mirror of
https://github.com/armbian/build.git
synced 2025-09-03 21:01:24 +02:00
1a12994e79
* [Early WIP] Update sunxi-next to kernel 4.17 * Switch Allwinner 32 and 64bit to U-boot 2018.05 * Adjust patched for 4.17.y / sunxi-next - adjust both configurations - removing FAT support from u-boot (breaks if you try to save) Tested those boards: Cubietruck: wlan fails http://ix.io/1fYS USB OK, HDMI yes Bananapi R40: http://ix.io/1fZm USB OK, HDMI yes Lime A64: USB no, HDMI no, wireless buggy, eMMC yes Orangepi prime H5: OK http://ix.io/1fZJ DVFS no Orangepi2e: DVFS OK, HDMI OK, net OK, wifi OK, eMMC ok, http://ix.io/1fZT * Kernel config update, enabling HDMI on CT+ * Trying to fix A64 HDMI but failed. Fixed M64 ethernet instead * Update orangepioneplus.wip * Update orangepioneplus.wip * Fix H6 build process * Add regulator bits for Orangepizero+, thanks to @5kft * add H5 support for optional 1.3v regulator and 1.3GHz operation This patch adds two optional overlays that can be used to: 1) enable the 1.1v/1.3v regulator on boards that provide the necessary compatible H/W support 2) modify the default CPU clock operating table to add new 1.2GHz and 1.3GHz clocks Note that the generated regulator overlay will only support boards whose 1.1v/1.3v regulator is controlled by GPIO PL6. * updates for the NanoPi NEO Plus2 This change introduces a patch that provides two changes for the NanoPi NEO Plus2: * Configure the "cpu0" to use the "vdd_cpux" regulator; this enables the ability to use higher CPU clocks * Correct the configurations of the on-board power and status LEDs * Adjust nightly building and few boards config cleanup
30 lines
1.0 KiB
Diff
30 lines
1.0 KiB
Diff
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts
|
|
index 495cbb17..7df39b99 100644
|
|
--- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts
|
|
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts
|
|
@@ -72,6 +72,24 @@
|
|
reset-gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */
|
|
post-power-on-delay-ms = <50>;
|
|
};
|
|
+
|
|
+ leds {
|
|
+ compatible = "gpio-leds";
|
|
+
|
|
+ pwr {
|
|
+ label = "orangepi:green:pwr";
|
|
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
|
|
+ default-state = "on";
|
|
+ };
|
|
+
|
|
+ status {
|
|
+ label = "orangepi:red:status";
|
|
+ linux,default-trigger = "mmc0";
|
|
+ gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>; /* PA17 */
|
|
+ default-state = "on";
|
|
+ };
|
|
+ };
|
|
+
|
|
};
|
|
|
|
&mmc0 {
|