This patch adds a warning if an http-(request|reponse) (add|set)-header
rewrite fails to change the respective header in a request or response.
This usually happens when tune.maxrewrite is not sufficient to hold all
the headers that should be added.
RFC 7234 says:
A cache MUST NOT store a response to any request, unless:
[...] the Authorization header field (see Section 4.2 of [RFC7235]) does
not appear in the request, if the cache is shared, unless the
response explicitly allows it (see Section 3.2), [...]
In this patch we completely disable the cache upon the receipt of an
Authorization header in the request. In this case it's not possible to
either use the cache or store into the cache anymore.
Thanks to Adam Eijdenberg of Digital Transformation Agency for raising
this issue.
This patch must be backported to 1.8.
Pawel Karoluk reported on Discourse[1] that HTTP/2 breaks url_param.
Christopher managed to track it down to the HTTP_MSGF_WAIT_CONN flag
which is set there to ensure the connection is validated before sending
the headers, as we may need to rewind the stream and hash again upon
redispatch. What happens is that in the forwarding code we refrain
from forwarding when this flag is set and the connection is not yet
established, and for this we go through the missing_data_or_waiting
path. This exit path was initially designed only to wait for data
from the client, so it rightfully checks whether or not the client
has already closed since in that case it must not wait for more data.
But it also has the side effect of aborting such a transfer if the
client has closed after the request, which is exactly what happens
in H2.
A study on the code reveals that this whole combined check should
be revisited : while it used to be true that waiting had the same
error conditions as missing data, it's not true anymore. Some other
corner cases were identified, such as the risk to report a server
close instead of a client timeout when waiting for the client to
read the last chunk of data if the shutr is already present, or
the risk to fail a redispatch when a client uploads some data and
closes before the connection establishes. The compression seems to
be at risk of rare issues there if a write to a full buffer is not
yet possible but a shutr is already queued.
At the moment these risks are extremely unlikely but they do exist,
and their impact is very minor since it mostly concerns an issue not
being optimally handled, and the fixes risk to cause more serious
issues. Thus this patch only focuses on how the HTTP_MSGF_WAIT_CONN
is handled and leaves the rest untouched.
This patch needs to be backported to 1.8, and could be backported to
earlier versions to properly take care of HTTP/1 requests passing via
url_param which are closed immediately after the headers, though this
is unlikely as this behaviour is only exhibited by scripts.
[1] https://discourse.haproxy.org/t/haproxy-1-8-x-url-param-issue-in-http2/2482/13
In order to use arbitrary data in the CLI (multiple lines or group of words
that must be considered as a whole, for example), it is now possible to add a
payload to the commands. To do so, the first line needs to end with a special
pattern: <<\n. Everything that follows will be left untouched by the CLI parser
and will be passed to the commands parsers.
Per-command support will need to be added to take advantage of this
feature.
Signed-off-by: Aurélien Nephtali <aurelien.nephtali@corp.ovh.com>
If TCP content inspection is used, msg_state can be >= HTTP_MSG_ERROR
the first time http_wait_for_request is called. t_idle was being left
unset in that case.
In the example below :
stick-table type string len 64 size 100k expire 60s
tcp-request inspect-delay 1s
tcp-request content track-sc1 hdr(X-Session)
%Ti will always be -1, because the msg_state is already at HTTP_MSG_BODY
when http_wait_for_request is called for the first time.
This patch should backported to 1.8 and 1.7.
In proxy mode, the result of url2sa is never checked. So when the function fails
to resolve the destination server from the URL, we continue. Depending on the
internal state of the connection, we get different behaviours. With a newly
allocated connection, the field <addr.to> is not set. So we will get a HTTP
error. The status code is 503 instead of 400, but it's not really critical. But,
if it's a recycled connection, we will reuse the previous value of <addr.to>,
opening a connection on an unexpected server.
To fix the bug, we return an error when url2sa fails.
This patch should be backported in all version from 1.5.
The management of the servers and the proxies queues was not thread-safe at
all. First, the accesses to <strm>->pend_pos were not protected. So it was
possible to release it on a thread (for instance because the stream is released)
and to use it in same time on another one (because we redispatch pending
connections for a server). Then, the accesses to stream's information (flags and
target) from anywhere is forbidden. To be safe, The stream's state must always
be updated in the context of process_stream.
