That's similar to what was done for conn_streams and connections. The
flags were only set exactly when the relevant pointers were allocated,
so better test the pointer than the flag and stop setting the flag.
Just like for the conn_stream, now that these addresses are dynamically
allocated, there is no single case where the pointer is set without the
corresponding flag, and the flag is used as a permission to dereference
the pointer. Let's just replace the test of the flag with a test of the
pointer and remove all flag assignment. This makes the code clearer
(especially in "if" conditions) and saves the need for future code to
think about properly setting the flag after setting the pointer.
This adds a deinit_idle_conns() function that's called on deinit to
release the per-thread idle connection management tasks. The global
task was already taken care of.
Some older systems may routinely return EWOULDBLOCK for some syscalls
while we tend to check only for EAGAIN nowadays. Modern systems define
EWOULDBLOCK as EAGAIN so that solves it, but on a few older ones (AIX,
VMS etc) both are different, and for portability we'd need to test for
both or we never know if we risk to confuse some status codes with
plain errors.
There were few entries, the most annoying ones are the switch/case
because they require to only add the entry when it differs, but the
other ones are really trivial.
The issue only concerns the backend connection. The conn-stream is now owned
by the stream and persists during all the stream life. Thus we must not
crush it when the backend connection is released.
It is 2.6-specific. No backport is needed.
The source and destination addresses at the applicative layer are moved from
the stream-interface to the conn-stream. This simplifies a bit the code and
it is a logicial step to remove the stream-interface.
It was supposed to be there, and probably was not placed there due to
historic limitations in listener_accept(), but now there does not seem
to be a remaining valid reason for keeping the quic_conn out of the
handle. In addition in new_quic_cli_conn() the handle->fd was incorrectly
set to the listener's FD.
Certain functions cannot be called on an FD-less conn because they are
normally called as part of the protocol-specific setup/teardown sequence.
Better place a few BUG_ON() to make sure none of them is called in other
situations. If any of them would trigger in ambiguous conditions, it would
always be possible to replace it with an error.
In "haproxy -vv" we produce a list of available muxes with their
capabilities, but that list is often quite large for terminals due
to excess of spaces, so let's reduce them a bit to make the output
more readable.
This one is referenced in initcalls by its pointer, it makes no sense
to declare it inline. At best it causes function duplication, at worst
it doesn't build on older compilers.
With BUG_ON() being enabled by default it is more useful to use a BUG_ON()
instead of an effectively never-taken if, as any incorrect assumptions will
become much more visible.
see 488ee7fb6 ("BUG/MAJOR: proxy_protocol: Properly validate TLV lengths")
Transform the unreachability comment into a call to `my_unreachable()` to allow
the compiler from benefitting from it.
see d1b15b6e9 ("MINOR: proxy_protocol: Ingest PP2_TYPE_UNIQUE_ID on incoming connections")
see 615f81eb5 ("MINOR: connection: Use a `struct ist` to store proxy_authority")
Thanks to all previous changes, it is now possible to move the
stream-interface into the conn-stream. To do so, some SI functions are
removed and their conn-stream counterparts are added. In addition, the
conn-stream is now responsible to create and release the
stream-interface. While the stream-interfaces were inlined in the stream
structure, there is now a pointer in the conn-stream. stream-interfaces are
now dynamically allocated. Thus a dedicated pool is added. It is a temporary
change because, at the end, the stream-interface structure will most
probably disappear.
frontend and backend conn-streams are now directly accesible from the
stream. This way, and with some other changes, it will be possible to remove
the stream-interfaces from the stream structure.
Thanks to previous changes, it is now possible to set an appctx as endpoint
for a conn-stream. This means the appctx is no longer linked to the
stream-interface but to the conn-stream. Thus, a pointer to the conn-stream
is explicitly stored in the stream-interface. The endpoint (connection or
appctx) can be retrieved via the conn-stream.
Let's not use a trash there anymore. The function is called at very
early boot (for "haproxy -vv"), and the need for a trash prevents the
arguments from being parsed earlier. Moreover, the function only uses
a FILE* on output with fprintf(), so there's not even any benefit in
using chunk_printf() on an intermediary variable, emitting the output
directly is both clearer and safer.
Commit 3d2093af9 ("MINOR: connection: Add a connection error code sample
fetch") added these convenient sample-fetch functions but it appears that
due to a misunderstanding the redundant "conn" part was kept in their
name, causing confusion, since "fc" already stands for "front connection".
Let's simply call them "fc_err" and "bc_err" to match all other related
ones before they appear in a final release. The VTC they appeared in were
also updated, and the alpha sort in the keywords table updated.
Cc: William Lallemand <wlallemand@haproxy.org>
Add a new parameter force_mux_ops. This will be useful to specify an
alternative to the srv->mux_proto field. If non-NULL, it will be use to
force the mux protocol wether srv->mux_proto is set or not.
This argument will become useful to install a mux for non-standard
streams, most notably websocket streams.
Implement a new function to update the ALPN on an existing connection.
on an existing connection. The ALPN from the ssl context can be checked
to update the ALPN only if it is a subset of the context value.
This method will be useful to change a connection ALPN for websocket,
must notably if the server does not support h2 websocket through the
rfc8441 Extended Connect.
Just like for the PROXY protocol, when the NetScaler Client IP insertion
header is received, the retrieved client source and destination addresses
are set at the session level. This leaves those at the connection level
intact.
When PROXY protocol line is received, the retrieved client source and
destination addresses are set at the session level. This leaves those at the
connection level intact.
If the stream exists, the frontend stream-interface is used to get the
client source and destination addresses when the proxy line is built. For
now, stream-interface or session addresses are never set. So, thanks to the
fallback mechanism, no changes are expected with this patch. But its purpose
is to rely on addresses at the appropriate level when set instead of those
at the connection level.
