RouterBOARD 960PGS (hEX PoE/PowerBox Pro).
Signed-off-by: Chester A. Unal <chester.a.unal@arinc9.com>
Import pending series introducing support for standalone PCS drivers.
This has previously already been used by the airoha target, and is
also the base for the closer-to-upstream patches for MediaTek MT7988
10G SerDes support.
In order to not having to diverge from upstream also backport series
for standardized handling for PHY and PCS SerDes pair polarity.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is apparently a redundant u-boot config split between cfg1 and
cfg2. The size is also 0x10000 instead of the full amount.
This is needed in order to fix ethernet probing.
Fixes: 3faa3a04bb ("ath79: enterasys,ws-ap3805i: use nvmem")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22882
Signed-off-by: Robert Marko <robimarko@gmail.com>
The 6.18 testing kernel for ath79 target is ready now.
Tested on ath79/nand:Netgear R6100
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22771
Signed-off-by: Nick Hainke <vincent@systemli.org>
CONFIG_PAGE_BLOCK_MAX_ORDER was set to 10 as the page size is 4k.
All other kernel symbols are automatically refreshed by
`make kernel_oldconfig CONFIG_TARGET=target` and
`make kernel_oldconfig CONFIG_TARGET=subtarget`.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22771
Signed-off-by: Nick Hainke <vincent@systemli.org>
Copy patches and kernel configs from 6.18 kernel to restore the
default 6.12 kernel support files.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22771
Signed-off-by: Nick Hainke <vincent@systemli.org>
This is a preparation for 6.18 kernel support. It can help us
track the files history by using the Git tool.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22771
Signed-off-by: Nick Hainke <vincent@systemli.org>
The bootloader on this device is old and supports no lzma. So use
lzma-loader to work around this and get the size smaller so that an
image can actuallly be created and flashed. Because of these size
problems, the last usable version of OpenWrt was 23.05.
This UIMAGE_MAGIC seems to be used by other Netgear devices. Add to
avoid
jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00000000: 0x2705 instead
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22769
Signed-off-by: Robert Marko <robimarko@gmail.com>
Stocks args have
console=ttyS0,9600
rootfstype=squashfs
root=31:03
init=/sbin/init
mtdparts=ar7100-nor0:256k(u-boot),64k(u-boot-env),
1024k(vmlinux.gz.uImage),6208k(rootfs),512k(var),
64k(manufacturing-data),64k(ART)
rootfstype=squashfs,jffs2
which is wrong and interferes with OpenWrt. Keep the non default console
parameter to have console working properly.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22769
Signed-off-by: Robert Marko <robimarko@gmail.com>
For running, have it be the green LED as in stock firmware.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22769
Signed-off-by: Robert Marko <robimarko@gmail.com>
Using awk and cut to simulate -n is pointless.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22806
Signed-off-by: Robert Marko <robimarko@gmail.com>
This symbol is selected by CONFIG_BPF, which was already enabled
on generic config-6.12.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22730
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
<>, <> is the preferred way to specify multiple entries.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22736
Signed-off-by: Robert Marko <robimarko@gmail.com>
It seems the bootloader does not use 115200, which the dtsi file
specifies. Remove it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22735
Signed-off-by: Robert Marko <robimarko@gmail.com>
Needed so that the WiFi interfaces come up properly.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22735
Signed-off-by: Robert Marko <robimarko@gmail.com>
Users report pll-data is needed for gigabit speeds.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22735
Signed-off-by: Robert Marko <robimarko@gmail.com>
For whatever reason, in the transition from ar71xx to ath79, the second
interface ends up as phy0.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22705
Signed-off-by: Robert Marko <robimarko@gmail.com>
All targets using ar8327 use OF.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22069
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix execution of initramfs image on Huawei AP5030DN and AP6010DN by
increasing available memory for LZMA extraction by the loader.
The default leaves only ~23.6 MB between the decompression target
and the running loader code. Extracting images with built-in
packages lead to overwriting the loader code. This causes
the decompression to produce garbage output and hang.
Fix this by overwriting LZMA_TEXT_START to increase the
available memory for LZMA extraction to ~39.6 MB.
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
Link: https://github.com/openwrt/openwrt/pull/22581
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These targets seems to be left over, so changed as other targets
covered by commit d35d92a .
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/22510
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, devices having two cpu ports to the switch managed by swconfig,
especally those with qca955x, line tplink archer c7 v2 and linksys ea4500 v3,
use vlan on different cpu port to separate networks by default. (e.g. eth1.1
for lan, eth0.2 for wan)
However, untagging to these vlans cpu ports, and limiting vlans in the switch
on these devices could effectively offload the expense to process vlan tag from
cpu to the switch, and increase the throughput of lan <-> wan ipoe routing.