So to fix these issues, the queue module has been refactored. A lock has been
added in the pendconn structure. And now, when we try to dequeue a pending
connection, we start by unlinking it from the server/proxy queue and we wake up
the stream. Then, it is the stream reponsibility to really dequeue it (or
release it). This way, we are sure that only the stream can create and release
its <pend_pos> field.
However, be careful. This new implementation should be thread-safe
(hopefully...). But it is not optimal and in some situations, it could be really
slower in multi-threaded mode than in single-threaded one. The problem is that,
when we try to dequeue pending connections, we process it from the older one to
the newer one independently to the thread's affinity. So we need to wait the
other threads' wakeup to really process them. If threads are blocked in the
poller, this will add a significant latency. This problem happens when maxconn
values are very low.
This patch must be backported in 1.8.
When the body length is undefined (no Content-Length or Transfer-Encoding
headers), The reponse remains in ending mode, waiting the request is done. So,
most of time this is not a problem because the resquest is done before the
response. But when a client sends data to a server that replies without waiting
all the data, it is really not desirable to wait the end of the request to
finish the response.
This bug was introduced when the tunneling of the request and the reponse was
refactored, in commit 4be980391 ("MINOR: http: Switch requests/responses in
TUNNEL mode only by checking txn flag").
This patch should be backported in 1.8 and 1.7.
It may be useful to keep the CO_FL_EARLY_DATA flag, so that we know early
data were used, so instead of doing this, only add the Early-data header,
and have the sample fetch ssl_fc_has_early return 1, if CO_FL_EARLY_DATA is
set, and if the handshake isn't done yet.
Maximilian Böhm, and Lucas Rolff reported some frequent HTTP/2 POST
failures affecting version 1.8.2 that were not affecting 1.8.1. Lukas
Tribus determined that these ones appeared consecutive to commit a48c141
("BUG/MAJOR: connection: refine the situations where we don't send shutw()").
It turns out that the HTTP request forwarding engine lets a shutr from
the client be automatically forwarded to the server unless chunked
encoding is in use. It's a bit tricky to meet this condition as it only
happens if the shutr is not reported in the initial request. So if a
request is large enough or the body is delayed after the headers (eg:
Expect: 100-continue), the the function quits with channel_auto_close()
left enabled. The patch above was not really related in fact. It's just
that a previous bug was causing this shutw to be skipped at the lower
layers, and the two bugs used to cancel themselves.
In the HTTP request we should only pass the close in tunnel mode, as
other cases either need to keep the connection alive (eg: for reuse)
or will force-close it. Also the forced close will properly take care
of avoiding the painful time-wait, which is not possible with the early
close.
This patch must be backported to 1.8 as it directly impacts HTTP/2, and
may be backported to older version to save them from being abused by
clients causing TIME_WAITs between haproxy and the server.
Thanks to Lukas and Lucas for running many tests with captures allowing
the bug to be narrowed down.
The new function check_request_for_cacheability() is used to check if
a request may be served from the cache, and/or allows the response to
be stored into the cache. For this it checks the cache-control and
pragma header fields, and adjusts the existing TX_CACHEABLE and a new
TX_CACHE_IGNORE flags.
For now, just like its response side counterpart, it only checks the
first value of the header field. These functions should be reworked to
improve their parsers and validate all elements.
In 1.3.8, commit a15645d ("[MAJOR] completed the HTTP response processing.")
improved the response parser by taking care of the cache-control header
field. The parser is wrong because it is split in two parts, one checking
for elements containing an equal sign and the other one for those without.
The "max-age=0" and "s-maxage=0" tests were located at the wrong place and
thus have never matched. In practice the side effect was very minimal given
that this code used to be enabled only when checking if a cookie had the
risk of being cached or not. Recently in 1.8 it was also used to decide if
the response could be cached but in practice the cache takes care of these
values by itself so there is very limited impact.
This fix can be backported to all stable versions.
