Some wrong operations were performed on buffers, assuming the
offsets were relative to the beginning of the request while they
are relative to the beginning of the buffer. In practice this is
not yet an issue since both are the same... until we add support
for keep-alive.
It's not enough to know if the connection will be in CLOSE or TUNNEL mode,
we still need to know whether we want to read a full message to a known
length or read it till the end just as in TUNNEL mode. Some updates to the
RFC clarify slightly better the corner cases, in particular for the case
where a non-chunked encoding is used last.
Now we also take care of adding a proper "connection: close" to messages
whose size could not be determined.
Chunked encoding can be slightly more complex than what was implemented.
Specifically, it supports some optional extensions that were not parsed
till now if present, and would have caused an error to be returned.
Also, now we enforce check for too large values in chunk sizes in order
to ensure we never overflow.
Last, we're now able to return a request error if we can't read the
chunk size because the buffer is already full.
This state indicates that an HTTP message (request or response) is
complete. This will be used to know when we can re-initialize a
new transaction. Right now we only switch to it after the end of
headers if there is no data. When other analysers are implemented,
we can switch to this state too.
The condition to reuse a connection is when the response finishes
after the request. This will have to be checked when setting the
state.
The response 1xx was set too low and required a lot of tests along
the code in order to avoid some processing. We still left the test
after the response rewrite rules so that we can eliminate unwanted
headers if required.
This code really belongs to the http part since it's transaction-specific.
This will also make it easier to later reinitialize a transaction in order
to support keepalive.
We used to apply a limit to each buffer's size in order to leave
some room to rewrite headers, then we used to remove this limit
once the session switched to a data state.
Proceeding that way becomes a problem with keepalive because we
have to know when to stop reading too much data into the buffer
so that we can leave some room again to process next requests.
The principle we adopt here consists in only relying on to_forward+send_max.
Indeed, both of those data define how many bytes will leave the buffer.
So as long as their sum is larger than maxrewrite, we can safely
fill the buffers. If they are smaller, then we refrain from filling
the buffer. This means that we won't risk to fill buffers when
reading last data chunk followed by a POST request and its contents.
The only impact identified so far is that we must ensure that the
BF_FULL flag is correctly dropped when starting to forward. Right
now this is OK because nobody inflates to_forward without using
buffer_forward().
Up to now, we only had a flag in the session indicating if it had to
work in "connection: close" mode. This is not at all compatible with
keep-alive.
Now we ensure that both sides of a connection act independantly and
only relative to the transaction. The HTTP version of the request
and response is also correctly considered. The connection already
knows several modes :
- tunnel (CONNECT or no option in the config)
- keep-alive (when permitted by configuration)
- server-close (close the server side, not the client)
- close (close both sides)
This change carefully detects all situations to find whether a request
can be fully processed in its mode according to the configuration. Then
the response is also checked and tested to fix corner cases which can
happen with different HTTP versions on both sides (eg: a 1.0 client
asks for explicit keep-alive, and the server responds with 1.1 without
a header).
The mode is selected by a capability elimination algorithm which
automatically focuses on the least capable agent between the client,
the frontend, the backend and the server. This ensures we won't get
undesired situtations where one of the 4 "agents" is not able to
process a transaction.
No "Connection: close" header will be added anymore to HTTP/1.0 requests
or responses since they're already in close mode.
The server-close mode is still not completely implemented. The response
needs to be rewritten as keep-alive before being sent to the client if
the connection was already in server-close (which implies the request
was in keep-alive) and if the response has a content-length or a
transfer-encoding (but only if client supports 1.1).
A later improvement in server-close mode would probably be to detect
some situations where it's interesting to close the response (eg:
redirections with remote locations). But even then, the client might
close by itself.
It's also worth noting that in tunnel mode, no connection header is
affected in either direction. A tunnelled connection should theorically
be notified at the session level, but this is useless since by definition
there will not be any more requests on it. Thus, we don't need to add a
flag into the session right now.
Now that the HTTP analyser will already have parsed the beginning
of the request body, we don't have to check for transfer-encoding
anymore since we have the current chunk size in hdr_content_len.
The POST body analysis was split between two analysers for historical
reasons. Now we only have one analyser which checks content length
and waits for enough data to come.
Right now this analyser waits for <url_param_post_limit> bytes of
body to reach the buffer, or the first chunk. But this could be
improved to wait for any other amount of data or any specific
contents.
The previous check was correct: the RFC states that it is required
to have a domain-name which contained a dot AND began with a dot.
However, currently some (all?) browsers do not obey this specification,
so such configuration might work.
This patch reverts 3d8fbb6658 but
changes the check from FATAL to WARNING and extends the message.
Fix 500b8f0349 fixed the patch for the 64 bit
case but caused the opposite type issue to appear on 32 bit platforms. Cast
the difference and be done with it since gcc does not agree on type carrying
the difference between two pointers on 32 and 64 bit platforms.
Implement decreasing health based on observing communication between
HAProxy and servers.