Remove the zeroing of an idle connection node on remove from a tree.
This is not needed and should improve slightly the performance of idle
connection usage. Besides, it breaks the memory poisoning feature.
The remaining large functions are those allocating/initializing and
occasionally freeing connections, conn_streams and sockaddr. Let's
move them to connection.c. In fact, cs_free() is the only one-liner
but let's move it along with the other ones since a call will be
small compared to the rest of the work done there.
The following inlined functions are particularly large (and probably not
inlined at all by the compiler), and together represent roughly half of
the file, while they're used at most once per connection. They were moved
to connection.c.
conn_upgrade_mux_fe, conn_install_mux_fe, conn_install_mux_be,
conn_install_mux_chk, conn_delete_from_tree, conn_init, conn_new,
conn_free
We do not really need to have them inlined, and having xxhash.h included
by connection.h results in this 4700-lines file being processed 101 times
over the whole project, which accounts for 13.5% of the total size!
Additionally, half of the functions are only needed from connection.c.
Let's move the functions there and get rid of the painful include.
The build time is now down to 6.2s just due to this.
The hash type stored everywhere is XXH64_hash_t, which annoyingly forces
everyone to include the huge xxhash file. We know it's an uint64_t because
that's its purpose and the type is only made to abstract it on machines
where uint64_t is not availble. Let's switch the type to uint64_t
everywhere and avoid including xxhash from the type file.
This one doesn't use anything from an SSL context, it only checks the
type of the transport layer of a connection, thus it belongs to
connection.h. This is particularly visible due to all the ifdefs
around it in various call places.
We'll need to improve the API to pass other arguments in the future, so
let's start to adapt better to the current use cases. task_new() is used:
- 18 times as task_new(tid_bit)
- 18 times as task_new(MAX_THREADS_MASK)
- 2 times with a single bit (in a loop)
- 1 in the debug code that uses a mask
This patch provides 3 new functions to achieve this:
- task_new_here() to create a task on the calling thread
- task_new_anywhere() to create a task to be run anywhere
- task_new_on() to create a task to run on a specific thread
The change is trivial and will allow us to later concentrate the
required adaptations to these 3 functions only. It's still possible
to call task_new() if needed but a comment was added to encourage the
use of the new ones instead. The debug code was not changed and still
uses it.
Move the code to allocate/free the mux cleanup task outside of the polling
loop. A new thread_alloc/free handler is registered for this in
connection.c.
This has the benefit to clean up the polling loop code. And as another
benefit, if the task allocation fails, the handler can report an error
to exit the haproxy process. This prevents a potential null pointer
dereferencing.
This should fix the github issue #1389.
This must be backported up to 2.4.
The bc_conn_err and bc_conn_err_str sample fetches give the status of
the connection on the backend side. The error codes and error messages
are the same than the ones that can be raised by the fc_conn_err fetch.
The fc_conn_err and fc_conn_err_str sample fetches give information
about the problem that made the connection fail. This information would
previously only have been given by the error log messages meaning that
thanks to these fetches, the error log can now be included in a custom
log format. The log strings were all found in the conn_err_code_str
function.
This function appends to a buffer some information from a connection.
This will be used by traces and possibly some debugging as well. A
frontend/backend/server, transport/control layers, source/destination
ip:port, connection pointer and direction are reported depending on
the available information.
No idea why this was put inlined into connection.h, it's used only once
for haproxy -vv, and requires tools.h, causing an undesired dependency
from connection.h. Let's move it to connection.c instead where it ought
to have been.
Implement a safe mechanism to close front idling connection which
prevents the soft-stop to complete. Every h1/h2 front connection is
added in a new per-thread list instance. On shutdown, a new task is
waking up which calls wake mux operation on every connection still
present in the new list.
A new stopping_list attach point has been added in the connection
structure. As this member is only used for frontend connections, it
shared the same union as the session_list reserved for backend
connections.
bc_http_major sample fetch now works when it is called from a
tcp-check. When it happens, the session origin is a check. The backend
connection is retrieved from the conn-stream attached to the check.
If required, this path may easily be backported as far as 2.2.
fc_http_major and bc_http_major sample fetches return the major digit of the
HTTP version used, respectively, by the frontend and the backend
connections, based on the mux. However, in reality, "2" is returned if the
H2 mux is detected, otherwise "1" is inconditionally returned, regardless
the mux used. Thus, if called for a raw TCP connection, "1" is returned.
To fix this bug, we now get the multiplexer flags, if there is one, to be
sure MX_FL_HTX is set.
I guess it was made this way on purpose when the H2 multiplexer was
introduced in the 1.8 and with the legacy HTTP mode there is no other
solution at the connection level. Thus this patch should be backported as
far as 2.2. For the 2.0, it must be evaluated first because of the legacy
HTTP mode.
The default proxy was passed as a variable to all parsers instead of a
const, which is not without risk, especially when some timeout parsers used
to make some int pointers point to the default values for comparisons. We
want to be certain that none of these parsers will modify the defaults
sections by accident, so it's important to mark this proxy as const.
This patch touches all occurrences found (89).
There are multiple per-thread lists in the listeners, which isn't the
most efficient in terms of cache, and doesn't easily allow to store all
the per-thread stuff.
Now we introduce an srv_per_thread structure which the servers will have an
array of, and place the idle/safe/avail conns tree heads into. Overall this
was a fairly mechanical change, and the array is now always initialized for
all servers since we'll put more stuff there. It's worth noting that the Lua
code still has to deal with its own deinit by itself despite being in a
global list, because its server is not dynamically allocated.