In check_response_for_cacheability(), we don't check the
cache-control flags if the response is already supposed not to be
cacheable. This was introduced very early when cache-control:public
was not checked, and it basically results in this last one not being
able to properly mark the response as cacheable if it uses a status
code which is non-cacheable by default. Till now the impact is very
limited as it doesn't check that cookies set on non-default status
codes are not cacheable, and it prevents the cache from caching such
responses.
Let's fix this by doing two things :
- remove the test for !TX_CACHEABLE in the aforementionned function
- however take care of 1xx status codes here (which used to be
implicitly dealt with by the test above) and remove the explicit
check for 101 in the caller
This fix must be backported to 1.8.
There has always been something odd with the way the cache-control flags
are checked. Since it was made for checking for the risk of leaking cookies
only, all the processing was done in the response. Because of this it is not
possible to reuse the transaction flags correctly for use with the cache.
This patch starts to change this by moving the method check in the request
so that we know very early whether the transaction is expected to be cacheable
and that this status evolves along with checked headers. For now it's not
enough to use from the cache yet but at least it makes the flag more
consistent along the transaction processing.
Since RFC2616, the following codes were added to the list of codes
cacheable by default : 204, 404, 405, 414, 501. For now this it only
checked by the checkcache option to detect cacheable cookies.
We used to have a rule inherited from RFC2616 saying that the POST
method was the only uncacheable one, but things have changed since
and RFC7231+7234 made it clear that in fact only GET/HEAD/OPTIONS/TRACE
are cacheable. Currently this rule is only used to detect cacheable
cookies.
The H2 mux can cleanly report an error when a client closes, which is not
the case for the pass-through mux which only reports shutr. That was the
reason why "option abortonclose" was created since there was no way to
distinguish a clean shutdown after sending the request from an abort.
The problem is that in case of H2, the streams are always shut read after
the request is complete (when the END_STREAM flag is received), and that
when this lands on a backend configured with "option abortonclose", this
aborts the request. Disabling abortonclose is not always an option when
H1 and H2 have to coexist.
This patch makes use of the newly introduced mux capabilities reported
via the stream interface's SI_FL_CLEAN_ABRT indicating that the mux is
safe and that there is no need to turn a clean shutread into an abort.
This way abortonclose has no effect on requests initiated from an H2
mux.
This patch as well as these 3 previous ones need to be backported to
1.8 :
- BUG/MINOR: h2: properly report a stream error on RST_STREAM
- MINOR: mux: add flags to describe a mux's capabilities
- MINOR: stream-int: set flag SI_FL_CLEAN_ABRT when mux supports clean aborts
Randomly, haproxy could fail to start when a "http-request capture"
action is defined, without any change to the configuration. The issue
depends on the memory content, which may raise a fatal error like :
unable to find capture id 'xxxx' referenced by http-request capture
rule
Commit fd608dd2 already prevents the condition to happen, but this one
should be included for completeness and to reclect the code on the
response side.
The issue was introduced recently by commit 29730ba5 and should only be
backported to haproxy 1.8.
The HTTP forwarding engine needs to disable lingering on requests in
case the connection to the server has to be suddenly closed due to
http-server-close being used, so that we don't accumulate lethal
TIME_WAIT sockets on the outgoing side. A problem happens when the
server doesn't advertise a response size, because the response
message quickly goes through the MSG_DONE and MSG_TUNNEL states,
and once the client has transferred all of its data, it turns to
MSG_DONE and immediately sets NOLINGER and closes before the server
has a chance to respond. The problem is that this destroys some of
the pending DATA being uploaded, the server doesn't receive all of
them, detects an error and closes.
This early NOLINGER is inappropriate in this situation because it
happens before the response is transmitted. This state transition
to MSG_TUNNEL doesn't happen when the response size is known since
we stay in MSG_DATA (and related states) during all the transfer.
Given that the issue is only related to connections not advertising
a response length and that by definition these connections cannot be
reused, there's no need for NOLINGER when the response's transfer
length is not known, which can be verified when entering the CLOSED
state. That's what this patch does.