Changes in this version 2:
- documentation
- close race between a started check and health analysis event
- don't force fastinter if it is not set
- better names for options
- layer4 support
Changes in this version 3:
- add stats
- port to the current 1.4 tree
Cyril Bont found that when an error is detected in one config file, it
is also reported in all other ones, which is wrong. The fix obviously
consists in checking the return code from readcfgfile() and not the
accumulator.
Today I was testing headers manipulation but I met a bug with my first test.
To reproduce it, add for example this line :
rspadd Cache-Control:\ max-age=1500
Check the response header, it will provide :
Cache-Control: max-age=15000 <= the last character is duplicated
This only happens when we use backslashes on the last line of the
configuration file, without returning to the line.
Also if the last line is like :
rspadd Cache-Control:\ max-age=1500\
the last backslash causes a segfault.
This is not due to rspadd but to a more general bug in cfgparse.c :
...
if (skip) {
memmove(line + 1, line + 1 + skip, end - (line + skip + 1));
end -= skip;
}
...
should be :
...
if (skip) {
memmove(line + 1, line + 1 + skip, end - (line + skip));
end -= skip;
}
...
I've reproduced it with haproxy 1.3.22 and the last 1.4 snapshot.
In some environments it is not possible to rely on any wildcard for a
domain name (eg: .com, .net, .fr...) so it is required to send multiple
domain extensions. (Un)fortunately the syntax check on the domain name
prevented that from being done the dirty way. So let's just build a
domain list when multiple domains are passed on the same line.
(cherry picked from commit 950245ca2b)
It was a OR instead of a AND, so it was required to have a cookie
name which contained a dot AND began with a dot.
(cherry picked from commit a1e107fc13)
Gabriel Sosa reported that logs were appearing with BADREQ when
'option httplog' was used with a TCP proxy (eg: inherited via a
default instance). This patch detects it and falls back to tcplog
after emitting a warning.
(cherry picked from commit 5f0bd6537f)
Holger Just reported that running ACLs with too many args caused
a segfault during config parsing. This is caused by a wrong test
on argument count. In case of too many arguments on a config line,
the last one was not correctly zeroed. This is now done and we
report the error indicating what part had been truncated.
(cherry picked from commit 3b39c1446b)
Cameron Simpson reported an annoying case where haproxy simply reports
"Error(s) found in configuration file" when the file is not found or
not readable.
Fortunately the parsing function still returns -1 in case of open
error, so we're able to detect the issue from the caller and report
the corresponding errno message.
In order to support keepalive, we'll have to differentiate
normal sessions from tunnel sessions, which are the ones we
don't want to analyse further.
Those are typically the CONNECT requests where we don't care
about any form of content-length, as well as the requests
which are forwarded on non-close and non-keepalive proxies.
To sum up :
- len : it's now the max number of characters for the value, preventing
garbaged results.
- a new option "prefix" is added, this allows to use dynamic cookie
names (e.g. ASPSESSIONIDXXX).
Previously in the thread, I wanted to use the value found with
"capture cookie" but when i started to update the documentation, I
found this solution quite weird. I've made a small rework to not
depend on "capture cookie".
- There's the posssiblity to define the URL parser mode (path parameters
or query string).
We now set msg->col and msg->sov to the first byte of non-header.
They will be used later when parsing chunks. A new macro was added
to perform size additions on an http_msg in order to limit the risks
of copy-paste in the long term.
During this operation, it appeared that the http_msg struct was not
optimal on 64-bit, so it was re-ordered to fill the holes.
Yohan Tordjman at Dstorage found that upgrading haproxy to 1.4-dev4
caused truncated objects to be returned. An strace quickly exhibited
the issue which was 100% reproducible :
4297 epoll_wait(0, {}, 10, 0) = 0
4297 epoll_wait(0, {{EPOLLIN, {u32=7, u64=7}}}, 10, 1000) = 1
4297 splice(0x7, 0, 0x5, 0, 0xffffffffffffffff, 0x3) = -1 EINVAL (Invalid argument)
4297 shutdown(7, 1 /* send */) = 0
4297 close(7) = 0
4297 shutdown(2, 1 /* send */) = 0
4297 close(2) = 0
This is caused by the fact that the forward length is taken from
BUF_INFINITE_FORWARD, which is -1. The problem does not appear
in 32-bit mode because this value is first cast to an unsigned
long, truncating it to 32-bit (4 GB). Setting an upper bound
fixes the issue.
Also, a second error check has been added for splice. If EINVAL
is returned, we fall back to recv().
An HTTP message can be decomposed into several sub-states depending
on the transfer-encoding. We'll have to keep these state information
while parsing chunks, so we must extend the values. In order not to
change everything, we'll now consider that anything >= MSG_BODY is
the body, and that the value indicates the precise state. The
MSG_ERROR status which was greater than MSG_BODY was moved for this.
Right now, an HTTP server cannot track a TCP server and vice-versa.
