There's no more reason for keepin the code and definitions in conn_stream,
let's move all that to stconn. The alphabetical ordering of include files
was adjusted.
This file contains all the stream-connector functions that are specific
to application layers of type stream. So let's name it accordingly so
that it's easier to figure what's located there.
The alphabetical ordering of include files was preserved.
An equivalent applet_need_more_data() was added as well since that function
is mostly used from applet code. It makes it much clearer that the applet
is waiting for data from the stream layer.
The new name mor eclearly indicates that a stream connector cannot make
any more progress because it needs room in the channel buffer, or that
it may be unblocked because the buffer now has more room available. The
testing function is sc_waiting_room(). This is mostly used by applets.
Note that the flags will change soon.
These functions return the app-layer associated with an stconn, which
is a check, a stream or a stream's task. They're used a lot to access
channels, flags and for waking up tasks. Let's just name them
appropriately for the stream connector.
We're starting to propagate the stream connector's new name through the
API. Most call places of these functions that retrieve the channel or its
buffer are in applets. The local variable names are not changed in order
to keep the changes small and reviewable. There were ~92 uses of cs_ic(),
~96 of cs_oc() (due to co_get*() being less factorizable than ci_put*),
and ~5 accesses to the buffer itself.
This applies the change so that the applet code stops using ci_putchk()
and friends everywhere possible, for the much saferapplet_put*() instead.
The change is mechanical but large. Two or three functions used to have no
appctx and a cs derived from the appctx instead, which was a reminiscence
of old times' stream_interface. These were simply changed to directly take
the appctx. No sensitive change was performed, and the old (more complex)
API is still usable when needed (e.g. the channel is already known).
The change touched roughly a hundred of locations, with no less than 124
lines removed.
It's worth noting that the stats applet, the oldest of the series, could
get a serious lifting, as it's still very channel-centric instead of
propagating the appctx along the chain. Given that this code doesn't
change often, there's no emergency to clean it up but it would look
better.
This renames the "struct conn_stream" to "struct stconn" and updates
the descriptions in all comments (and the rare help descriptions) to
"stream connector" or "connector". This touches a lot of files but
the change is minimal. The local variables were not even renamed, so
there's still a lot of "cs" everywhere.
When creating a new applet for peer outgoing connection, we check
the load on each thread. Threads with least applet count are
preferred.
With this solution we avoid a situation when many outgoing
connections run on the same thread causing significant load on
single CPU core.
In the same way than for the tasks, the applets api was changed to be able
to start a new appctx on a thread subset. For now the feature is
disabled. Only appctx_new_here() is working. But it will be possible to
start an appctx on a specific thread or a subset via a mask.
A .init callback function is defined for the peer_applet applet. This
function finishes the appctx startup by calling appctx_finalize_startup()
and its handles the stream customization.
The session created for frontend applets is now totally owns by the
corresponding appctx. It means the appctx is now responsible to release
it. This removes the hack in stream_free() about frontend applets to be sure
to release the session.
The two functions became exact copies since there's no more special case
for the appctx owner. Let's merge them into a single one, that simplifies
the code.
This one is the pointer to the conn_stream which is always in the
endpoint that is always present in the appctx, thus it's not needed.
This patch removes it and replaces it with appctx_cs() instead. A
few occurences that were using __cs_strm(appctx->owner) were moved
directly to appctx_strm() which does the equivalent.
Let's instead define a 4-state enum solely for this use case, and place
it into the command's context. Note that END and FIN were already
aliases, which is why they were merged.
This makes use of the generic command context allocation so that the
appctx doesn't have to declare a specific one anymore. The context is
created during parsing. The code also uses st2 which deserves being
addressed in separate commit.
This flag is no longer needed now that it must always match the presence
of a destination address on the backend conn_stream. Worse, before previous
patch, if it were to be accidently removed while the address is present, it
could result in a leak of that address since alloc_dst_address() would first
be called to flush it.
Its usage has a long history where addresses were stored in an area shared
with the connection, but as this is no longer the case, there's no reason
for putting this burden onto application-level code that should not focus
on setting obscure flags.
The only place where that made a small difference is in the dequeuing code
in case of queue redistribution, because previously the code would first
clear the flag, and only later when trying to deal with the queue, would
release the address. It's not even certain whether there would exist a
code path going to connect_server() without calling pendconn_dequeue()
first (e.g. retries on queue timeout maybe?).
Now the pendconn_dequeue() code will rely on SF_ASSIGNED to decide to
clear and release the address, since that flag is always set while in
a server's queue, and its clearance implies that we don't want to keep
the address. At least it remains consistent and there's no more risk of
leaking it.
There were plenty of leftovers from old code that were never removed
and that are not needed at all since these files do not use any
definition depending on fcntl.h, let's drop them.
Remaining flags and associated functions are move in the conn-stream
scope. These flags are added on the endpoint and not the conn-stream
itself. This way it will be possible to get them from the mux or the
applet. The functions to get or set these flags are renamed accordingly with
the "cs_" prefix and updated to manipualte a conn-stream instead of a
stream-interface.
si_shutr(), si_shutw(), si_chk_rcv() and si_chk_snd() are moved in the
conn-stream scope and renamed, respectively, cs_shutr(), cs_shutw(),
cs_chk_rcv(), cs_chk_snd() and manipulate a conn-stream instead of a
stream-interface.
The stream-interface state (SI_ST_*) is now in the conn-stream. It is a
mechanical replacement for now. Nothing special. SI_ST_* and SI_SB_* were
renamed accordingly. Utils functions to manipulate these infos were moved
under the conn-stream scope.