This fix needs to be backported to 1.8 and very likely to 1.7 and
older as it affects the very rare case where a client immediately
closes after the last uploaded byte (typically a script). However
given that the risk of occurrence in HTTP/1 is extremely low, it is
probably wise to wait before backporting it before 1.8.
This is a regression in the commit 29730ba5 ("MINOR: action: Add a functions to
check http capture rules"). We must check the capture id only when an id is
defined.
This patch must be backported in 1.8.
This BUG was introduced with:
'MEDIUM: threads/stick-tables: handle multithreads on stick tables'
The API was reviewed to handle stick table entry updates
asynchronously and the caller must now call a 'stkable_touch_*'
function each time the content of an entry is modified to
register the entry to be synced.
There was missing call to stktable_touch_* resulting in
not propagated entries to remote peers (or local one during reload)
During the migration to the second version of the pools, the new
functions and pool pointers were all called "pool_something2()" and
"pool2_something". Now there's no more pool v1 code and it's a real
pain to still have to deal with this. Let's clean this up now by
removing the "2" everywhere, and by renaming the pool heads
"pool_head_something".
Rename the global variable "proxy" to "proxies_list".
There's been multiple proxies in haproxy for quite some time, and "proxy"
is a potential source of bugs, a number of functions have a "proxy" argument,
and some code used "proxy" when it really meant "px" or "curproxy". It worked
by pure luck, because it usually happened while parsing the config, and thus
"proxy" pointed to the currently parsed proxy, but we should probably not
rely on this.
[wt: some of these are definitely fixes that are worth backporting]
This one acts similarly to its tcp-request counterpart. It immediately
closes the request without emitting any response. It can be suitable in
certain DoS conditions, as well as to close an HTTP/2 connection.
This method was reserved for the HTTP/2 connection preface, must never
be used and must be rejected. In normal situations it doesn't happen,
but it may be visible if a TCP frontend has alpn "h2" enabled, and
forwards to an HTTP backend which tries to parse the request. Before
this patch it would pass the wrong request to the backend server, now
it properly returns 400 bad req.
This patch should probably be backported to stable versions.
When a write activity is reported on a channel, it is important to keep this
information for the stream because it take part on the analyzers' triggering.
When some data are written, the flag CF_WRITE_PARTIAL is set. It participates to
the task's timeout updates and to the stream's waking. It is also used in
CF_MASK_ANALYSER mask to trigger channels anaylzers. In the past, it was cleared
by process_stream. Because of a bug (fixed in commit 95fad5ba4 ["BUG/MAJOR:
stream-int: don't re-arm recv if send fails"]), It is now cleared before each
send and in stream_int_notify. So it is possible to loss this information when
process_stream is called, preventing analyzers to be called, and possibly
leading to a stalled stream.
Today, this happens in HTTP2 when you call the stat page or when you use the
cache filter. In fact, this happens when the response is sent by an applet. In
HTTP1, everything seems to work as expected.
To fix the problem, we need to make the difference between the write activity
reported to lower layers and the one reported to the stream. So the flag
CF_WRITE_EVENT has been added to notify the stream of the write activity on a
channel. It is set when a send succedded and reset by process_stream. It is also
used in CF_MASK_ANALYSER. finally, it is checked in stream_int_notify to wake up
a stream and in channel_check_timeouts.
This bug is probably present in 1.7 but it seems to have no effect. So for now,
no needs to backport it.
This adds a new keyword on the "server" line, "allow-0rtt", if set, we'll try
to send early data to the server, as long as the client sent early data, as
in case the server rejects the early data, we no longer have them, and can't
resend them, so the only option we have is to send back a 425, and we need
to be sure the client knows how to interpret it correctly.
All the references to connections in the data path from streams and
stream_interfaces were changed to use conn_streams. Most functions named
"something_conn" were renamed to "something_cs" for this. Sometimes the
connection still is what matters (eg during a connection establishment)
and were not always renamed. The change is significant and minimal at the
same time, and was quite thoroughly tested now. As of this patch, all
accesses to the connection from upper layers go through the pass-through
mux.
locks have been added in pat_ref and pattern_expr structures to protect all
accesses to an instance of on of them. Moreover, a global lock has been added to
protect the LRU cache used for pattern matching.