This patch enables proxy tracking without relying on the proxy's mode
(tcp/http/health). It only requires a matching proxy name to exist. The
original function was renamed to findproxy_mode().
This patch extends and corrects the functionality introduced by
"Collect & provide http response codes received from servers":
- responses are now also accounted for frontends
- backend's and frontend's counters are incremented based
on responses sent to client, not received from servers
This patch adds <a href> html links for proxies, frontends, servers
and backends. Once located, can be clicked. Users no longer have to
manually add #anchor to stat's url.
All files referencing the previous ebtree code were changed to point
to the new one in the ebtree directory. A makefile variable (EBTREE_DIR)
is also available to use files from another directory.
The ability to build the libebtree library temporarily remains disabled
because it can have an impact on some existing toolchains and does not
appear worth it in the medium term if we add support for multi-criteria
stickiness for instance.
We also check the close status and terminate the server persistent
connection if appropriate. Note that since this change, we'll not
get any "Connection: close" headers added to HTTP/1.0 responses
anymore, which is good.
The code part which waits for an HTTP response has been extracted
from the old function. We now have two analysers and the second one
may re-enable the first one when an 1xx response is encountered.
This has been tested and works.
The calls to stream_int_return() that were remaining in the wait
analyser have been converted to stream_int_retnclose().
Store those elements in the transaction. RFC2616 is strictly followed.
Note that requests containing two different content-length fields are
discarded as invalid.
This patch has 2 goals :
1. I wanted to test the appsession feature with a small PHP code,
using PHPSESSID. The problem is that when PHP gets an unknown session
id, it creates a new one with this ID. So, when sending an unknown
session to PHP, persistance is broken : haproxy won't see any new
cookie in the response and will never attach this session to a
specific server.
This also happens when you restart haproxy : the internal hash becomes
empty and all sessions loose their persistance (load balancing the
requests on all backend servers, creating a new session on each one).
For a user, it's like the service is unusable.
The patch modifies the code to make haproxy also learn the persistance
from the client : if no session is sent from the server, then the
session id found in the client part (using the URI or the client cookie)
is used to associated the server that gave the response.
As it's probably not a feature usable in all cases, I added an option
to enable it (by default it's disabled). The syntax of appsession becomes :
appsession <cookie> len <length> timeout <holdtime> [request-learn]
This helps haproxy repair the persistance (with the risk of losing its
session at the next request, as the user will probably not be load
balanced to the same server the first time).
2. This patch also tries to reduce the memory usage.
Here is a little example to explain the current behaviour :
- Take a Tomcat server where /session.jsp is valid.
- Send a request using a cookie with an unknown value AND a path
parameter with another unknown value :
curl -b "JSESSIONID=12345678901234567890123456789012" http://<haproxy>/session.jsp;jsessionid=00000000000000000000000000000001
(I know, it's unexpected to have a request like that on a live service)
Here, haproxy finds the URI session ID and stores it in its internal
hash (with no server associated). But it also finds the cookie session
ID and stores it again.
- As a result, session.jsp sends a new session ID also stored in the
internal hash, with a server associated.
=> For 1 request, haproxy has stored 3 entries, with only 1 which will be usable
The patch modifies the behaviour to store only 1 entry (maximum).
When processing a GET or HEAD request in close mode, we know we don't
need to read anything anymore on the socket, so we can disable it.
Doing this can save up to 40% of the recv calls, and half of the
epoll_ctl calls.
For this we need a buffer flag indicating that we're not interesting in
reading anymore. Right now, this flag also disables both polled reads.
We might benefit from disabling only speculative reads, but we will need
at least this flag when we want to support keepalive anyway.
Currently we don't disable the flag on completion, but it does not
matter as we close ASAP when performing the shutw().
The fd_list[] used by sepoll was indexed on the fd number and was only
used to store the equivalent of an integer. Changing it to be merged
with fdtab reduces the number of pointer computations, the code size
and some initialization steps. It does not harm other pollers much
either, as only one integer was added to the fdtab array.
Some rarely information are stored in fdtab, making it larger for no
reason (source port ranges, remote address, ...). Such information
lie there because the checks can't find them anywhere else. The goal
will be to move these information to the stream interface once the
checks make use of it.
For now, we move them to an fdinfo array. This simple change might
have improved the cache hit ratio a little bit because a 0.5% of
performance increase has measured.
Till now we would only set SN_CONN_CLOSED after rewriting it. Now we
set it just after checking the Connection header so that we can use
the result later if required.
This can ensure that data is readily available on a socket when
we accept it, but a bug in the kernel ignores the timeout so the
socket can remain pending as long as the client does not talk.
Use with care.
This patch makes stats page about 30% smaller and
"CSS 2.1" + "HTML 4.01 Transitional" compliant.
There should be no visible differences.
Changes:
- add DOCTYPE for HTML 4.01 Transitional
- add missing </ul>
- remove cols=, AFAIK no modern browser support this property and
it prevents validation to pass.