Tested on my tplink tl-wdr4900 v2, where ucidef_add_switch "switch0"
"0u@eth1" "2:lan" "3:lan" "4:lan" "5:lan" "6u@eth0" "1:wan" finally generates
on /etc/config/network:
config device
option name 'br-lan'
option type 'bridge'
list ports 'eth1'
config interface 'lan'
option device 'br-lan'
option proto 'static'
list ipaddr '192.168.1.1/24'
option ip6assign '60'
config interface 'wan'
option device 'eth0'
option proto 'dhcp'
config interface 'wan6'
option device 'eth0'
option proto 'dhcpv6'
config switch
option name 'switch0'
option reset '1'
option enable_vlan '1'
config switch_vlan
option device 'switch0'
option vlan '1'
option ports '2 3 4 5 0'
config switch_vlan
option device 'switch0'
option vlan '2'
option ports '1 6'
and the throughput of lan <-> wan ipoe routing with software flow offload
increases from around
[850 Mbps](https://openwrt.org/toh/tp-link/archer-c5-c7-wdr7500#nat_performance)
to 900 Mbps.
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/19444
Signed-off-by: Robert Marko <robimarko@gmail.com>
Bump compat version to 3.0 for TP-Link RE355 v1, RE450 v1 and RE450 v2.
Was missed for 25.12; users upgrading from older images need sysupgrade -F.
Signed-off-by: Ivan Diaz <diaz.it@icloud.com>
Link: https://github.com/openwrt/openwrt/pull/22185
Signed-off-by: Robert Marko <robimarko@gmail.com>
Misaligned rootfs_data caused config loss on sysupgrade. Set BLOCKSIZE
:= 4k for proper JFFS2 alignment. Add DEVICE_COMPAT_MESSAGE for
sysupgrade -F requirement.
Signed-off-by: Ivan Diaz <diaz.it@icloud.com>
Link: https://github.com/openwrt/openwrt/pull/22185
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rename Device/tplink_rex5x-v1 to tplink_rex5x. Make RE355 v1, RE450 v1,
and RE450 v2 inherit from it, removing duplicated fields from RE450 v2.
Signed-off-by: Ivan Diaz <diaz.it@icloud.com>
Link: https://github.com/openwrt/openwrt/pull/22185
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh kernel patches with make target/linux/refresh for each target.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22206
Signed-off-by: Robert Marko <robimarko@gmail.com>
The GPIO cascade driver is a downstream-only driver and the Buffalo
WZR-HP-G300NH is its only user for now. Recently, a similar and
independently developed driver 'gpio-line-mux `which serves the same
purpose was accepted upstream and backported here. Use that instead the
downstream driver.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22206
Signed-off-by: Robert Marko <robimarko@gmail.com>
Instead of redifining the DEVICE_PACKAGES, make sure to expand the list
so yafut is included by default as well.
Fixes: 42cd48678745 ("ath79: remove kmod-ath9k and wpad from Mikrotik RB750r2")
Signed-off-by: Robert Marko <robimarko@gmail.com>
The RB750r2 (HEXLite) does not have wifi and those packages bloat the image
by a significant amount. When building a custom image with WireGuard and
booting that from initramfs, there wasn't enough space left in tmpfs to
upload and flash the squashfs image. Investigating what packages I could
remove, I discovered these unneeded ones.
Signed-off-by: Eicke Herbertz <wolletd@posteo.de>
Link: https://github.com/openwrt/openwrt/pull/22134
Signed-off-by: Robert Marko <robimarko@gmail.com>
NVMEM in UBI support has been present for a while. Use it to get the
MACs. Seems caldata needs to continue to be obtained through userspace.
This fixes label-mac-device as it needs a mac-address nvmem cell.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17068
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Linux kernel assumes that the u-boot environment covers the full
partition, but it only covers 0x1000 bytes. Linux checks the CRC and
does this over the full partition. This fails like this:
```
u-boot-env-layout 1f000000.spi:flash@0:partitions:partition@30000:nvmem-layout: Invalid calculated CRC32: 0xfcac8c41 (expected: 0x14e6335a)
u-boot-env-layout 1f000000.spi:flash@0:partitions:partition@30000:nvmem-layout: probe with driver u-boot-env-layout failed with error -22
```
Define the u-boot environment with a length of 0x1000 bytes to calculate
the CRC only over this area.
When replicating the u-boot environment with these parameters it
generates the same CRC:
```
mkenvimage -p 0 -b -s 0x1000 -o output.bin input.txt
```
Fixes: https://github.com/openwrt/openwrt/issues/21696
Fixes: 5e3a602def72 ("ath79: sitecom,wlrx100: use nvmem")
Link: https://github.com/openwrt/openwrt/pull/22030
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Though most Macronix Flash support the lock feature, the generic lock
implementation is not fully compatible with the Macronix series Flash.
Enabling the lock feature globally is unsafe. These hack patches are
used to unlock the Flash of ubnt devices on the ath79 target. Rework
these patches and move it to the ath79 target to prevent the potential
risk.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21754
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This header is deprecated and typically platform_device.h should be
used.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21164
[Adapted the lantiq patches a bit]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now that we have a board file, add calibration variant for TP-Link
TL-WA1201 v2 and add ipq-wifi package for it.
Tested-by: Jim McDonald <122668301+jimmyd998@users.noreply.github.com>
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21736
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add devm for ioremap to proper cleanup.
Test gpiod_direction_input for failure.
Remove rb91x_nand_release and fix wrong usage.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21165
Signed-off-by: Robert Marko <robimarko@gmail.com>