But it could be good to keep in mind that this part should be
reworked. Indeed, at the CS level, we only need to know if it is ready to
receive or to send. The state of conn-stream from INI to EST is only used on
the server side. The client CS is immediately set to EST. Thus current
SI_ST_* states should probably be moved to the stream to reflect the server
connection state during the establishment stage.
Flags to disable lingering and half-close are now handled at the conn-stream
level. Thus SI_FL_NOLINGER and SI_FL_NOHALF stream-int flags are replaced by
CS_FL_NOLINGER and CS_FL_NOHALF conn-stream flags.
The source and destination addresses at the applicative layer are moved from
the stream-interface to the conn-stream. This simplifies a bit the code and
it is a logicial step to remove the stream-interface.
At many places, we now use the new CS functions to get a stream or a channel
from a conn-stream instead of using the stream-interface API. It is the
first step to reduce the scope of the stream-interfaces. The main change
here is about the applet I/O callback functions. Before the refactoring, the
stream-interface was the appctx owner. Thus, it was heavily used. Now, as
far as possible,the conn-stream is used. Of course, it remains many calls to
the stream-interface API.
The conn-stream endpoint is now shared between the conn-stream and the
applet or the multiplexer. If the mux or the applet is created first, it is
responsible to also create the endpoint and share it with the conn-stream.
If the conn-stream is created first, it is the opposite.
When the endpoint is only owned by an applet or a mux, it is called an
orphan endpoint (there is no conn-stream). When it is only owned by a
conn-stream, it is called a detached endpoint (there is no mux/applet).
The last entity that owns an endpoint is responsible to release it. When a
mux or an applet is detached from a conn-stream, the conn-stream
relinquishes the endpoint to recreate a new one. This way, the endpoint
state is never lost for the mux or the applet.
It is a transient commit to prepare next changes. Now, when a conn-stream is
created from an applet or a multiplexer, an endpoint is always provided. In
addition, the API to create a conn-stream was specialized to have one
function per type.
The next step will be to share the endpoint structure.
It is a transient commit to prepare next changes. It is possible to pass a
pre-allocated endpoint to create a new conn-stream. If it is NULL, a new
endpoint is created, otherwise the existing one is used. There no more
change at the conn-stream level.
In the applets, all conn-stream are created with no pre-allocated
endpoint. But for multiplexers, an endpoint is systematically created before
creating the conn-stream.
This change is only significant for the multiplexer part. For the applets,
the context and the endpoint are the same. Thus, there is no much change. For
the multiplexer part, the connection was used to set the conn-stream
endpoint and the mux's stream was the context. But it is a bit strange
because once a mux is installed, it takes over the connection. In a
wonderful world, the connection should be totally hidden behind the mux. The
stream-interface and, in a lesser extent, the stream, still access the
connection because that was inherited from the pre-multiplexer era.
Now, the conn-stream endpoint is the mux's stream (an opaque entity for the
conn-stream) and the connection is the context. Dedicated functions have
been added to attached an applet or a mux to a conn-stream.
The appctx owner is now always a conn-stream. Thus, it can be set during the
appctx allocation. But, to do so, the conn-stream must be created first. It
is not a problem on the server side because the conn-stream is created with
the stream. On the client side, we must take care to create the conn-stream
first.
This change should ease other changes about the applets bootstrapping.
In issue #1184, cppcheck complains about some inconsistent printf
formats. At least the one in peer_prepare_hellomsg() that uses "%u"
for the int "min_ver" is wrong. Let's force other types to make it
happy, though constants cannot cause trouble.
Thanks to all previous changes, it is now possible to move the
stream-interface into the conn-stream. To do so, some SI functions are
removed and their conn-stream counterparts are added. In addition, the
conn-stream is now responsible to create and release the
stream-interface. While the stream-interfaces were inlined in the stream
structure, there is now a pointer in the conn-stream. stream-interfaces are
now dynamically allocated. Thus a dedicated pool is added. It is a temporary
change because, at the end, the stream-interface structure will most
probably disappear.
To be able to move the stream-interface from the stream to the conn-stream,
all access to the SI is done via the conn-stream. This patch is limited to
the peers part.
In the same way the conn-stream has a pointer to the stream endpoint , this
patch adds a pointer to the application entity in the conn-stream
structure. For now, it is a stream or a health-check. It is mandatory to
merge the stream-interface with the conn-stream.
Because appctx is now an endpoint of the conn-stream, there is no reason to
still have the stream-interface as appctx owner. Thus, the conn-stream is
now the appctx owner.
Thanks to previous changes, it is now possible to set an appctx as endpoint
for a conn-stream. This means the appctx is no longer linked to the
stream-interface but to the conn-stream. Thus, a pointer to the conn-stream
is explicitly stored in the stream-interface. The endpoint (connection or
appctx) can be retrieved via the conn-stream.
The approach used for skipping conn_cur in commit db2ab8218 ("MEDIUM:
stick-table: never learn the "conn_cur" value from peers") was wrong,
it only works with simple tables but as soon as frequency counters or
arrays are exchanged after conn_cur, the stream is desynchronized and
incorrect values are read. This is because the fields have a variable
length depending on their types and cannot simply be skipped by a
"continue" statement.
Let's change the approach to make sure we continue to completely parse
these local-only fields, and only drop the value at the moment we're
about to store them, since this is exactly the intent.
A simpler approach could consist in having two sets of stktable_data_ptr()
functions, one for retrieval and one for storage, and to make the store
function return a NULL pointer for local types. For now this doesn't
seem worth the trouble.
This fixes github issue #1497. Thanks to @brenc for the reproducer.
This must be backported to 2.5.