- remove "align: center": there is no such property in css. There is
however "text-align: center" but it is definitely not what we would
like to see here.
- by default align .titre to center
- by default align .td to right
- remove all align=right, no longer necessary
- add class=ac (align center): shorter than "align=center" and use it when
necessary
- remove nowrap from td, instead use "white-space: nowrap" in css
Now stats page passes W3C validators for HTML & CSS. We may consider adding
"validated" icons from www.w3.org. ;)
This alone makes a typical HTML stats dump consume 10% CPU less,
because we avoid doing complex printf calls to drop them later.
Only a few common cases have been checked, those which are very
likely to run for nothing.
It is a bit expensive and complex to use to call buffer_feed()
directly from the request parser, and there are risks that some
output messages are lost in case of buffer full. Since most of
these messages are static, let's have a state dedicated to print
these messages and store them in a specific area shared with the
stats in the session. This both reduces code size and risks of
losing output data.
Krzysztof reported that using names only for get weight/set weight
was not enough because it's still possible to have multiple servers
with the same name (and my test config is one of those). He suggested
to be able to designate them by their unique numeric IDs by prefixing
the ID with a dash.
That way we can have :
set weight #120/#2
as well as
get weight static/srv1 10
Capture & display more data from health checks, like
strerror(errno) for L4 failed checks or a first line
from a response for L7 successes/failed checks.
Non ascii or control characters are masked with
chunk_htmlencode() (html stats) or chunk_asciiencode() (logs).
Add two functions to encode input chunk replacing
non-printable, non ascii or special characters
with:
"&#%u;" - chunk_htmlencode
"<%02X>" - chunk_asciiencode
Above functions should be used when adding strings, received
from possible unsafe sources, to html stats or logs.
int get_backend_server(const char *bk_name, const char *sv_name,
struct proxy **bk, struct server **sv);
This function scans the list of backends and servers to retrieve the first
backend and the first server with the given names, and sets them in both
parameters. It returns zero if either is not found, or non-zero and sets
the ones it did not found to NULL. If a NULL pointer is passed for the
backend, only the pointer to the server will be updated.
The stats socket can now run at 3 different levels :
- user
- operator (default one)
- admin
These levels are used to restrict access to some information
and commands. Only the admin can clear all stats. A user cannot
clear anything nor access sensible data such as sessions or
errors.
The most common use of "clear counters" should be to only clear
max values without affecting cumulated values, for instance,
after an incident. So we change "clear counters" to only clear
max values, and add "clear counters all" to clear all counters.
I noticed that in __eb32_insert , if the tree is empty
(root->b[EB_LEFT] == NULL) , the node.bit is not defined.
However in __task_queue there are checks:
- if (last_timer->node.bit < 0)
- if (task->wq.node.bit < last_timer->node.bit)
which might rely upon an undefined value.
This is how I see it:
1. We insert eb32_node in an empty wait queue tree for a task (called by
process_runnable_tasks() ):
Inserting into empty wait queue &task->wq = 0x72a87c8, last_timer
pointer: (nil)
2. Then, we set the last timer to the same address:
Setting last_timer: (nil) to: 0x72a87c8
3. We get a new task to be inserted in the queue (again called by
process_runnable_tasks()) , before the __task_unlink_wq() is called for
the previous task.
4. At this point, we still have last_timer set to 0x72a87c8 , but since
it was inserted in an empty tree, it doesn't have node.bit and the
values above get dereferenced with undefined value.
The bug has no effect right now because the check for equality is still
made, so the next timer will still be queued at the right place anyway,
without any possible side-effect. But it's a pending bug waiting for a
small change somewhere to strike.
Iliya Polihronov
These ACLs are used to check the number of active connections on the
frontend, backend or in a backend's queue. The avg_queue returns the
average number of queued connections per server, and for this, divides
the total number of queued connections by the number of alive servers.
The dst_conn ACL has been slightly changed to more reflect its name and
original usage, which is to return the number of connections on the
destination address/port (the socket) and not the whole frontend.
Consistent hashing provides some interesting advantages over common
hashing. It avoids full redistribution in case of a server failure,
or when expanding the farm. This has a cost however, the hashing is
far from being perfect, as we associate a server to a request by
searching the server with the closest key in a tree. Since servers
appear multiple times based on their weights, it is recommended to
use weights larger than approximately 10-20 in order to smoothen
the distribution a bit.
In some cases, playing with weights will be the only solution to
make a server appear more often and increase chances of being picked,
so stats are very important with consistent hashing.
In order to indicate the type of hashing, use :
hash-type map-based (default, old one)
hash-type consistent (new one)
Consistent hashing can make sense in a cache farm, in order not
to redistribute everyone when a cache changes state. It could also
probably be used for long sessions such as terminal sessions, though
that has not be attempted yet.