Patterns are now duplicated after a successfull matching, to avoid modification
by other threads when the result is used.
Finally, the function reloading a pattern list has been modified to be
thread-safe.
This is done by passing the right stream's proxy (the frontend or the backend,
depending on the context) to lock the error snapshot used to store the error
info.
The stick table API was slightly reworked:
A global spin lock on stick table was added to perform lookup and
insert in a thread safe way. The handling of refcount on entries
is now handled directly by stick tables functions under protection
of this lock and was removed from the code of callers.
The "stktable_store" function is no more externalized and users should
now use "stktable_set_entry" in any case of insertion. This last one performs
a lookup followed by a store if not found. So the code using "stktable_store"
was re-worked.
Lookup, and set_entry functions automatically increase the refcount
of the returned/stored entry.
The function "sticktable_touch" was renamed "sticktable_touch_local"
and is now able to decrease the refcount if last arg is set to true. It
is allowing to release the entry without taking the lock twice.
A new function "sticktable_touch_remote" is now used to insert
entries coming from remote peers at the right place in the update tree.
The code of peer update was re-worked to use this new function.
This function is also able to decrease the refcount if wanted.
The function "stksess_kill" also handle a parameter to decrease
the refcount on the entry.
A read/write lock is added on each entry to protect the data content
updates of the entry.
For now, we have a list of each type per thread. So there is no need to lock
them. This is the easiest solution for now, but not the best one because there
is no sharing between threads. An idle connection on a thread will not be able
be used by a stream on another thread. So it could be a good idea to rework this
patch later.
Now, each proxy contains a lock that must be used when necessary to protect
it. Moreover, all proxy's counters are now updated using atomic operations.
First, we use atomic operations to update jobs/totalconn/actconn variables,
listener's nbconn variable and listener's counters. Then we add a lock on
listeners to protect access to their information. And finally, listener queues
(global and per proxy) are also protected by a lock. Here, because access to
these queues are unusal, we use the same lock for all queues instead of a global
one for the global queue and a lock per proxy for others.
"check_http_req_capture" and "check_http_res_capture" functions have been added
to check validity of "http-request capture" and "http-response capture"
rules. Code for these functions come from cfgparse.c.
When compiled with Openssl >= 1.1.1, before attempting to do the handshake,
try to read any early data. If any early data is present, then we'll create
the session, read the data, and handle the request before we're doing the
handshake.
For this, we add a new connection flag, CO_FL_EARLY_SSL_HS, which is not
part of the CO_FL_HANDSHAKE set, allowing to proceed with a session even
before an SSL handshake is completed.
As early data do have security implication, we let the origin server know
the request comes from early data by adding the "Early-Data" header, as
specified in this draft from the HTTP working group :
https://datatracker.ietf.org/doc/html/draft-ietf-httpbis-replay
Calls to build_logline() are audited in order to use dynamic trash buffers
allocated by alloc_trash_chunk() instead of global trash buffers.
This is similar to commits 07a0fec ("BUG/MEDIUM: http: Prevent
replace-header from overwriting a buffer") and 0d94576 ("BUG/MEDIUM: http:
prevent redirect from overwriting a buffer").
This patch should be backported in 1.7, 1.6 and 1.5. It relies on commit
b686afd ("MINOR: chunks: implement a simple dynamic allocator for trash
buffers") for the trash allocator, which has to be backported as well.
The chunk crlf parser used to depend on the channel and on the HTTP
message, eventhough it's not really needed. Let's remove this dependency
so that it can be used within the H2 to H1 gateway.
As part of this small API change, it was renamed to h1_skip_chunk_crlf()
to mention that it doesn't depend on http_msg anymore.
The chunk parser used to depend on the channel and on the HTTP message
but it's not really needed as they're only used to retrieve the buffer
as well as to return the number of bytes parsed and the chunk size.
Here instead we pass the (few) relevant information in arguments so that
the function may be reused without a channel nor an HTTP message (ie
from the H2 to H1 gateway).
As part of this API change, it was renamed to h1_parse_chunk_size() to
mention that it doesn't depend on http_msg anymore.