More details on this method of hashing here :
http://www.spiteful.com/2008/03/17/programmers-toolbox-part-3-consistent-hashing/
Commit 404e8ab461 introduced
smart checking for stupid acl typos. However, now haproxy shows
the warning even for valid acls, like this one:
acl Cookie-X-NoAccel hdr_reg(cookie) (^|\ |;)X-NoAccel=1(;|$)
If a frontend does not set 'option socket-stats', a 'clear counters'
on the stats socket could segfault because li->counters is NULL. The
correct fix is to check for NULL before as this is a valid situation.
Recent "struct chunk rework" introduced a NULL pointer dereference
and now haproxy segfaults if auth is required for stats but not found.
The reason is that size_t cannot store negative values, but current
code assumes that "len < 0" == uninitialized.
This patch fixes it.
There are a few remaining max values that need to move to counters.
Also, the counters are more often used than some config information,
so get them closer to the other useful struct members for better cache
efficiency.
Until now it was required that every custom ID was above 1000 in order to
avoid conflicts. Now we have the list of all assigned IDs and can automatically
pick the first unused one. This means that it is perfectly possible to interleave
automatic IDs with persistent IDs and the parser will automatically allocate
unused values starting with 1.
When a name or ID conflict is detected, it is sometimes useful to know
where the other one was declared. Now that we have this information,
report it in error messages.
This patch allows to collect & provide separate statistics for each socket.
It can be very useful if you would like to distinguish between traffic
generate by local and remote users or between different types of remote
clients (peerings, domestic, foreign).
Currently no "Session rate" is supported, but adding it should be possible
if we found it useful.
Doing this, we can remove the last BF_HIJACK user and remove
produce_content(). s->data_source could also be removed but
it is currently used to detect if the stats or a server was
used.
The stats handler used to store internal states in s->ana_state. Now
we only rely on si->st0 in which we can store as many states as we
have possible outputs. This cleans up the stats code a lot and makes
it more maintainable. It has also reduced code size by a few hundred
bytes.
We can simplify the code in the stats functions using buffer_feed_chunk()
instead of buffer_write_chunk(). Let's start with this function. This
patch also fixed an issue where we could dump past the end of the capture
buffer if it is shorter than the captured request.
In old versions, before 1.3.16, we had to refresh the timeouts after
each call to process_session() because the stream socket handler did
not do it. Now that the sockets can exchange data for a long period
without calling process_session(), we can detect an old activity and
refresh a timeout long after the last activity, causing too late a
detection of some timeouts.
The fix simply consists in not checking for activity anymore in
stream_sock_data_finish() but only set a timeout if it was not
previously set.
Calling buffer_shutw() marks the buffer as closed but if it was already
closed in the other direction, the stream interface is not marked as
closed, causing infinite loops.
We took this opportunity to completely remove buffer_shutw() and buffer_shutr()
which have no reason to be used at all and which will always cause trouble
when directly called. The stats occurrence was the last one.
By default, when data is sent over a socket, both the write timeout and the
read timeout for that socket are refreshed, because we consider that there is
activity on that socket, and we have no other means of guessing if we should
receive data or not.
While this default behaviour is desirable for almost all applications, there
exists a situation where it is desirable to disable it, and only refresh the
read timeout if there are incoming data. This happens on sessions with large
timeouts and low amounts of exchanged data such as telnet session. If the
server suddenly disappears, the output data accumulates in the system's
socket buffers, both timeouts are correctly refreshed, and there is no way
to know the server does not receive them, so we don't timeout. However, when
the underlying protocol always echoes sent data, it would be enough by itself
to detect the issue using the read timeout. Note that this problem does not
happen with more verbose protocols because data won't accumulate long in the
socket buffers.
When this option is set on the frontend, it will disable read timeout updates
on data sent to the client. There probably is little use of this case. When
the option is set on the backend, it will disable read timeout updates on
data sent to the server. Doing so will typically break large HTTP posts from
slow lines, so use it with caution.
During troubleshooting, it's often useful to get the list of supported
pollers but until now it was required to have a working configuration
first. Since the pollers are known before main() is called, let's list
them with the build options.
The "static-rr" is just the old round-robin algorithm. It is still
in use when a hash algorithm is used and the data to hash is not
present, but it was impossible to configure it explicitly. This one
is cheaper in terms of CPU and supports unlimited numbers of servers,
so it makes sense to be able to use it.
LB algo macros were composed of the LB algo by itself without any indication
of the method to use to look up a server (the lb function itself). This
method was implied by the LB algo, which was not very convenient to add
more algorithms. Now we have several fields in the LB macros, some to
describe what to look for in the requests, some to describe how to transform
that (kind of algo) and some to describe what lookup function to use.
The next patch will make it possible to factor out some code for all algos
which rely on a map.
The lbprm structure has moved to backend.h, where it should be, and
all algo-specific types and declarations have moved to their specific
files. The proxy struct is now much more readable.
This patch implements "description" (proxy and global) and "node" (global)
options, removes "node-name" and adds "show-node" & "show-desc" options
for "stats". It also changes the way the header lines (with proxy name) and
the statistics are displayed, so stats no longer look so clumsy with very
long names.
Instead of "node-name" it is possible to use show-node/show-desc with
an optional parameter that overrides a default node/description.
backend cust-0045
# report specific values for this customer
stats show-node Europe
stats show-desc Master node for Europe, Asia, Africa
We need to remove hash map accesses out of backend.c if we want to
later support new hash methods. This patch separates the hash computation
method from the server lookup. It leaves the lookup function to lb_map.c
and calls it with the result of the hash.
It was becoming painful to have all the LB algos in backend.c.
Let's move them to their own files. A few hashing functions still
need be broken in two parts, one for the contents and one for the
map position.
The code was duplicated serveral times, let's use
server_status_printf() instead.
text data bss dec hex filename
263504 5800 64224 333528 516d8 haproxy-old
262944 5800 64224 332968 514a8 haproxy-new
Depends on "struct chunk rework" and
"Health check reporting code rework + health logging, v3"
Check if rise/fall has an argument and it is > 0 or bad things may happen
in the health checks. ;)
Now it is verified and the code no longer allows for such condition:
backend bad
(...)
server o-f0 192.168.129.27:80 check inter 4000 source 0.0.0.0 rise 0
server o-r0 192.168.129.27:80 check inter 4000 source 0.0.0.0 fall 0
server o-f1 192.168.129.27:80 check inter 4000 source 0.0.0.0 rise
server o-r1 192.168.129.27:80 check inter 4000 source 0.0.0.0 fall
[ALERT] 269/161830 (24136) : parsing [../git/haproxy.cfg:98]: 'rise' has to be > 0.
[ALERT] 269/161830 (24136) : parsing [../git/haproxy.cfg:99]: 'fall' has to be > 0.
[ALERT] 269/161830 (24136) : parsing [../git/haproxy.cfg:100]: 'rise' expects an integer argument.
[ALERT] 269/161830 (24136) : parsing [../git/haproxy.cfg:101]: 'fall' expects an integer argument.
Also add endline in the custom id checking code.
This patch adds health logging so it possible to check what
was happening before a crash. Failed healt checks are logged if
server is UP and succeeded healt checks if server is DOWN,
so the amount of additional information is limited.
I also reworked the code a little:
- check_status_description[] and check_status_info[] is now
joined into check_statuses[]
- set_server_check_status updates not only s->check_status and
s->check_duration but also s->result making the code simpler
Changes in v3:
- for now calculate and use local versions of health/rise/fall/state,
it is a slow path, no harm should be done. One day we may centralize
processing of the checks and remove the duplicated code.
- also log checks that are restoring current state
- use "conditionally succeeded" for 404 with disable-on-404
There is no reason to inline functions which are used to grab a server
depending on an LB algo. They are large and used at several places.
Uninlining them saves 400 bytes of code.
Due to a misplaced call to stream_int_retnclose(), the stats output
buffer was erased before each call to produce_content(), resulting
in missing pieces in the stats output if the connection was not
fast enough between haproxy and the client.
We can get rid of the stats analyser by moving all the stats code
to a stream interface applet. Above being cleaner, it provides new
advantages such as the ability to process requests and responses
from the same function and work only with simple state machines.
There's no need for any hijack hack anymore.
The direct advantage for the user are the interactive mode and the
ability to chain several commands delimited by a semi-colon. Now if
the user types "prompt", he gets a prompt from which he can send
as many requests as he wants. All outputs are terminated by a
blank line followed by a new prompt, so this can be used from
external tools too.
The code is not very clean, it needs some rework, but some part
of the dirty parts are due to the remnants of the hijack mode used
in the old functions we call.
The old AN_REQ_STATS_SOCK analyser flag is now unused and has been
removed.
We will need to modify the stats dump functions so that they can
be used in interactive mode. For this, we want their caller to
prepare the connection for a close, not themselves to do it.
Let's simply move the stream_int_retnclose() out.
Currently, it's up to process_session() to call the internal tasks
if any are associated to the task being processed. If such a task
is referenced, we don't use ->update() in process_session(), but
only ->iohandler(), which itself is free to use ->update() to
complete its work.
It it also important to understand that an I/O handler may wake the
task up again, for instance because it tries to send data to the
other stream interface, which itself will wake the task up. So
after returning from ->iohandler(), we must check if the task has
been sent back to the runqueue, and if so, immediately return.
It will soon be necessary to have stream interfaces running as part of
the current task, or as independant tasks. For instance when we want to
implement compression or SSL. It will also be used for applets running
as stream interfaces.
These new functions are used to perform exactly that. Note that it's
still not easy to write a simple echo applet and more functions will
likely be needed.
When stream interfaces will embedded applets running as part as their
holding task, we'll need a new callback to process them from the
session processor.
We had to add a new stream_interface flag : SI_FL_DONT_WAKE. This flag
is used to indicate that a stream interface is being updated and that
no wake up should be sent to its owner. This will be required for tasks
embedded into stream interfaces. Otherwise, we could have the
owner task send wakeups to itself during status updates, thus
preventing the state from converging. As long as a stream_interface's
status is being monitored and adjusted, there is no reason to wake it
up again, as we know its changes will be seen and considered.
Those two functions did not correctly deal with full buffers and/or
buffers that wrapped around. Buffer_skip() was even able to incorrectly
set buf->w further than the end of buffer if its len argument was wrong,
and buffer_si_getline() was able to incorrectly return a length larger
than the effective buffer data available.
It's important that these functions set these flags themselves, otherwise
the callers will always have to do this, and there is no valid reason for
not doing it.
Commit 27a674efb8 introduced the ability
to configure buffer sizes. Unfortunately, the pool was created before
the conf was read, so that is was always set to the default size.
In order to fix that, we delay the call to init_buffer(), which is not
a problem since nothing uses it during the initialization.
Collect information about last health check result,
including L7 code if possible (for example http or smtp
return code) and time took to finish last check.
Health check info is provided on both stats pages (html & csv)
and logged when a server is marked UP or DOWN. Currently active
check are marked with an asterisk, but only in html mode.
Currently there are 14 status codes:
UNK -> unknown
INI -> initializing
SOCKERR -> socket error
L4OK -> check passed on layer 4, no upper layers testing enabled
L4TOUT -> layer 1-4 timeout
L4CON -> layer 1-4 connection problem, for example "Connection refused"
(tcp rst) or "No route to host" (icmp)
L6OK -> check passed on layer 6
L6TOUT -> layer 6 (SSL) timeout
L6RSP -> layer 6 invalid response - protocol error
L7OK -> check passed on layer 7
L7OKC -> check conditionally passed on layer 7, for example
404 with disable-on-404
L7TOUT -> layer 7 (HTTP/SMTP) timeout
L7RSP -> layer 7 invalid response - protocol error
L7STS -> layer 7 response error, for example HTTP 5xx
In TCP, we don't want to forward chunks of data, we want to forward
indefinitely. This patch introduces a special value for the amount
of data to be forwarded. When buffer_forward() is called with
BUF_INFINITE_FORWARD, it configures the buffer to never stop
forwarding until the end.
An abort during a connect would go to the SI_ST_CLO state without
the buffers shut. This was causing some sessions to never end if
they would abort before the connect request was initiated. This
bug has been introduced after 1.4-dev2.
The doc has been extended to reflect that too.
The BF_EMPTY flag was once used to indicate an empty buffer. However,
it was used half the time as meaning the buffer is empty for the reader,
and half the time as meaning there is nothing left to send.
"nothing to send" is only indicated by "->send_max=0 && !pipe". Once
we fix this, we discover that the flag is not used anymore. So the
flags has been renamed BF_OUT_EMPTY and means exactly the condition
above, ie, there is nothing to send.
Doing so has allowed us to remove some unused tests for emptiness,
but also to uncover a certain amount of situations where the flag
was not correctly set or tested.
The BF_WRITE_ENA buffer flag became very complex to deal with, because
it was used to :
- enable automatic connection
- enable close forwarding
- enable data forwarding
The last point was not very true anymore since we introduced ->send_max,
but still the test remained everywhere. This was causing issues such as
impossibility to connect without forwarding data, impossibility to prevent
closing when data was forwarded, etc...
This patch clarifies the situation by getting rid of this multi-purpose
flag and replacing it with :
- data forwarding based only on ->send_max || ->pipe ;
- a new BF_AUTO_CONNECT flag to allow automatic connection and only
that ;
- ability to perform an automatic connection when ->send_max or ->pipe
indicate that data is waiting to leave the buffer ;
- a new BF_AUTO_CLOSE flag to let the producer automatically set the
BF_SHUTW_NOW flag when it gets a BF_SHUTR.
During this cleanup, it was discovered that some tests were performed
twice, or that the BF_HIJACK flag was still tested, which is not needed
anymore since ->send_max replcaed it. These places have been fixed too.
These cleanups have also revealed a few areas where the other flags
such as BF_EMPTY are not cleanly used. This will be an opportunity for
a second patch.
By inlining this function and slightly reordering it, we can double
the getchar/putchar test throughput, and reduce its footprint by about
40 bytes. Also, it was the only non-inlined char-based function, which
now makes it more consistent this time.
HTTP supports status codes 100 and 101 to report protocol indications,
which are followed by the requests's response. Till now, haproxy would
only see those responses without parsing subsequent ones. That means
that cookie additions were only performed on 1xx messages for instance,
which does not work since headers must be ignored with 1xx messages.
Also, logs were not terribly useful with the common 100 status code
in response to "Expect: 100-continue" during POST some requests.
This change adds support for such messages. Now haproxy sees them,
forwards them and skips them until it finds a correct response, which
it logs and processes. As an exception, header removal/rewriting still
work on 1xx responses in order to be able to strip out sensible
information that may have accidentely been left by another equipment
(possibly an older haproxy itself). But headers addition are disabled
however.
This change brings the ability to loop on response without data, which
is a starting point to support keepalive. The change is marked as major
as a few fixes had to be performed in the HTTP message parser.
The stream_int_return() function used to call buffer_erase() on the response
buffer, which completely wipes it without taking care about whatever could
have been there. Now we more carefully strip only data not scheduled to be
sent.
This function works like a traditional putchar() except that it
can return 0 if the output buffer is full.
Now a basic character-based echo function would look like this, from
a stream interface :
while (1) {
c = buffer_si_peekchar(req);
if (c < 0)
break;
if (!buffer_si_putchar(res, c)) {
si->flags |= SI_FL_WAIT_ROOM;
break;
}
buffer_skip(req, 1);
req->flags |= BF_WRITE_PARTIAL;
res->flags |= BF_READ_PARTIAL;
}
The buffer_si_peekline() function is sort of a fgets() to be used from a
stream interface. It returns a complete line whenever possible, and does
not update the buffer's pointer, so that the reader is free to consume
what it wants to.
buffer_si_peekchar() only returns one character, and also needs a call
to buffer_skip() once the character is definitely consumed.
This functions act like their buffer_write*() counter-parts,
except that they're specifically designed to be used from a
stream interface handler, as they carefully check size limits
and automatically advance the read pointer depending on the
to_forward attribute.
buffer_feed_chunk() is an inline calling buffer_feed() as both
are the sames. For this reason, buffer_write_chunk() has also
been turned into an inline which calls buffer_write().
This flag was incorrectly used as meaning "close immediately",
while it needs to say "close ASAP". ASAP here means when unsent
data pending in the buffer are sent. This helps cleaning up some
dirty tricks where the buffer output was checking the BF_SHUTR
flag combined with EMPTY and other such things. Now we have a
clearly defined semantics :
- producer sets SHUTR and *may* set SHUTW_NOW if WRITE_ENA is
set, otherwise leave it to the session processor to set it.
- consumer only checks SHUTW_NOW to decide whether or not to
call shutw().
This also induced very minor changes at some locations which were
not protected against buffer changes while the SHUTW_NOW flag was
set. Now we prevent send_max from changing when the flag is set.
Several tests have been run without any unexpected behaviour detected.
Some more cleanups are needed, as it clearly appears that some tests
could be removed with stricter semantics.
Tarpit was broken by recent splitting of analysers. It would still
let the connection go to the server due to a missing buffer_write_dis().
Also, it was performed too late (after content switching rules).
Please consider the following patches. They are required to
compile haproxy-1.4-dev2 on FreeBSD.
Summary:
1) include <sys/types.h> before <netinet/tcp.h>
2) Use IPPROTO_TCP instead of SOL_TCP
(they are both defined as 6, TCP protocol number)
send() supports the MSG_MORE flag on Linux, which does the same
as TCP_CORK except that we don't have to remove TCP_NODELAY before
and we don't need any syscall to set/remove it. This can save up
to 4 syscalls around a send() (two for setting it, two for removing
it), and it's much cleaner since it is not persistent. So make use
of it instead.
We used to call stream_sock_data_finish() directly at the end of
a session update, but if we want to support non-socket interfaces,
we need to have this function configurable. Now we access it via
->update().
Since it's now possible to change the buffer size by configuration,
we have to take special measures against writes that are larger than
the buffer size. Before this patch, the writers would indefinitely
block, waiting for some space to free up.
With this patch, the functions simply reject the data with an
appropriate code so that the writers can either detect and process
the error or go on, but never remain blocked.
This has been tested on the stats page which does no longer hang
with buffer sizes smaller than 2.5 kB (256 bytes is even OK for
the CSV version).
The new tune.bufsize and tune.maxrewrite global directives allow one to
change the buffer size and the maxrewrite size. Right now, setting bufsize
too low will block stats sockets which will not be able to write at all.
An error checking must be added to buffer_write_chunk() so that if it
cannot write its message to an empty buffer, it causes the caller to abort.
The first step towards dynamic buffer size consists in removing
all static definitions of the buffer size. Instead, we store a
buffer's size in itself. Right now they're all preinitialized
to BUFSIZE, but we will change that.
sess_establish() used to resort to protocol-specific guesses
in order to set rep->analysers. This is no longer needed as it
gets set from the frontend and the backend as a copy of what
was defined in the configuration.
s->srv_error was set depending on the frontend's protocol. Now it is
set by the HTTP analyser, so that even when switching from a TCP
frontend to an HTTP backend, we can have HTTP error messages.
Analyser bitmaps are now stored in the frontend and backend, and
combined at configuration time. That way, set_session_backend()
does not need to perform any protocol-specific combinations.
Since the listener is the one indicating what analyser and session
handlers to call, it makes sense that it also sets the task's nice
value. This also helps getting rid of the last trace of the stats
in the proto_uxst file.
